Altronix ReServ 1WPV Manual de Usario
Altronix
Unión Postal Universal
ReServ 1WPV
Lee a continuación 📖 el manual en español para Altronix ReServ 1WPV (8 páginas) en la categoría Unión Postal Universal. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/8
Outdoor Video Surveillance UPS
Installation Guide
Models Include:
ReServ1WPV
- Twelve (12) true sine wave regulated 24VAC outputs
and Four (4) regulated 12VDC outputs.
- 4 amp total supply current @ 24VAC and 2 amp total supply current @ 12VDC.
- PTC protected power-limited outputs.
ReServ2WPV
- Sixteen (16) true sine wave regulated 24VAC outputs.
- 4 amp total supply current.
- PTC protected power-limited outputs.
ReServ3WPV
- Sixteen (16) regulated 12VDC outputs.
- 8 amp total supply current.
- PTC protected power-limited outputs.
More than just power.™
- 2 - ReServWPV
Overview:
ReServWPV Outdoor Video Surveillance UPS units are designed to provide power for 24VAC and/or 12VDC cameras
during normal or power outage conditions. True sine wave regulated AC outputs and/or regulated DC outputs.
ReServWPV Series Outdoor Video Surveillance UPS Configuration Reference Chart:
Altronix
Model Number
Output/Supply
Current (Amp
Ambient
Temperature Input Rating
PTC
Protected
Power-
Limited
Outputs
24VAC
Outputs
12VDC
Outputs
ReServ1WPV
24VAC @ 4 amp (100VA)
and 12VDC @ 2 amp -33º - 30º C 220VAC 50Hz,
2 amp 16 12 4
24VAC @ 3.5 amp (85VA)
and 12VDC @ 2 amp -33º - 42º C
ReServ2WPV 24VAC @ 4 amp (100VA) -33º - 30º C 220VAC 50Hz,
2 amp 16 16 ----
24VAC @ 3.5 amp (85VA) -33º - 42º C
ReServ3WPV 12VDC @ 8 amp -33º - 42º C 220VAC 50Hz,
2 amp 16 16----
Specifications:
Stand-by Specifications:
Stand-by Batteries
ReServ1WPV - 4 amp (100VA) load at 24VAC and 2 amp load at 12VDC max.
ReServ2WPV - 4 amp (100VA) max. load at 24VAC
ReServ3WPV - 8 amp (100VA) max. load at 12VDC
Two (2) 12VDC/7AH 45 minutes
Two (2) 12VDC/12AH 90 minutes
Installation Instructions:
This installation should be made by qualified service personnel and should conform to all local codes and in accordance
with the National Electrical Code. This product contains no serviceable parts.
1. Remove back plate inside the enclosure by removing the four (4) mounting screws.
2. Mark and drill desired knockouts on the enclosure to facilitate wiring .(Fig. 1, pg. 3)
It is required to use UL Listed outdoor rated conduit hubs with a minimum outdoor rating of 4X.Note:
3. Secure back plate inside enclosure with the four (4) mounting screws.
4. Mark and drill holes that line up with the top and bottom holes of the enclosure flange Mount unit in the desired
location with the appropriate fasteners . Secure enclosure to earth ground. (Pgs. 7 and 8)
This product needs to be secured to the building/pole before operation.Note:
5. Connect AC power mains to the terminals marked [L] and [N] .(Figs. 2-3, pg. 5-6)
Use 18 AWG or larger for all power connections (Battery, output) .(Figs. 2-3, pg. 5-6)
Use 18 AWG to 22 AWG for power limited circuits (AC Fail/Low Battery reporting) .(Figs. 2-3, pg. 5-6)
A readily accessible disconnect device shall be incorporated in the building installation wiring.Note:
6. The LEDs on the power supply board will illuminate when AC power is present.
7. Measure output voltage before connecting cameras/devices to outputs. This helps avoiding potential damage.
Output:
• PTC protected power-limited outputs are rated @ 1 amp.
Battery Backup:
• Built-in charger for sealed lead acid or gel type batteries.
• Automatic switchover to stand-by battery when AC fails.
Supervision:
• AC fail supervision (form “C” contacts).
• Low battery supervision (form “C” contacts).
Visual and Audio Indicators:
• AC/DC power LED indicators.
• Individual power output LED indicators.
• Low voltage input and Shutdown LED indicators.
• Audio AC Fail and Battery Fail indicator.
Additional Features:
• True sine wave regulated AC outputs (ReServ1WPV and
ReServ2WPV). Regulated DC outputs (ReServ1WPV and
ReServ3WPV).
• Unit maintains camera synchronization.
• Ease of installation saves time and eliminates costly labor.
