AFX Shaw SHAL054840LAJMV Manual de Usario

AFX Alivio Shaw SHAL054840LAJMV

Lee a continuación 📖 el manual en español para AFX Shaw SHAL054840LAJMV (1 páginas) en la categoría Alivio. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/1
LED door Luminaires In
Ceiling Mount
120 277- VAC 60Hz/
Page 1 of 1 R0 8061530
Model #: SHAL052220LAJMV
SHAL054840LAJMV
Limited Factory Warranty
AFX Inc. hereby warrants that this xture is free from defects in materials and workmanship when installed and used under normal operating conditions for a period of 5 years
from date of purchase. This warranty covers all component parts and extends only to replacement of defective xture or components; it does not cover failure due to improper
installation, misuse, mishandling or damage incurred in transit.
View shown for reference
only. Individual models
may vary.
Safety Precautions
Read all safety precautions and installation instructions carefully before installing or servicing thisxture. Failure to comply with these instructions could result in potentially fatal electric shock and/or
property damage.
is recommended that a qualied electrician perform all wiring. This xture must be wired in accordance with all national and local electrical codes. It
Do not handle any energized xture or attempt to energize any xture with wet hands or while standing on a wet or damp surface or in water.
This xture is designed for use in a 120- VAC / 60Hz circuit. This xture is not compatible on dimming circuit. 277
Make sure that the power source conforms to the requirements of the xture. (See labels on the xture housing).
To reduce the risk of electrical shock, and to assure proper operation, this xture must be adequately grounded. To accomplish proper grounding, there must be a separate ground wire (green)
contact between thisxture and the ground connection of your main power supply panel.
This xture is intended to be used for general indoor lighting in dry or damp locations.
Disclaimer
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and Canadian ICES-005 (B) / NMB-005 (B). These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiver antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult with the dealer or an experienced radio/TV technician for help.
Any modications to this xture may void the warranty and interfere with the safe operation of the luminaire.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Assembly Instructions
Step 1 Preparing for installation–
A. at fuse or circuit breaker box before installing or servicing any part of Disconnect electrical power
this xture.
B. Carefully remove the xture from the carton, remove components from hardware kit.
C. Remove diuser (5) from xture (1) by gently pull away then set it aside until ready to be
reinstalled.
D. Position the xture (1) onto the ceiling aligning with junction box (not included) use pencil to and
mark four mounting locations for drywall anchors. Take the xture (1) down and punch a small hole
in the ceiling at each of the locations using a nail to see if there is a wood stud to mount the xture
to. Where there is a wood stud, use a suitable screw (3) to mount the xture. Where there is no
stud to screw into, a drywall anchor or toggle bolt (4) must be used to mount the xture securely to
the ceiling.
E. Pull the power supply wires down into the xture. through an Ø1/2” hole
F. Install the xture to the ceiling using four wood screws (3) and two screws (2) to secure it.
Wiring All wiring must take place inside junction box (not included) –
Caution: Make sure power is o at fuse or circuit breaker box. Check power wires for damage or
scrapes. If power supply wires are within three inches of the LED driver, use wire suitable for at
least 90°C (194°F). Most dwellings built before 1985 have supply wire rated to 60°C. Consult Note:
a qualied electrician to ensure correct branch circuit conductor before installing.
Step 2 Wiring xture –
A. Make all wire connections to appropriate wire. Secure with wire nuts (provided).
B. Connect the green wire from the xture to the supply power source ground wire.
C. Connect the white wire from the xture to the white (N) wire from supply power source.
D. Connect the black xture wire to the black (L) wire from supply power sourc e.
E. Pull on each wire lead to make sure connections are secure. Make certain no Do not mix wires.
bare wires are exposed outside of wire connectors. Tuck all connections neatly into the junction
box.
Step 3 Color changing temperature adjustment, CCT (if desired) –
A. Adjust CCT switch on the board according to the desired color temperature as shown below. Note:
Fixture is preset to 3000K from factory.
Step 4 Install Diffuser –
A. Insert diuser (5) groove to long edge of the xture (1) one side rst then gently push the other side with thumb until
diuser groove is captivated and ush with the xture to secure it.
Step 5 Restore power at fuse or circuit breaker box –

Especificaciones del producto

Marca: AFX
Categoría: Alivio
Modelo: Shaw SHAL054840LAJMV

¿Necesitas ayuda?

Si necesitas ayuda con AFX Shaw SHAL054840LAJMV haz una pregunta a continuación y otros usuarios te responderán


Alivio AFX Manuales

AFX

AFX Grace GRCP07CBBK Manual de Usario

12 Octubre 2024
AFX

AFX Point PNTP0107L30D1BK Manual de Usario

12 Octubre 2024
AFX

AFX Marquette MQTB3840L30ENWN Manual de Usario

25 Septiembre 2024
AFX

AFX Reeves RVEF1624LAJUDSNLW Manual de Usario

25 Septiembre 2024
AFX

AFX Arlo ARLS050407L35MVSN Manual de Usario

25 Septiembre 2024
AFX

AFX Grace GRCC14CBBK Manual de Usario

25 Septiembre 2024
AFX

AFX Plaza PLZS11MBBN Manual de Usario

25 Septiembre 2024
AFX

AFX Shaw SHAL054840LAJMV Manual de Usario

25 Septiembre 2024
AFX

AFX Ryland RYDV280422L30D2SN Manual de Usario

25 Septiembre 2024
AFX

AFX Novara NVS5131200L30D1SN Manual de Usario

25 Septiembre 2024

Alivio Manuales

Últimos Alivio Manuales

Ansmann

Ansmann FL4500AC Manual de Usario

27 Octubre 2024
Brennenstuhl

Brennenstuhl 1171250801 Manual de Usario

27 Octubre 2024
Steinel

Steinel FRS 30 Manual de Usario

27 Octubre 2024
Stairville

Stairville DMX Invader 2420 MK II Manual de Usario

27 Octubre 2024
Aqara

Aqara LED Light Bulb (Tunable White) Manual de Usario

26 Octubre 2024
V-Tac

V-Tac VT-7959 Manual de Usario

26 Octubre 2024
Quoizel

Quoizel Latitude LTT1628EK Manual de Usario

25 Octubre 2024
Elan

Elan Osk 83765 Manual de Usario

25 Octubre 2024
ET2

ET2 Fizz III E22757-89PC Manual de Usario

23 Octubre 2024
Crystorama

Crystorama Colton COL-102-AG Manual de Usario

23 Octubre 2024