AMX MIO-R1-AUDIO Manual de Usario

AMX Mando a distancia MIO-R1-AUDIO

Lee a continuación 📖 el manual en español para AMX MIO-R1-AUDIO (2 páginas) en la categoría Mando a distancia. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

Quick Start Guide

MIO R-1 AUDIO Tango Distributed Audio Remote Control

Overview

The MIO R-1 AUDIO (FG147-04) remote provides custom control features, contained

in an elegant handheld device, designed specifically for use with Matrix Distributed

Audio Systems using Metreau DAS-MET-6SRC keypads.

The MIO R-1 AUDIO controls up to 8 different devices or Sources.

Specifications

Installing Custom Buttons

1. Flip and turn the MIO R-1 AUDIO so that the buttons are facing away from you

and the device is upside down.

2. Holding the device in both hands, place your thumbs on the battery door and

push up to slide the battery door free.

3. Unscrew the 6 screw points indicated in FIG. 2.

4. Turn the unit over so the buttons are facing you.

5. Lift the top assembly away from the PCB.

6. If necessary, push out the standard buttons from the front of the top assembly.

7. Drop on your custom button pad and verify the alignment with the guide posts on

the PCB.

8. Place the top assembly back down on the PCB and return the unit over, expos-

ing the 6 screw points.

9. Tighten the 6 screw points.

10. Place the battery door back on the device, slide to lock it in place.

Inserting Batteries into The MIO R-1 AUDIO

To install your 4 AAA batteries into the MIO R-1 AUDIO:

1. Flip and turn the MIO R-1 AUDIO so that the buttons are facing away from you

and the device is upside down.

2. Holding the device in both hands, place your thumbs on the battery door and

slide the battery door free.

3. Insert the batteries as indicated inside the battery compartment.

4. Place the battery door back on the device, slide to lock it in place.

Battery Low Indicator

When the battery charge level is too low to sustain continuous operation, the LCD

flashes, "Battery Low" and the device shuts down.

Programming The MIO R-1 AUDIO Using KeypadBuilder

The MIO R-1 AUDIO comes pre-customized with appropriate labels, which in most

cases should not be changed. However, if in your installation you intend to use the

MIO R-1 AUDIO with a NetLinx Controller and Metreau AxLink keypads (for more than

just Audio), you could customize your buttons in the KeypadBuilder application. The

application and documentation are available from www.amx.com.

There are a select number of Serial Commands the MIO R-1 AUDIO recognizes. For a

full list and descriptions, consult the MIO R-1 AUDIO Operation/Reference Guide.

The Programming Jack is used for communication between the device and

KeypadBuilder. The programming jack uses a three-wire, 2.5 mm stereo jack, you can

order the programming cable (FG10-817) from AMX if you do not currently possess

one. While loading your configuration file make sure the device is situated as such that

the batteries will not fall out. The load will fail if your batteries fall out during the

process. The MIO communicates at 115200 baud rate.

Refer to the MIO R-1 AUDIO Operation/Reference Guide for instructions on using the

Programming Jack to load configuration files on the MIO R-1 AUDIO.

Tone Control & SRS Setting

To access the Tone Control and SRS settings, press the TONE button. This enables

the Tone Control Mode with BASS as the first mode selected. There are 3 Tone

Control Modes available for adjustment, and 4 SRS options, as follows:

• BASS: Increase / Decrease from -10dB to +10dB (Up/Down NAV buttons)

• Treble: Increase / Decrease from -10dB to +10dB (Up/Down NAV buttons)

• Balance: Left / Right (Up NAV button = right, Down NAV button = left)

• SRS options: BASS Boost, Focus, 3D, WOW

The Source buttons on the Metreau keypad provides visual feedback as to which

mode it is currently in. The following sources will light based on the current mode:

• Source 1 = BASS

• Source 2 = Treble

• Source 3 = Balance

• Source 4 = SRS

When first entering Tone Control Mode, BASS mode is active (Source 1 LED is lit). To

move from mode to mode, select the Center NAV button. This saves the setting and

moves to the next mode.

FIG. 1 MIO R-1 AUDIO remote controller

MIO R-1 AUDIO Specifications

Power Requirements: 4 AAA Alkaline Batteries (included) - approx. 5 hours battery life

Transmission

Frequencies

AMX 38 KHz/455 KHz IR

Note: The Metreau MET-6N keypads only support 38 KHz. When used

with MET-6N keypads, the MIO R-1 AUDIO must be set to 38 KHz.

Transmission

Range (distance)

with MIO IR Receiver

• 100 feet at 38KHz

• 50 feet at 455KHz

Transmission

Range (angle)

• 140 degrees (+/-70° from perpendicular) horizontally from an axis

extending from the end of the remote.

• 40 degrees (+/-20° from perpendicular) vertically from an axis

extending from the end of the remote.

Top Components • LED - blue backlit buttons indicate device is awake

• Display (OLED) - 128 x 32 pixels, active area is 29.42mm x 7.98mm

• Pushbuttons - the power button is red backlit; the rest are blue backlit

buttons. 45 buttons; 9 custom buttons (3 macro and 6 device).