Enclosure Dimensions:
• NEMA4 / IP66 Rated enclosure.
• Accommodates up to two (2) 12VDC/7AH batteries or
two (2) 12VDC/12AH batteries.
17.375” x 12” x 6.5” (441.3mm x 304.8mm x 165.1mm)
ReServWPV - 3 -
8. ReServ3WPV only - Adjust voltage for every two (2) outputs using the corresponding trimpot(s) on the board prior
to connecting devices.
9. Connecting cameras/devices:
- Connect 12VDC cameras/devices to terminals marked [P 1-4, N 1-4] .ReServ1WPV (Fig. 2, pg. 5)
Connect 24VAC cameras/devices to terminals marked [5-16] .(Fig. 2, pg. 5)
- Connect 24VAC cameras/devices to terminals marked [1-16] .ReServ2WPV (Fig. 2, pg. 5)
- Connect 12VDC cameras/devices to terminals marked [P 1-16, N 1-16] .ReServ3WPV (Fig. 3, pg. 6)
10. Connect batteries to the terminals marked [-- BAT + ] . Use two (2) 12VDC batteries connected in (Figs. 1-3, pg. 5-7)
series for 24VDC operation (battery leads included).
Use batteries - Casil CA1270 (12V/7AH), Genesis NP7-12 (12V/7AH) or NP7-12 (12V/12AH), Ultratech UT1270
(12V/7AH) or Ultratech UT12120 (12V/12AH).
11. Connect appropriate signaling notification devices to AC FAIL and BAT FAIL (Figs. 2-3, pg. 5-6)
supervisory relay outputs.
12. The power LEDs on the unit for Outputs 1-16 will illuminate when AC power is present . (Figs. 2-3, pg. 5-6)
If any of the power LEDs are not illuminated, the cause may be due to the following:Note:
a. AC mains and battery fail.
b. One (1) or more power output PTCs are tripped due to a short circuit or overload condition.
c. Unit damaged/defective.
To reset the PTC:
1. Disconnect corresponding camera/device connected to terminals marked [1-16] .(Figs. 2-3, pg. 5-6)
2. Eliminate the trouble condition (short circuit or overload).
3. Allow 1 minute for PTC to cool off (reset).
4. Connect corresponding cameras/devices to terminals marked [1-16] .(Figs. 2-3, pg. 5-6)
5. Power LEDs will illuminate indicating power has been restored to outputs .(Figs. 2-3, pg. 5-6)
WARNING: This installation should be made by qualified service personnel and should conform to the
National Electrical Code and all local codes.
Right PanelLeft Panel
Suggested Locations
for Wire Entries
Bottom Panel
Fig. 1
Especificaciones del producto
| Marca: | Altronix |
| Categoría: | Unión Postal Universal |
| Modelo: | ReServ 1WPV |
¿Necesitas ayuda?
Si necesitas ayuda con Altronix ReServ 1WPV haz una pregunta a continuación y otros usuarios te responderán
Unión Postal Universal Altronix Manuales
11 Septiembre 2024
11 Septiembre 2024
11 Septiembre 2024
11 Septiembre 2024
11 Septiembre 2024
Unión Postal Universal Manuales
- Unión Postal Universal AEG
- Unión Postal Universal IKEA
- Unión Postal Universal HP
- Unión Postal Universal Apc
- Unión Postal Universal Lenovo
- Unión Postal Universal Tripp Lite
- Unión Postal Universal Energenie
- Unión Postal Universal Voltcraft
- Unión Postal Universal Adj
- Unión Postal Universal Digitus
- Unión Postal Universal LevelOne
- Unión Postal Universal Eaton
- Unión Postal Universal CyberPower
- Unión Postal Universal Block
- Unión Postal Universal Avocent
- Unión Postal Universal Minuteman
- Unión Postal Universal Maruson
- Unión Postal Universal V7
- Unión Postal Universal Phoenix Contact
- Unión Postal Universal Puls Dimension
- Unión Postal Universal Salicru
- Unión Postal Universal Equip
- Unión Postal Universal Murr Elektronik
- Unión Postal Universal Ditek
- Unión Postal Universal Bxterra
- Unión Postal Universal Middle Atlantic
- Unión Postal Universal FSP
- Unión Postal Universal Atlantis Land
- Unión Postal Universal PowerWalker
- Unión Postal Universal FSP/Fortron
- Unión Postal Universal Online USV
Últimos Unión Postal Universal Manuales
24 Octubre 2024
22 Octubre 2024
22 Octubre 2024
22 Octubre 2024
20 Octubre 2024
18 Octubre 2024
18 Octubre 2024
12 Octubre 2024
12 Octubre 2024
12 Octubre 2024