Zodiac TP500 Manual de Usario

Zodiac filtro de agua TP500

Lee a continuación 📖 el manual en español para Zodiac TP500 (3 páginas) en la categoría filtro de agua. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/3

1-4

FUNCTION

INSTALLATION

THIS FILTER OPERATES UNDER HIGH PRESSURE. WHEN ANY PART OF THE CIRCULATING

SYSTEM (e.g., CLAMP, PUMP, FILTER, VALVES, ETC.) IS SERVICED, AIR CAN ENTER THE

SYSTEM AND BECOME PRESSURIZED . PRESSURIZED AIR CAN CAUSE THE LID OR VALVE TO

BE BLOWN OFF WHICH CAN RESULT IN SEVERE INJURY, DEATH, OR PROPERTY DAMAGE

TURN PUMP OFF BEFORE CHANGING VALVE POSITION.

WARNING

4-4

TO PREVENT DAMAGE TO THE PUMP AND FOR PROPER OPERATION OF THE SYSTEM,

CLEAN PUMP STRAINER AND SKIMMER BASKETS REGULARLY.

DO NOT UNSCREW SCREWS OF FLANGE CLAMP WHILE PUMP IS RUNNING.

ASFI09051703

FUNCTIONS OF VALVE POSITIONS

WASTE

FILTER

BACKWASH RINSE

WASTE

RECIRCULATE

CLOSED

WASTE WASTE

WASTE WASTE WASTE

IN FLOW OUT FLOW IN FLOW OUT FLOW IN FLOW OUT FLOW

GENERAL

SERVICING VALVE( Stop pump,close gate valve in suction&discharge before proceeding):

a. Set handle in filter position. b. Remove cover screws. c. Lift cover and key assembly out.

TO ASSEMBLE:

1. Place valve key so that wedge opening is at TOP port (handle in Filter psn.). Flat edge of cover screw lug should align with

flat edge of body screw lug.

2. Position cover o’ring.

3. Secure assembly to body with cover screws. Tighten cover screws evenly and alternately. Do not over-tighten.

The filter uses special filter sand to remove dirt particles from pool water. The filter sand is loaded into the filter tank and functions as

a permanent dirt removing media. When the control valve is in the FILTER position, the pool water which contains suspended dirt

particles, is pumped through your piping system and is automatically directed by the patented filter control valve to the top of the filter

tank. As the pool water is pumped through the filter, dirt particles are trapped by the sand bed, and filtered out. The cleaned pool water is

returned from the bottom of the filter tank, through the control valve and back to the pool through the piping system. This entire sequence

is continuous and automatic. It provides for total recirculation of pool water through your filter and piping system.

After a period of time, the accumulated dirt in the filter causes a resistance to flow, and the flow diminishes. This means it is time to

clean your filter. With the control valve in the BACKWASH position, the water flow is automatically reversed through the filter so that it

is directed to the bottom of the tank, up through the sand, flushing the previously trapped dirt and debris out the waste line. Once the filter

is back-washed of dirt, set control valve to RINSE position and run pump for about 1/2 to 1 minute, and then set the control valve in the

FILTER position, to resume normal filtering.

NOTE: Turn pump off before changing valve position.

TITAN SERIES SAND FILTER

Model : TP500, TP650, TP700

(Link by Clamp type Valves)

Only simple tools (screwdriver and wrenches), plus pipe sealant for plastic adapters, are required to install and

service the filter.

1. The filter should be placed on a level concrete slab, very firm ground, or equivalent. The filter should be placed

2. Loading the sand media. Filter sand media is loaded through the top opening of the filter.

a. Loosen the flange clamp and remove filter control valve (if previously installed).

b. Cap internal pipe with plastic cap to prevent sand from entering it.

c. We recommend filling the tank approximately 1/2 way with water to provide a cushion effect when the filter

d. Carefully pour in correct amount and grade of filter sand. (Be sure center pipe remains centered in opening.)

internal pipe.

in the right position so that the piping connections, control valve are convenient and accessible for operation and service.

sand is poured in. This helps protect the under-drain laterals from excessive shock.