Rear Component • Programming Port - 2.5 mm stereo female conductor jack

• Battery Door

Dimensions (HWD) 9.50 x 2.00 x .74 (241.3 mm x 50.8 mm x 18.80 mm)

Weight • .45 lbs (20 kg) without batteries

• .55 lbs (25 kg) with batteries

Operating Environment: • Operating Temperature: 0° to 50° C (32° to 122° F)

• Storage Temperature: -10° to 70° C (14° to 158° F)

Included Accessories: • 4 AAA Batteries

Other AMX Equipment • DB-9 extension cable (FG10-727)

• Programming Cable - a 3 wire, 2.5 mm stereo jack (FG10-817)

• Custom engraving (FG147-01)

• MIO-RCC Kit (FG147-03K)

• MIO-RCC Charging Base (FG147-02)

• MIO-RBP Rechargeable Lithium Ion Battery (FG147-10)

• MIO Modero IR Receiver (FG5797-01xx; xx indicates color)

Power

IR Transmitting

Battery Meter

Source Select Options

2 3

4 5

8 910

26 28

44 45

Numeral Keypad

1 - Power

2 - Alarm

3 - Favorite

4 - Privacy

5 - Lock

6 - NAV Up

7 - NAV Down

8 - NAV Left

9 - NAV Right

10 - NAV Center

11 - Volume Up

12 - Volume Down

13 - NAV Up

14 - NAV Down

15 - Group

16 - Preset

26 - “ • “ (dot)

28 - Enter

41 - NAV Left

42 - Tone Controls/SRS options

43 - NAV Right

44 - NAV Up

45 - NAV Down

38 - Configuration (press and

hold with the “Dot” button (#26)

to access Configuration options)

FIG. 2 6 screwpoints (battery compartment cover removed)

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

2/08

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-0147-04 REV: A

Note: While in each of the modes, press and hold the Center NAV button to return to

the default for that mode.

SRS (Bass Boost, Focus, 3D and WOW) Settings

Use the UP Nav button to cycle through the SRS Settings: BASS Boost, Focus, 3D,

WOW (in that order).

Use the Down NAV button to cycle backwards to the previous SRS setting.

• Press and hold the Center NAV button to disengage/clear the SRS settings

(none of the SRS modes will be engaged).

• Press the Center NAV button to save SRS Mode & exit from Tone Control

set-up.

Only one SRS mode can be engaged per room/zone. Each room/zone, however,

can have a different SRS mode.

The Volume LED's are used to provide feedback as to which SRS setting is active:

• No LED = SRS Off

• LED1 = BASS boost

• LED 1&2 =Focus

• LED 1,2&3 =3D

• LED 1,2,3&4 =WOW

Moving from one SRS position to another disengages the original setting i.e. moving

from WOW to BASS BOOST, disengages WOW.

Zone Control

•To turn a single Zone ON, press any Source button (or press the Power

Button).

Note: If the Power button is pressed, the zone will turn ON and will remember

which source was previously ON.

•To turn a single Zone OFF, press the Power button.

•To turn a specific Source ON in all Zones, press and hold any Source button

(the selected source will turn on and play in all zones).

•To turn a specific Source OFF in all Zones, press and hold the active Source

button.

•To Turn All Zones OFF (System OFF), Press the "OFF" button. All zones will

be turned off, and no sources will play.

Note: One minute after an ALL OFF has been performed, the Controller and all

Sources will be powered down

Note: Pressing Source Buttons switches between sources and turns the

Source On, but does not toggle between ON and OFF.

Source Control

The source control functionality outlined below represents "suggested" functions. All

source control buttons (Up, Down, Left, Right, Center and Center HOLD) can be

customized via the Controller Menu for all sources except for the Internal Tuner,

which cannot be customized.

Internal Tuner and Audio Server

CD and DVD

Satellite and Other

Custom XM

Direct Numeric Access

Tuners

Enter the station identification and press ENTER.

• Strings of 3 to 4 numbers are recognized.

• If a " • " (dot) is part of the string, then an FM station is assumed, otherwise an

AM station is assumed.

Example: 1050 + ENTER= 1050AM, 104 • 5 + ENTER = 104.5FM

CD Player / Changer

To select a specific Disc & Track, the format is DDD • TTT + ENTER

(DDD=Disc, TTT=Track).

Example: 11.11 + ENTER = Disc 11, Track 11

To select a specific track on the current disk, enter TTT + ENTER (TTT=Track).

Example: 3 + ENTER = current disk, Track 3

Satellite Radio/Video

Enter the station number and press ENTER. Strings of 2 - 4 numbers are recognized.

Configuration Mode

The configuration mode allows you to set various device features (IR Transmit Mode,

Timeout Adjustment, Download Mode, Debug Mode, Battery Type, LED Awake

Brightness, and LED Sleep Brightness.

