Whirlpool YWMH53521HW Manual de Usario
Lee a continuación 📖 el manual en español para Whirlpool YWMH53521HW (32 páginas) en la categoría Magnetron. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/32
MICROWAVE HOOD COMBINATION
INSTALLATION INSTRUCTIONS
This product is suitable for use above electric or gas cooking products up to and including 36" (91.4 cm) wide. See the “Installation
Requirements” section for further notes.
These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration
in these installation instructions.
INSTRUCTIONS D’INSTALLATION
DE L’ENSEMBLE FOUR À MICRO-ONDES/HOTTE
Ce produit est conçu pour l’utilisation au-dessus d’appareils de cuisson électriques ou à gaz de 36 po (91,4 cm) de largeur ou moins.
Voir la section « Exigences d’installation » pour d’autres remarques.
Ces instructions d’installation sont valables pour plusieurs modèles. Il se peut que l’apparence de votre propre modèle soit légèrement
différente de celle montrée sur les illustrations dans ce document.
Table of Contents/Table des matières
W11496339A
MICROWAVE HOOD COMBINATION SAFETY ............................2
INSTALLATION REQUIREMENTS .................................................2
Tools and Parts .............................................................................2
Separate Cardboard Template .....................................................3
Location Requirements ................................................................3
Product Dimensions .....................................................................3
Electrical Requirements ...............................................................4
INSTALLATION INSTRUCTIONS ...................................................5
Remove Mounting Plate ...............................................................5
Rotate Blower Motor ....................................................................5
Locate Wall Stud(s) ......................................................................8
Mark Rear Wall .............................................................................9
Drill Holes in Rear Wall ...............................................................10
Attach Mounting Plate to Wall ...................................................10
Prepare Upper Cabinet ..............................................................11
Install Damper Assembly
(for wall venting only) ..................................................................11
Install the Microwave Oven ........................................................12
Complete Installation .................................................................13
VENTING DESIGN SPECIFICATIONS ........................................14
ASSISTANCE ................................................................................15
Replacement Parts .....................................................................15
Accessories ................................................................................15
SÉCURITÉ DE L’ENSEMBLE FOUR À
MICRO-ONDES/HOTTE...............................................................16
EXIGENCES D’INSTALLATION ...................................................16
Outillage et pièces ......................................................................16
Gabarit en carton séparé ...........................................................17
Exigences d’emplacement .........................................................17
Dimensions du produit ...............................................................18
Spéci cations électriques ..........................................................18
INSTRUCTIONS D’INSTALLATION .............................................19
Dépose de la plaque de montage ..............................................19
Réorientation du moteur du ventilateur .....................................19
Identi er la position du/des poteau(x) du colombage mural .....22
Tracé sur le mur arrière ..............................................................23
Perçage de trous dans le mur arrière .........................................24
Fixation de la plaque de montage sur le mur ............................24
Préparation du placard supérieur ..............................................25
Installation du module du clapet anti-re ux
(pour décharge à travers le mur uniquement) ............................25
Installation du four à micro-ondes .............................................26
Achever l’installation ..................................................................28
SPÉCIFICATIONS/CONCEPTION DU CIRCUIT
D’ÉVACUATION ...........................................................................28
ASSISTANCE ................................................................................30
Pièces de rechange ....................................................................30
Accessoires ................................................................................30
2
MICROWAVE HOOD COMBINATION SAFETY
INSTALLATION REQUIREMENTS
Tools and Parts
Tools Needed
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
■Measuring tape
■Pencil
■Masking tape or thumbtacks
■Scissors
■No. 2 Phillips screwdriver
■No. 3 Phillips screwdriver
for 1/4-20 x 3" (7.6 cm) bolts
■Drill
■3/16" (5 mm), 3/8" (1cm),
5/8" (1.6 cm) drill bits
■3/4" (1.9 cm) hole saw
■Diagonal wire cutting pliers
■Stud nder
■7⁄16" (1.1 cm) socket wrench (or box wrench) for 1/4" x 2"
(6.4 mm x 5.1cm) lag screws
■11/2" (3.8 cm) diameter hole drill bit for wood or metal cabinet
■Keyhole saw
■Caulking gun and weatherproof caulking compound
■Duct tape
Parts Needed
For information on reordering, see the “Replacement Parts”
section.