Sand surface should be leveled and should come to about the middle of the filter tank. Remove plastic cap from

Valve Position Function

FILTER

BACKWASH

RINSE

WASTE

RECIRCULATE

CLOSED

Normal Filtration and Vacuuming

Cleaning Filter by reversing the flow

Used after backwash to flush dirt from valve

By-passes filter, used for vacuuming to waste or lowering water level

By-passes filter for circulating water to pool

Shuts off all flow to filter or pool

2-4

3. Assemble filter control valve into the filter tank.

a. Insert filter control valve (with o'ring in place) into the tank neck, taking care that the center pipe slips into the hole

b. Place two plastic clamps around valve flange and tank flange and tighten just enough so that the valve may be

d. Connect pump to control valve opening marked PUMP. After connections are made, tighten valve flange clamps with

plumbing connections, suction lines to pump, waste, etc.

5. Make electrical connections to pump per pump instructions.

6. To prevent water leakage, make sure all pipe connections are tight.

4. Make return to pool pipe connection to control valve opening marked RETURN and complete other necessary

MAIN DIMENSION

in the bottom of the valve.

rotated on tank for final positioning.

c. Carefully screw pressure gauge (with o'ring in place) into tapped hole in valve body. Do not over-tighten.

screwdriver, tapping around clamp with screwdriver handle to help seat valve flange clamp.

REPLACEMENT PARTS OF FILTER

3-4

1. Make sure the correct amount of filter media sand is located in the tank and all connections have been connected and secured.

2. Depress control valve handle and rotate to BACKWASH position. (To prevent damage to control valve seal, always depress handle

before turning.)

3. Prime and start pump according to pump instructions (be sure all suction and return lines are open), allowing the filter tank to fill with

water. Once water is flowing out of the waste line, run the pump for at least 1 minute. The initial back-washing of the filter is

recommended to remove any impurities or fine sand particles in the sand media.

4. Turn pump off and set valve to RINSE position. Start pump and operate until water in sight glass is clear, about 1/2 to 1 minute. Turn

pump off and set valve to FILTER position and restart pump. The filter is now operating in the normal filter mode, filtering dirt particles

from the pool water.

5. Adjust pool suction and return valves to achieve desired flow. Check system and filter for water leaks and tighten connections, bolts, nuts,

as required.

6. Note the initial pressure gauge reading when the filter is clean. (It will vary from pool to pool depending upon the pump and general piping

system.) As the filter removes dirt and impurities from the pool water, the accumulation of dirt in the filter will cause the pressure to rise

and diminish the water flow. When the pressure gauge reading is 1.5 bar, higher than the initial "clean" pressure you noted, it is time to

backwash the filter (see BACKWASH under filter and control valve functions).

NOTE: During initial clean-up of the pool water it may be necessary to backwash frequently due to the unusually

INSTALL/START-UP OF FILTER

heavy initial dirt load in the water.

REPLACEMENT PARTS OF MULTIPORT VALVE

DIMENSION TABLE

Model

High Diameter

845TP500 535

950TP650 635

Valve Port

Size Sand

145

1020TP700 710

210

Item Part No.

1 W88280105 40mm Top Mount Valve

2 W89280101 40mm Union With Sight Glass, O-Ring

3 W89280102 40mm Union Set (2 Pieces) With O-Ring

W06021001 Plastic Pressure Gauge With O-Ring (35psi)

