Vivanco UR 810 Manual de Usario

Vivanco Mando a distancia UR 810

Lee a continuación 📖 el manual en español para Vivanco UR 810 (34 páginas) en la categoría Mando a distancia. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/34

UR 810 UNIVERSAL CONTROLLER

Vivanco GmbH, D-22926 Ahrensburg, E-Mail

: hotline@vivanco.de

, Helpline: +49 (0) 4102 231135 1

(GB) Instructions 1 

(D) Bedienungsanleitung 3 

(F) Notice d’emploi 6 

(E) Instrucciones para el uso 9 

(I) Istruzioni per l’uso 11 

(NL) Gebruiksaanwijzing 14 

(PL) Instrukcja obsługi 16 

(CZ) Návod k obsluze 19 

(P) Manual de instruções 21 

(DK) Betjeningsvejledning 24 

(S) Bruksanvisning 26 

(RUS)

  

 28

(GR) 31   

(GB) Instructions

VIVANCO UR 810 remote control for almost all

TV, audio, video and other infrared-controllable

appliances

Inserting the batteries

Open the battery flap on the back of the remote

control, press the flap lightly downwards, then

insert 2 alkaline AAA batteries. Check that the

polarity markings on the batteries and in the

battery compartment are correctly lined up

(+=+), then close the flap carefully. – Always

use undamaged batteries.

Adapting to appliances

In order to control your appliances you must

adapt or set the remote control to them. There

are three ways of doing so: direct control code

entry, code search or learn.

If your UR 810 does not understand you, it

blinks several times and you can then repeat

the entry. Each understood entry is confirmed

by an appliance button blinking once briefly.

Direct control code entry using the

enclosed list

Example: setting to control a Panasonic

television set:

1. The enclosed list gives, for

example, the Panasonic Code 153.

Please make sure you have selected the

correct list for television sets (TV).

2. To prepare code entry, press the

SET button, keep it pressend and then press

the required appliance button, e.g. TV,

additionally until the lamp (LED) inside lights

constantly.

3. Then press the number buttons

(e.g. 1 5 3) in sequence.

4. Once the numbers have been

entered the button lamp goes out and the

remote control is ready to control your

appliance.

5. Finally, test the control code setting

by trying to control (in this example) your

television set. If it does not work at all or not

correctly try a different code from the list or the

code search (see below).

6. To set the remote control for other

appliances, proceed in the same way. Instead

of the TV appliance button, press another

button e.g. VCR, DVB (SAT, DECODER),

DVD).

Code search

If the brand of your appliance is not in the list

or none of the codes given fits, we recommend

a code search.

UR 810 UNIVERSAL CONTROLLER

Vivanco GmbH, D-22926 Ahrensburg, E-Mail

: hotline@vivanco.de

, Helpline: +49 (0) 4102 231135 2

Manual code search

1. Switch on the appliance to be

controlled. Program is running.

2. To prepare code search, press the

SET button, keep it pressed and then press the

required appliance button, e.g. TV, additionally

until the lamp (LED) lights constantly.

3. Then point the remote control at the

appliance to be controlled.

4. Briefly press the ON/OFF

(appliance on/off) button once. The lamp (LED)

blinks. – Except when searching for a TV code

you can also briefly press the yellow > (Play)

button and use the Play function to search.

Make sure that a tape, a DVD or a CD is

inserted in the tape deck, player or recorder.

5. Press the ON/OFF (appliance

on/off) or Play button repeatedly, approx. every

1,5 seconds, until the appliance, e.g. your DVD

player, reacts. - If you notice the reaction of

your appliance too late and the next code has

already been emitted you can go back by

pressing SET and then ON/OFF or Play again.

If your appliance has switched itself off you

must switch it back on again, e.g. on the

appliance or with the original remote control, to

continue searching. - When your appliance

reacts you can also try out other buttons

without interrupting the search. If some buttons

do not work properly, simply continue

searching with ON/OFF or Play.

6. When your appliance reacts

correctly, press the appliance button, e.g. TV,

and end the search. The lamp (LED) goes out.

- The UR 810 continues with the search at the

point where you interrupted it. When the end of

the code list is reached the search stops

automatically. The remote control blinks quickly

several times. The code last entered remains

stored. The search stops after approx. 30

seconds of inactivity.