NOTE: The hardware items listed here are for wood studs.
For other types of wall structures, be sure to use appropriate
fasteners.
NOTE: Depending on model, aluminum grease lter and
charcoal lter may be combined.
Materials Needed
Standard ttings for wall or roof venting. See the “Venting Design
Speci cations” section.
A B C D E F G
H
A. 3/16-24 x 3" round-head
bolts (2)
B. 1/4-20 x 3" at-head bolts (2)
C. Washers (2)
D. 3/16" toggle nuts (2)
E. 1/4" x 2" lag screws (2)
F. #6 x 3/8" Sheet metal screws (2)
G. Power supply cord bushing (1)
H. Damper assembly (for wall or
roof venting)
Not Shown:
■Mounting plate (attached to
back of microwave oven)
■Cardboard template (part of
packaging)
■Aluminum grease lters
■Charcoal lters (Depending
on model, charcoal lters may
not be included. See User
Instructions.)
3
Separate Cardboard Template
The wall template and upper cabinet template is embedded in
the backside of the carton box. They are used as a rear wall
template and upper cabinet template.
1. Cut along the dotted line to separate the cardboard template
from the backside of the carton box.
2. Set the cardboard template to the side and refer to it during
the “Mark Rear Wall” and “Prepare Upper Cabinet” parts of
installation.
Location Requirements
Check the opening where the microwave oven will be installed.
The location must provide:
■Minimum installation dimensions. See the “Installation
Dimensions” illustration.
■Minimum one 2" x 4" (5.1 x 10.2 cm) wood wall stud and
minimum 3/8" (1 cm) thickness drywall or plaster/lath within
cabinet opening.
■Support for weight of 150 lbs (68 kg) which includes
microwave oven and items placed inside the microwave
oven and upper cabinet.
■Grounded electrical outlet inside upper cabinet. See the
“Electrical Requirements” section.
NOTES:
■If installing the microwave oven near a left sidewall, make
sure there is at least 6" (15.2 cm) of clearance between the
wall and the microwave oven so that the door can open fully.
■Some models have a pocket handle. If installing the
microwave near a right side wall, make sure there is at least
3" (7.6 cm) of clearance between wall and microwave oven
so you can grab the handle integrated inside the door.
■Some cabinet and building materials are not designed to
withstand the heat produced by the microwave oven for
cooking. Check with your builder or cabinet supplier to make
sure that the materials used will not discolor, delaminate, or
sustain other damages.
Special Requirements
For Wall Venting Installation Only:
■Cutout must be free of any obstructions so that the vent t
properly and the damper blade opens freely and fully.
For Roof Venting Installation Only:
■If you are using a rectangular-to-round transition piece, the
3" (7.6 cm) clearance needs to exist above the microwave
oven so that the damper blade can open freely and fully.
See “Rectangular to Round Transition” illustration in the
“Venting Design Speci cations” section.
Installation Dimensions
NOTE: The grounded 3 prong outlet must be inside the upper
cabinet. See the “Electrical Requirements” section.
*30" (76.2 cm) is typical for 66" (167.6 cm) installation height.
Exact dimensions may vary depending on type of range/cooktop
below.
NOTE: To ensure good performance, do not obstruct top vent
air ow. If cabinets are deeper than 14" (35.6 cm) but no more
than 15" (38.1 cm), use the bump out mounting kit replacing the
I bar mounting plate from the wall. The bump out mounting kit
(part # W11185746) is not provided but can be purchased from
Whirlpool.
Product Dimensions
*Overall depth of product will vary slightly depending on door
design.