To enter Configuration Mode:

1. Press and hold button #38 and the "." (dot) or button #26 (see FIG. 1). Both

buttons must be pressed within 0.1 seconds of each other and held down for 2

seconds. The device indicates you are now in configuration mode.

2. Press button #3 (FAV) when you are finished.

Note: Your settings will not be lost in the event your batteries die or are removed.

IR Transmit Mode

Note: Metreau MET-6N keypads support 38KHz only. The MIO R-1 AUDIO must be

set to 38KHz if used with MET-6N keypads.

Pressing button 1 toggles the IR transmission mode between 38KHz (default) and

455KHz. The display indicates the current mode.

Timeout Adjustment

Press button 2 to change the sleep timeout from the default. Each time "2" is

pressed, the sleep timeout raises incrementally. The pre-determined sleep timeouts

are:3 seconds, 6 seconds, 9 seconds, and 12 seconds. The display indicates the

selected sleep timeout.

Download Mode

Pressing button 3 toggles the Download mode OFF and ON. The Download mode

must be ON before you can download a file to the MIO R-1 AUDIO device. While the

Download mode is ON the device will not go to sleep. A power cycle will return the

device to Download OFF.

Debug Mode

Pressing button 4 toggles development mode between ON and OFF. The display

indicates the selected mode. In development mode, the display shows the IR code

assigned to buttons when pressed.

This mode is useful to the programmer when determining what IR codes are

associated to each mode.

Battery Type

Pressing button 6 toggles the battery type between Normal and Recharge. The

display indicates the selected type. The type of battery in the MIO R-1 AUDIO

dictates the battery type you need to set.

LED Awake Brightness

Pressing button 7 toggles the Power LED brightness mode from LOW to MED and

then HIGH. The display indicates the selected mode.

LED Sleep Mode Brightness

Pressing button 8 toggles the Sleep brightness mode from OFF to LOW and then

MED. The Sleep brightness is the state the MIO R-1 AUDIO assumes while in the

charging cradle.

Additional Documentation

Refer to the MIO R-1 AUDIO Remote Operation/Reference Guide for additional

information on MIO R-1 AUDIO functionality, including: Privacy Mode, Presets, Zone

Grouping, Favorites, Alarm, and Keypad Lockout.

NAV Button Internal Tuner AUDIO SERVER

NAV Up SEEK UP NEXT

NAV Down SEEK DOWN PREVIOUS

NAV Left Prev PRESET Prev PAGE

NAV Right Next PRESET Next PAGE

NAV Center (press) AM/FM SELECT

NAV Center (press/hold) Stereo/Mono User Defined 1

NAV Button CD DVD

NAV Up Next TRACK UP

NAV Down Prev TRACK DOWN

NAV Left Prev DISC LEFT

NAV Right Next DISC Right

NAV Center (press) User Defined1 Select

NAV Center (press/hold) User Defined2 Menu

NAV Button External Satellite Other

NAV Up Next Channel User Def UP

NAV Down Prev Channel User Def DOWN

NAV Left Guide Down User Def LEFT

NAV Right Guide UP User Def RIGHT

NAV Center (press) Select User Def SELECT

NAV Center (press/hold) Guide User Def HOLD SELECT

NAV Button CUSTOM XM

NAV Up UP

NAV Down DOWN

NAV Left LEFT

NAV Right RIGHT

NAV Center (press) CENTER

NAV Center (press/hold) CEN hold

Especificaciones del producto

Marca:	AMX
Categoría:	Mando a distancia
Modelo:	MIO-R1-AUDIO

¿Necesitas ayuda?

Si necesitas ayuda con AMX MIO-R1-AUDIO haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

Mando a distancia AMX Manuales

AMX FG1311-16-KW Manual de Usario

8 Septiembre 2024

AMX CP-1016-TR-UK Manual de Usario

8 Septiembre 2024

AMX MIO-R4 Manual de Usario

8 Septiembre 2024

AMX MIO-CLASSIC-S Manual de Usario

8 Septiembre 2024

AMX MIO-CLASSIC-D Manual de Usario

8 Septiembre 2024

AMX MIO-PRESTIGE-S Manual de Usario

8 Septiembre 2024

AMX MIO-R1-AUDIO Manual de Usario

8 Septiembre 2024

Mando a distancia Manuales

Últimos Mando a distancia Manuales

Monacor DRM-880WP Manual de Usario

27 Octubre 2024

Hama Spot-Pointer V2 Manual de Usario

26 Octubre 2024

Sony RM-ED022 Manual de Usario

21 Octubre 2024

Sonos Control Manual de Usario

18 Octubre 2024

One For All URC 7935 Manual de Usario

18 Octubre 2024

Canon BG-E20 Manual de Usario

12 Octubre 2024

Neewer RT112 Manual de Usario

8 Octubre 2024

Neewer RT113 Manual de Usario

8 Octubre 2024

Logitech Harmony 785 Manual de Usario

8 Octubre 2024

DSC WS4949 Manual de Usario

8 Octubre 2024