Automatic code search

Your remote control finds the correct settings

almost automatically in seconds:

1. Switch on the appliance to be

controlled. A channel number, for example,

appears in the display of your satellite receiver.

2. To start the code search, press the

SET button, and then additionally the required

appliance button, e.g. TV, for more than 3

seconds until the lamp (LED) starts to blink.

3. Then point the remote control at the

appliance to be controlled while the remote

control emits a different ON/OFF signal every 2

seconds.

4. When your appliance reacts, press

any button, except SET, to end the search. – If

you ended the search too late, continue to

search using the Manual Code Search (see

above).

5. Finally, test the control code setting

by trying to control, for example, your DVD

appliance. If it does not work correctly, please

try the code search again. The code search

then begins with the next code in the

sequence. - Remember to switch your

appliance, e.g. DVD, back on again if you wish

to continue searching.

Code identification

You can read off the 3-digit codes you have set

at any time:

1. Press the appliance button of the

appliance which code you want to read off, e.g.

TV.

2. Press the button and 1,2,3, SET

depending on the part of the code you want to

read off. For example, if you press + after SET 1

TV and the code 156 (in this example) has

been set, the lamp blinks once after SET+1 is

released to show that the hundred figure is 1.

All you have to do is count. The ten figure is

indicated after + is released, e.g. it blinks SET 2

5 times for the 5 in 156. The one figure is

indicated after + is released, e.g. it blinks SET 3

6 times for the 6 in 156.

Learning, Programming, of Missing Control

Functions

The LEARN function is used to supplement the

preprogrammed codes. The standard code

may provide most of functions needed, but you

may miss some key functions. Or you didn´t

find any functioning preprogrammed code for a

device. You can capture upto 100 key funtion

codes, max 40 per device. The last captured

function will overwrite the previous. learnt.

1 For learning of key codes you must use a

functioning orginal remote controller. Please

use fresh batteries for both remote controls.

2 Please point the original´s remote control

transmitter LED towards the receiver LED of

UR 810 (placed on top, same as transmitter

LED). Distance of LEDs between both remotes

shall be approximately 30mm and must be in

straight line of sight.

3 Press down and hold the Learn key and

press the device key (e.g. DVD) additionally

and then release the both pressed keys. Then

e.g. the DVD device key starts blinking

indicating that DVD key codes (functions) can

be captured.

4 Press and release the target key, that

you want to learn to (reprogram) (e.g.

POWER), the device button lights up.

5 Press and hold the source key on the

UR 810 UNIVERSAL CONTROLLER

Vivanco GmbH, D-22926 Ahrensburg, E-Mail

: hotline@vivanco.de

, Helpline: +49 (0) 4102 231135 3

original remote control (e.g. POWER) until the

LED (e.g. DVD) on your UR 810 remote control

blinks twice, then lights up for 2 seconds and

then starts blinking again.That indicates that a

new function code, e.g. POWER, has been

learnt.

6 Repeat steps 4 to 5 to for capturing more

key functions. - If there is a learning(capturing)

problem, the LED blinks 4 times, lights up for 2

seconds and then will start blinking again.

Then start capturing the key function again at

step 4.

7 Press and release device key for exit of

learning mode. – The controller will exit the

learning mode automatically after about 30

seconds of inactivity.

Reset/deletion of all captured key functions

per device: press the right device selection

key, e.g. , and then and together in DVD SET 4

order to delete all learnt functions. The

appropriate device key LED will flash twice for

confirmation.

Memory full indication: if the memory is full, a

LED blink 4 times and then the controller will

exit learnning mode.

Operation

You operate your appliances basically in

exactly the same way as if you were using the

original remote controls, except that you must

first press an appliance button (TV, DVD, etc.)

to control the required appliance. As the

symbols on the UR 810 could differ from those

on the original remote controls you may have

to try out all the buttons in order to find the

functions.

Special settings and functions

1. Assigning volume and mute

exclusively to one appliance (punch through

function: Press the appliance button of the

appliance that you always want to use for

volume control, e.g. DVB. To lock, press SET

and . To unlock, press and . 5 SET 6

2. Device Selection Key Shift: In order

to change the function of a device selection

key, e.g. change device key to a second AUX1

SAT device key proceed as follows:

a) Press hold it and then press the to be SET

changed device key, e.g. . Then release AUX1

both keys and the light will be on. AUX1

b) Press , the light goes off and you can SAT

enter another code for a second SAT or SAT

DTT receiver under . AUX1

c) You can reset this function by pressing SET

and the modified device key ( ) AUX1

simultanously until the LED goes on. Then

release the keys and press the modified device

key (AUX1) again.