W01111048 Connector for Pressure Gauge/Stopper

W89010119 M6*50 Screws With Nut

W01271010 Clamp Lock

6 W02011134 O-Ring for Filter Neck

W01331008 TP500 Filter Tank

W01331010 TP650 Filter Tank

W01331009 TP700 Filter Tank

W89011605 TP500 Lateral Assembly with Center Pipe

W89011606 TP650 Lateral Assembly with Center Pipe

W89011607 TP700 Lateral Assembly with Center Pipe

9 W01172008 TP500-TP700 Laterals (126mm)

10 W89011601 Water Drain Set

11 W01111062 TP500-TP700 Filter Base

Description

Item Part No. Des cription

1 W01013003 Handle(Big)

2 W03018008 Pin for Handle

3 W01181001 Washer for Handle

4 W89280107 M6×30 Screw with Nut for Standard Lid

5 W01013004 40mm Top Mount Valve Standard Lid (Black)

6 W02011002 O-Ring for 40mm Valve Lid

7 W01181002 Washer for Spring

8 W03014001 Spring for 40mm Top Mount Valve

9 W02011022 O-Ring for 40mm Valve Rotor

10 W01021001 40mm Valve Rotor

11 W02311002 Spider Gasket

12 W01013007 40mm Top Mount Valve Bottom Body Clamp（black)

13 W01013011 40mm Diffuser

14 W02011001 O-Ring for Diffuser

15 W01013012 40mm Top Mount Valve Over Drain Diffuser

16 W02011134 O-Ring

17 W02011151 O-Ring for 40mm Connector

18 W01013015 40mm Connector (black)

19 W02011003 O-Ring for 40mm Union

20 W01171153 40mm Union (A/E)

21 W01013017 40mm Union Nut (black)

22 W01041002 40mm Union With Sight Glas s (short)

23 W01172026 40mm Union With Sight Glas s Holder

24 W01111048 Connector for pres sure gauge/stopper

25 W89021703 Drain Plug with O-ring

26 W06011009 Oil Pressure Gauge With O-ring (50Psi)

Especificaciones del producto

Marca:	Zodiac
Categoría:	filtro de agua
Modelo:	TP500
Colocación del dispositivo:	Ingebouwd
Tipo de operación:	Draaiknop
Color del producto:	Zwart
Pantalla incorporada:	Nee
Temporizador:	Nee
Peso.:	7500 g
Ancho:	590 mm
Profundidad:	510 mm
Altura:	47 mm
Longitud del cable:	0.85 m
Peso del embalaje:	8000 g
Ancho del embalaje:	670 mm
Empaquetadura en profundidad:	595 mm
Altura del embalaje:	160 mm
Potencia quemador/zona de cocción 2:	3500 W
Potencia quemador/zona de cocción 3:	1650 W
Potencia quemador/zona de cocción 1:	1650 W
Número de quemadores/zonas de cocción:	4 zone(s)
tipo de placa:	Gaskookplaat
Ignición electrónica:	Ja
Quemador/zona de cocción tipo 1:	Regulier
Quemador/zona de cocción tipo 2:	Groot
Tipo de quemador/zona de cocción 3:	Regulier
Número de quemadores de gas:	4 zone(s)
Número de zonas de cocción electrónicas:	0 zone(s)
Quemador normal/zona de cocción:	- W
Posición de control:	Boven voorzijde
Carga conectada (eléctrica):	0 W
Ancho del compartimento de instalación:	560 mm
Profundidad del compartimento de instalación:	480 mm
Altura del compartimento de instalación:	40 mm
Actual:	0.2 A
Carga conectada (gas):	7800 W
Protección del sensor de calor:	Ja
Indicador de calor residual:	Nee
Altura bajo encimera:	7 mm
Tipo de quemador/zona de cocción 4:	Sudderen
Potencia quemador/zona de cocción 4:	1000 W
Fuente de alimentación quemador/zona de cocción 1:	Gas
Fuente de alimentación quemador/zona de cocción 2:	Gas
Fuente de alimentación quemador/zona de cocción 3:	Gas
Fuente de alimentación del quemador/zona de cocción 4:	Gas
Posición del quemador/zona de cocción 1:	Links voor
Posición quemador/zona de cocción 2:	Links achter
Posición quemador/zona de cocción 3:	Rechts achter
Posición del quemador/zona de cocción 4:	Rechts voor
Forma zona de cocción 1:	Rond
Forma zona de cocción 2:	Rond
Forma zona de cocción 3:	Rond
Forma zona de cocción 4:	Rond
Placa de cubierta:	Nee