Atdec TH-1030-VFM Manual de Usario

Atdec soporte de panel plano TH-1030-VFM

Lee a continuación 📖 el manual en español para Atdec TH-1030-VFM (4 páginas) en la categoría soporte de panel plano. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

Step 7. Final Adjustment

Installation Complete

Your Telehook Wall Mount Swing Arm is complete and ready to use.

Position and angle your Display as desired, ensuring the Swing Arm moves freely.

Adjust the tension of the joints to suit, using the Allen Keys supplied.

4mm Allen Key

6mm Allen Key

As Display Manufacturers are constantly releasing new monitor models, Atdec does not accept responsibility if the VESA mounting does not comply with the international standards.

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 27.11.09 ©

LOOSEN

T GHTENI

LOOSEN T GHTENI

Step 6. Cable Management

127( Leave enough

slack in the cables to

allow for full movement.

Connect cables

Cable Cover (x2)

Cable Clip

To utilise the Telehook Swing Arm cable

management system, use the Cable Covers

and Cable Clip as shown.

IM A I F MA IPORT NT N OR T ON

,03257$17,QVWDOO7HOHKRRN:DOO0RXQW6ZLQJ$UPDVSHU ,QVWDOODWLRQ,QVWUXFWLRQVWKH

! Telehook Wall Mount Swing Arm supports displays weighing up to 20kg (44lbs), with VESA hole configurations:

75x75mm (3”x3”), 100x100mm (4”x4”), *200x100mm (8”x4”), and *200x200mm (8”x8”) (*using extension tabs supplied)

! The Manufacturer accepts no responsibility for incorrect installation.

Step 1. Check Components

Check you have received all parts against the Component Checklist and Hardware above.

Step 2. Installing the Wall Bracket

Component Checklist

Stud

Masonry Wall

Nylon Anchor (x2)

Wall Mount

Screw (x2)

Wall Mount

Screw (x2)

Wall Material

H ward are

Flat Screen Wall Mount | Swing Arm

Installation Instructions

TOOL RE RES QUI D:

Power Drill

4mm ( 5/32”) Drill Bit

11mm ( 7/16

”) Masonry Drill Bit

Phillips Head Screwdriver

Spirit Level

Mounting to a Mounting to a 7LPEHU6WXG:DOO 0DVRQU\:DOO:

7+9)0

Swing Arm

Vesa Plate

- Position the Wall Bracket vertically on the wall and mark the

2 mounting holes (use a spirit level to check).

- Drill two 60mm (23/8“) deep holes using an 11mm (7/16”)

masonry drill bit.

- Secure the Wall Bracket using the Wall Mount Screws and

Nylon Anchors supplied.

- Position Wall Bracket vertically on the wall and mark the

2 mounting holes (use a spirit level to check).

- Drill two 60mm (23/8”) deep holes using a 4mm (5/32 ”) drill bit.

- Secure the Wall Bracket using the Wall Mount Screws supplied.

2.5mm Allen Key

4mm Allen Key

5mm Allen Key

6mm Allen Key

Washer (x4)

Nylon Anchor (x2)

Wall Mount Screw (x2)

Wall Bracket

Extension

Tabs (x4)

E wxtension Mounting Scre s

M4x12mm/M4x16mm (x4 each)

M5x12mm/M5x16mm (x4 each)

M6x12mm/M6x16mm (x4 each)

Display Mounting Scre sw

M5x12mm (x4)

75 or 100mm

VESA

Top of

Display

Ste 4. Att ch the VESA te t ur p a pla o yo Display

Fasten the VESA plate to your Display using the Display Mounting screws and Washers provided.

Select the appropriate size screw to suit your Display.

Display Mounting Screw (x4)

Top of VESA plate

Washer (x4)

Display Mounting hole

Back of Display

Ste 3. Att ch the Exten n b t the VESA te p a sio Ta s o pla (optional)

Only use the Extension Tabs if the display you wish to mount has a 200x200mm (8”x8”),

or 200x100mm (8”x4”) VESA hole mounting configuration.

If not, skip to Step 4.

200mm (8”)

Secure the Extension Tabs to the VESA plate using

the M5x12mm Extension Mounting Screws supplied.

M5x12mm

Screw (x4)

Extension

Tab (x4)

VESA

plate

TIGHT NE

FIRMLY

OPTION - 200 200mm (8” 8”)A x x

200mm (8”)

OPTION B - 200 100mm (8” ”)x x4

100mm (4”) Extension

Tab (x4)

VESA

plate

M5x12mm

Screw (x4)

TIGHT NE

FIRMLY

NOTE: Position the Extension Tabs to

suit your display mounting hardware.

Large Hole

(M6-M8)

Small Hole

(M4-M5)

( required)

Ste 5. Att ch ur t the Sw ng Arp a yo Display o i m

Back of

Display

TIGHT NE

Tighten both grub screws with the

2.5mm Allen Key supplied.

Slot the VESA plate on to the Swing Arm.

Ensure the display is level,

using the horizontal

adjustment.

+/- °5

r t t no a io

5mm

Allen Key

Especificaciones del producto

Marca:	Atdec
Categoría:	soporte de panel plano
Modelo:	TH-1030-VFM
Peso.:	21500 g
Peso del embalaje:	24000 g
Ancho del embalaje:	660 mm
Empaquetadura en profundidad:	860 mm
Altura del embalaje:	330 mm
Altura (mín.):	1250 mm
Altura (máx.):	1330 mm
Ajustable en altura:	80 mm
El número de ruedas:	5 wiel(en)
Cantidad por paquete:	1 stuk(s)
Diseño ergonomico:	Ja
Fondo de color:	Zwart
Tipo-producto:	Gaming leunstoel
Ruedas:	Ja
Peso máximo del usuario:	150 kg
Soporte de espalda ajustable:	Ja
Altura del asiento ajustable:	Ja
Diámetro de empuñadura:	60 mm
Plataformas de juego compatibles:	Universeel
tipo de silla:	Gecapitonneerde zitting
Color del asiento:	Grijs
Tipo de respaldo:	Gecapitonneerde rugleuning
Color del respaldo:	Black, Grey, White
Brazo:	Ja
Reposabrazos ajustable:	Ja
Tipo de ajuste del reposabrazos:	1D-armleuning
almohada de apoyo para el cuello:	Ja
Incluye volante de carreras/modo vuelo:	Nee
Ancho-del-asiento:	530 mm
Profundidad-del-asiento:	570 mm
Cojín lumbar:	Ja
Altura del asiento (máx.):	530 mm
Altura del asiento (mín.):	450 mm
Material del respaldo:	Polyurethaan (PU)
Material del asiento:	Polyurethaan
Respirable:	Ja
Rango de ángulo del respaldo:	90 - 180 °
Clase de elevación de gas:	4
Altura-del-respaldo:	820 mm
Ancho del respaldo:	570 mm