A. 2" x 4" (5.1 x 10.2 cm) wall stud
B. Grounded 3 prong outlet
12" (30.5 cm) minimum
14" (35.6 cm) maximum
30"
(76.2 cm)
minimum
A B
upper cabinet and
side cabinet depth
30"
(76.2 cm)
typical*
66" (167.6 cm) minimum
I bar mounting plate
Bump out mounting bracket
12" DEEPER 14" 14" DEEPER 15"
16
¹⁄₄
"
(41.3 cm)
17
¹⁄₈
"
(43.5 cm)
+/-
3/16
(0.5 cm)
17"
Up to
(43.2 cm)*
cm)
29
⁷⁄₈
" (76.0
"
B
A
A. Backside of the carton box
B. Cardboard template (including Rear Wall template and Upper
Cabinet template)
Especificaciones del producto
| Marca: | Whirlpool |
| Categoría: | Magnetron |
| Modelo: | YWMH53521HW |
¿Necesitas ayuda?
Si necesitas ayuda con Whirlpool YWMH53521HW haz una pregunta a continuación y otros usuarios te responderán
Magnetron Whirlpool Manuales
19 Octubre 2024
17 Octubre 2024
16 Octubre 2024
15 Octubre 2024
14 Octubre 2024
14 Octubre 2024
8 Octubre 2024
8 Octubre 2024
7 Octubre 2024
3 Octubre 2024
Magnetron Manuales
- Magnetron Candy
- Magnetron Electrolux
- Magnetron Samsung
- Magnetron ATAG
- Magnetron LG
- Magnetron Bosch
- Magnetron AEG
- Magnetron IKEA
- Magnetron Panasonic
- Magnetron AEG Electrolux
- Magnetron Bauknecht
- Magnetron BEKO
- Magnetron Delonghi
- Magnetron Daewoo
- Magnetron Etna
- Magnetron Grundig
- Magnetron Indesit
- Magnetron Inventum
- Magnetron Kenwood
- Magnetron Miele
- Magnetron Medion
- Magnetron Quigg
- Magnetron Siemens
- Magnetron Zanussi
- Magnetron Zanker
- Magnetron ACP
- Magnetron Alpina
- Magnetron Amica
- Magnetron Amana
- Magnetron Silverline
- Magnetron Bartscher
- Magnetron Morphy Richards
- Magnetron GE
- Magnetron Orbegozo
- Magnetron Brother
- Magnetron Sharp
- Magnetron Fisher And Paykel
- Magnetron Bertazzoni
- Magnetron Lamona
- Magnetron Klarstein
- Magnetron Fagor
- Magnetron Brandt
- Magnetron Severin
- Magnetron Smeg
- Magnetron Gorenje
- Magnetron Neff
- Magnetron Palsonic
- Magnetron Silvercrest
- Magnetron Baumatic
- Magnetron Hitachi
- Magnetron Thomson
- Magnetron Korona
- Magnetron Hoover
- Magnetron Saturn
- Magnetron Black And Decker
- Magnetron Breville
- Magnetron KitchenAid
- Magnetron Innoliving
- Magnetron Domo
- Magnetron Teka
- Magnetron Trisa
- Magnetron Progress
- Magnetron Cata
- Magnetron Gaggenau
- Magnetron Hotpoint-Ariston
- Magnetron Ignis
- Magnetron Maytag
- Magnetron OBH Nordica
- Magnetron Manta
- Magnetron Thermador
- Magnetron OK
- Magnetron Hisense
- Magnetron Hyundai
- Magnetron Hanseatic
- Magnetron Cylinda
- Magnetron Bellini
- Magnetron Avanti
- Magnetron Westinghouse
- Magnetron ECG
- Magnetron Moulinex
- Magnetron Pelgrim
- Magnetron Blomberg
- Magnetron Melissa
- Magnetron Magic Chef
- Magnetron Swan
- Magnetron RCA
- Magnetron Scarlett
- Magnetron Clatronic
- Magnetron Russell Hobbs
- Magnetron Constructa
- Magnetron Summit
- Magnetron Hotpoint
- Magnetron Sencor
- Magnetron Midea
- Magnetron De Dietrich
- Magnetron Junker
- Magnetron Blaupunkt
- Magnetron Monogram
- Magnetron Frigidaire
- Magnetron Svan
- Magnetron Logik
- Magnetron Danby
- Magnetron Balay