3. Locking and unlocking a set device

key: Press the appliance key of the appliance

that you always want to be locked. Preset code

not changeable. To lock, press and . To SET 7

unlock, press and 8. SET

4. Reset remote control to factory

settings: Press and simultanously for SET 0

more then 3 seconds. A LED will flash twice

and all user settings will be deleted

Specifications

Batteries: 2x AAA batteries, R03, UM4

Range: max. 7 m

Not for 400 kHz equipment

2-year works guarantee

Should your UR 810 cease to work within 2

years of purchasing you will receive a free

replacement from VIVANCO. Exceptions:

missing codes, deliberate destruction and

normal wear and tear of the housing and

buttons.

(D) Bedienungsanleitung

Fernbedienung Vivanco UR 810 für fast alle

Fernseh-, Audio-, Video und anderen

infrarotsteuerbaren Geräte

Batterien einlegen

Bitte öffnen Sie die Batterieklappe an der

Geräterückseite, Klappe leicht nach

untenschieben, und legen Sie 2 Alkali-

Mikrozellenbatterien ein. Achten Sie auf die

angegebenen Polaritäten auf Batterien und im

Batteriefach (+=+), und schließen Sie das Fach

wieder vorsichtig. – Bitte achten Sie darauf,

immer einwandfreie Batterien zu verwenden.

Geräteanpassung

Um Ihre Geräte steuern zu können, müssen

Sie die Fernbedienung für Ihre Geräte

einstellen. Dazu gibt es zwei Möglichkeiten: die

direkte Steuerkodeeingabe und die

Kodesuche.

Wenn die UR 810 Sie nicht versteht, dann

blinkt sie 2 Mal und Sie können danach die

Eingabe wiederholen. Jede verstandene

Eingabe quittiert sie mit einem kurzen Blink

ihrer LED-Anzeigelampe.

Die direkte Steuerkodeeingabe mithilfe der

beigefügten Liste

Beispiel: Einstellung der Fernbedienung für ein

Panasonic-Fernsehgerät:

1. Aus der beigefügten Liste

entnehmen Sie z.B. den Panasonic-Code 153.

Bitte vergewissern Sie sich, dass Sie die

korrekte Liste für Fernseher (TV) gewählt

haben.

Especificaciones del producto

Marca:	Vivanco
Categoría:	Mando a distancia
Modelo:	UR 810

¿Necesitas ayuda?

Si necesitas ayuda con Vivanco UR 810 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

Mando a distancia Vivanco Manuales

Vivanco vivcontrol 5 se Manual de Usario

7 Septiembre 2024

Vivanco UR12NB Manual de Usario

7 Septiembre 2024

Vivanco vivcontrol 3 se Manual de Usario

7 Septiembre 2024

Vivanco UR 1200 Manual de Usario

30 Agosto 2024

Vivanco UR 81 Manual de Usario

29 Agosto 2024

Vivanco 37600 Manual de Usario

28 Agosto 2024

Vivanco Viv.Control 3 Manual de Usario

28 Agosto 2024

Vivanco UR 1250 Manual de Usario

27 Agosto 2024

Vivanco UR ZAP2 Manual de Usario

26 Agosto 2024

Vivanco UR Z2 Manual de Usario

26 Agosto 2024

Mando a distancia Manuales

Últimos Mando a distancia Manuales

Monacor DRM-880WP Manual de Usario

27 Octubre 2024

Hama Spot-Pointer V2 Manual de Usario

26 Octubre 2024

Sony RM-ED022 Manual de Usario

21 Octubre 2024

Sonos Control Manual de Usario

18 Octubre 2024

One For All URC 7935 Manual de Usario

18 Octubre 2024

Canon BG-E20 Manual de Usario

12 Octubre 2024

Neewer RT112 Manual de Usario

8 Octubre 2024

Neewer RT113 Manual de Usario

8 Octubre 2024

Logitech Harmony 785 Manual de Usario

8 Octubre 2024

DSC WS4949 Manual de Usario

8 Octubre 2024