Xantech Dinky Link 48095D Manual de Usario

Xantech receptor Dinky Link 48095D

Lee a continuación 📖 el manual en español para Xantech Dinky Link 48095D (10 páginas) en la categoría receptor. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/10
08905105A - 1 -
INSTALLATION INSTRUCTIONS
490-85
CLF / LCD Friendly Micro Link IR Receiver
DESCRIPTION
The 490-85 is a CFL (compact fluorescent light) / LCD (liquid crystal display) version of the 490 Micro
Link series IR receivers. It is specifically designed to have greater immunity to high frequency
ballasted CFL and overhead fluorescent type infrared inference and to have exceptional IR reception
range.
These small IR receivers have been designed primarily for mounting in panels, doors, cabinets, etc.
for control of A/V equipment behind closed doors. They may be mounted in walls, ceilings, wall
speakers, etc. - anywhere an inconspicuous appearance is desired. Their high sensitivity allows
placement behind speaker grilles and still receiver IR commands up to 20 feet away.
FEATURES AND SPECIFICATIONS
IR carrier frequency reception bandwidth: 30 to 60 kHz.
IR carrier adjustment: 32 to 56 kHz (allows output carrier frequency to be matched to a
controlled component for optimum performance).
IR reception range: > 50 feet
Dimensions: 2.75” Length x 0.75” DIA. Bezel is 0.90” DIA.
Works in normal 3-wire mode (12VDC, IR, GND).
Red talkback LED for system verification.
RF Grid included for EMI interference reduction.
Includes 3-Terminal Block for easy extension of 7 foot ribbon cable.
7 units may be powered by one 781RG power supply.
Normal Operating Power: +12VDC, 20mA.
Note: The 490-85 will not operate in 2-wire Phantom Power mode.
INSTALLATION
This unit is meant to be interfaced to Xantech Connecting Blocks, such as CB12, 789-44, 791-44, etc.
MOUNTING
1. Drill a 3/4” hole in any flat surface, such as a cabinet panel. Pass the cable and body of the
490-85 through the hole and secure from the rear with the nut (supplied).
08905105A - 2 -
IR CARRIER ADJUSTMENT
The 490-85 is factory set to an IR carrier repeat frequency of 39kHz. This will be correct for the
majority of installations. However, some manufacturer’s components that you wish to control may use
different carrier frequencies (such as RCA DSS satellite receivers that use 56kHz). If sure carrier
frequencies fall within the range of 32kHz to 56kHz, you can adjust the 490-85 to match them for the
best range performance. The adjustment can be made through the small opening on the rear.
To adjust, proceed as follows:
1. First, try the 490-85 in a repeater system. If it works well with good range, do not make any
adjustments!
2. If it does not work or has poor range (less than 15 feet), determine the IR carrier frequency of
the product you wish to control. Contact the manufacturer of the product, if necessary, to
determine this frequency.
3. Using a small blade type screwdriver, rotate the adjustment shaft until the slot lines up with the
desired frequency.
4. If you have products in the same IR system that have different IR carrier frequencies, you will
have to adjust the 490-85 to a midway position. For example, some may operate at 38kHz and
others at 56kHz. In this case, set the adjustment to approximately 47kHz, a midway position.
Note: Some products are more tolerant of compromised frequency settings that others. You may
have to “fine tune” the adjustment to “favor” the least tolerant component for the best performance
of all units in the system.
Clock-wise (CW) Increase carrier frequency
Counter Clock-wise (CCW) Decrease carrier frequency
490-85 CABLE CONNECTIONS
The 490-85 may also be used where the 7-foot lead is not long enough. In this case, simply cut off
the mini plug, strip the leads and connect them to a 3-terminal block. For correct color identification of
wires, refer to the following tables and diagrams:
PLUG CABLE LEADS DESCRIPTION
RING BLACK GROUND
TIP WHITE IR OUTPUT
SLEEVE RED +12V
Tip
Ring
Sleeve Insulators
Mini Plug
(3-Conductor)
3-Terminal
Block
OUT
+12V
GND
WHITE
3-Conductor
Wire to
Controlled
Equipment
490-85
7-Foot 3-Conductor Cable
with Mini Plug removed
See Tables for
Wire Color
08905105A - 3 -
APPLICATION WIRING
A typical system, with a 490-85, 781RG Power Supply and 283M Emitters plugged into a 791-44
Connecting Block, is shown in the figure below.
1. Plug the 3.5 mm stereo mini plug from the 490-85 into the 791-44 connecting block labeled “IR
RCVR”.
2. Plug in the 3.5 mm mono mini plug from any of the 282, 284, 283 and 286 series Emitters into
the jacks labeled EMITTERS on the 791-44 Connecting Block and affix the opposite end of the
IR Sensor Window of the controlled equipment.
3. Plug in the 2.1mm Coaxial power plug of the 781RG Power Supply (not included) into the jack
labeled 12VDC on the 791-44 Connecting Block.
4. Plug the AC end of the 781RG Power Supply into an ‘un-switched’ 120VAC outlet.
490-85
Series
IR Receivers
283M
Emitter
120 V AC
(Unswitched)
781RG
Power Supply
791-44
Amplified
Connecting Block
283M
Emitter
283M
Emitter
0.469"
1 7/8"
7 Foot 3-Conductor
Cable with Quick
Connect Mini Plug
+12 VDC
GND
E M I T T E R S
MODEL 791-44
AMPLIFIED
CONNECTING B LO CK
XANT ECH CORPORATION.
SYLMAR CA MADE IN U.S.A.
12 VDC
HI
IR
OUT
STAT U S
IR I N
RCVR
Hand Held
Remote
Controlled Equipment
(mounted behind
closed cabinet doors)
490-85
(mounted on or
near cabinet in an
inconspicuous
location). 283M
Emitter
283M
Emitter
Satellite Receiver
Cable Box
AV Receiver
CD Changer
Cassette DecK

Especificaciones del producto

Marca: Xantech
Categoría: receptor
Modelo: Dinky Link 48095D

¿Necesitas ayuda?

Si necesitas ayuda con Xantech Dinky Link 48095D haz una pregunta a continuación y otros usuarios te responderán


receptor Xantech Manuales

Xantech

Xantech ML95K Manual de Usario

10 Septiembre 2024
Xantech

Xantech DL95K Manual de Usario

10 Septiembre 2024
Xantech

Xantech Micro Link ML85 Manual de Usario

10 Septiembre 2024
Xantech

Xantech Dinky Link 48095D Manual de Usario

7 Septiembre 2024
Xantech

Xantech Dinky Link 48085DB Manual de Usario

7 Septiembre 2024

receptor Manuales

Últimos receptor Manuales

Crown

Crown CDi DriveCore 2|300BL Manual de Usario

27 Octubre 2024
Boss

Boss PT3000 Manual de Usario

27 Octubre 2024
Speco Technologies

Speco Technologies PBM120AT Manual de Usario

27 Octubre 2024
Fosi Audio

Fosi Audio V3 Manual de Usario

26 Octubre 2024
Jensen

Jensen CAR710-4BC Manual de Usario

25 Octubre 2024
Onkyo

Onkyo TX-RZ830 Manual de Usario

24 Octubre 2024
Pioneer

Pioneer VSX-1122K Manual de Usario

22 Octubre 2024
Yamaha

Yamaha HTR-5072 Manual de Usario

21 Octubre 2024
NAD

NAD C 355BEE Manual de Usario

20 Octubre 2024
Yamaha

Yamaha RX-A810 Manual de Usario

20 Octubre 2024