- Magnetron Valberg
- Magnetron Stirling
- Magnetron PKM
- Magnetron Rosieres
- Magnetron Salora
- Magnetron Profilo
- Magnetron CDA
- Magnetron Hendi
- Magnetron Mellerware
- Magnetron Schneider
- Magnetron Sanyo
- Magnetron Vitek
- Magnetron Maxxmee
- Magnetron Kenmore
- Magnetron Philco
- Magnetron Nabo
- Magnetron Guzzanti
- Magnetron Defy
- Magnetron Infiniton
- Magnetron Aspes
- Magnetron Schaub Lorenz
- Magnetron Nordmende
- Magnetron Husqvarna
- Magnetron Koenic
- Magnetron Haier
- Magnetron Friac
- Magnetron Boretti
- Magnetron Ariston Thermo
- Magnetron Wolkenstein
- Magnetron Hansa
- Magnetron Exquisit
- Magnetron Elba
- Magnetron Proline
- Magnetron Euromaid
- Magnetron Corberó
- Magnetron WLA
- Magnetron Zelmer
- Magnetron Kelvinator
- Magnetron Mora
- Magnetron Bomann
- Magnetron Hamilton Beach
- Magnetron Zerowatt
- Magnetron Kuppersbusch
- Magnetron Continental Edison
- Magnetron Jenn-Air
- Magnetron Limit
- Magnetron Insignia
- Magnetron Edesa
- Magnetron Milectric
- Magnetron Wilfa
- Magnetron New World
- Magnetron Nodor
- Magnetron WhiteLine
- Magnetron Jocel
- Magnetron Viva
- Magnetron Respekta
- Magnetron M-System
- Magnetron Primo
- Magnetron Rex
- Magnetron Creda
- Magnetron Tower
- Magnetron Comfee
- Magnetron Dacor
- Magnetron Saro
- Magnetron Scandomestic
- Magnetron V-Zug
- Magnetron Godrej
- Magnetron Sauber
- Magnetron MPM
- Magnetron Becken
- Magnetron Ices
- Magnetron Cello
- Magnetron Essentiel B
- Magnetron Team
- Magnetron Vivax
- Magnetron Nevir
- Magnetron Ilve
- Magnetron G3 Ferrari
- Magnetron Caple
- Magnetron Wolf
- Magnetron Carrefour Home
- Magnetron Kunft
- Magnetron Caso
- Magnetron Upo
- Magnetron Conceptronic
- Magnetron ZLine
- Magnetron Grunkel
- Magnetron Belion
- Magnetron Waves
- Magnetron Scancool
- Magnetron Veripart
- Magnetron Home Electric
- Magnetron Lynx
- Magnetron Barazza
- Magnetron Cecotec
- Magnetron Bluesky
- Magnetron Tecnolux
- Magnetron Micromaxx
- Magnetron Kalorik
- Magnetron La Germania
- Magnetron Technolux
- Magnetron Holland Electro
- Magnetron Prima Donna
- Magnetron Oranier
- Magnetron Tisira
- Magnetron Apelson
- Magnetron Foster
- Magnetron Thomas
- Magnetron Mei
- Magnetron Kogan
- Magnetron Solwave
- Magnetron Signature
- Magnetron JennAir
- Magnetron Flama
- Magnetron LERAN
- Magnetron Fulgor Milano
- Magnetron Microstar
- Magnetron WestBend
- Magnetron XO
- Magnetron Artusi
- Magnetron Merrychef
- Magnetron Sôlt
- Magnetron Powertec
- Magnetron Commercial Chef
- Magnetron Cosmo
- Magnetron VENINI
- Magnetron Deco
- Magnetron DCS
- Magnetron Artrom
- Magnetron Cookology
- Magnetron Arthur Martin-Electrolux
- Magnetron Elektra Bregenz
- Magnetron Menumaster
- Magnetron Porter & Charles
- Magnetron Café
- Magnetron Classique
- Magnetron Smart Brand
- Magnetron Pelonis
- Magnetron Imarflex
- Magnetron Pitsos
- Magnetron Yamazen
Últimos Magnetron Manuales
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
25 Octubre 2024
24 Octubre 2024
24 Octubre 2024
24 Octubre 2024