Audio Pro DVD ONE Manual de Usario

Audio Pro No categorizado DVD ONE

Lee a continuación 📖 el manual en español para Audio Pro DVD ONE (25 páginas) en la categoría No categorizado. Esta guía fue útil para 13 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/25

(ENG) OPERATING INSTRUCTIONS

DVD ONE

2.1 DVD Receiver

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radia-

tors, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are pro-

vided for your safety. If the provided plug does not

fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience recepta-

cles, and the point where they exit from the appara-

tus.

11. Only use attachments/accessories specified by the

manufacturer.

12.

Use only with the cart, stand,

tripod, bracket, or table spec-

ified by the manufacturer, or

sold with the apparatus.

When a cart is used, use cau-

tion when moving the cart/

apparatus combination to

avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or

when unused for long periods of time.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate

normally, or has been dropped.

15. Damage Requiring Service

Unplug the apparatus from the wall outlet and refer

servicing to qualified service personnel under thee

following conditions:

A. When the power-supply cord or plug is dam-

aged,

B. If liquid has been spilled, or objects have fallen

into the apparatus,

C. If the apparatus has been exposed to rain or

water,

D. If the apparatus does not operate normally by

following the operating instructions. Adjust only

those controls that are covered by the operating

instructions as an improper adjustment of other

controls may result in damage and will often

require extensive work by a qualified technician

to restore the apparatus to its normal operation,

E. If the apparatus has been dropped or damaged in

any way, and

F. When the apparatus exhibits a distinct change in

performance this indicates a need for service.

16. Object and Liquid Entry

Never push objects of any kind into the apparatus

through openings as they may touch dangerous volt-

age points or short-out parts that could result in a

fire or electric shock.

The apparatus shall not be exposed to dripping or

splashing and no objects filled with liquids, such as

vases shall be placed on the apparatus.

Don’t put candles or other burning objects on top of

this unit.

17. Batteries

Always consider the environmental issues and fol-

low local regulations when disposing of batteries.

18. If you install the apparatus in a built-in installation,

such as a bookcase or rack, ensure that there is ade-

quate ventilation.

Leave 10 cm (4”) of free space at the top and sides

and 10 cm (4") at the rear. The rear edge of the shelf

or board above the apparatus shall be set 10 cm (4")

away from the rear panel or wall.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPARATUS

TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO

USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

AVIS

PORTABLE CART WARNING

S3125A

Precautions

1. Regional Restriction Codes (Region Number)

Regional restriction codes are built into DVD receivers and DVD

videos for each sales region. If the regional code of the DVD

receiver does not match one of the regional codes on the DVD

video, playback is not possible.

The regional number can be found on the rear panel of the DVD

receiver. (e.g. for Region 2)

2. About This Manual

This manual explains the basic procedures for operating the DVD

receiver. Some DVD videos do not support the full potential of

the DVD technology. Your DVD receiver may therefore not

respond to all operating commands. Refer to instruction notes on

discs.

A “ ” mark may appear on the TV screen during operation. It

means that the operation is not permitted by the DVD receiver or

the disc.

3. Recording Copyright

Recording of copyrighted material for other than personal use is

illegal without permission of the copyright holder.

4. AC FUSE

The fuse is located inside the chassis and is not user-serviceable.

If power does not come on, contact your Audio Pro authorized

service center.

5. Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME,

READ THE FOLLOWING SECTION CAREFULLY.

The voltage of the available power supply differs according to

country or region. Be sure that the power supply voltage of the

area where the unit will be used meets the required voltage (e.g.,

AC 230V 50 Hz) written on the rear panel.

6. Do not touch the unit with wet hands

Do not handle the unit or power cord when your hands are wet or

damp. If water or any other liquid enters the case, take the unit to

an authorized service center for inspection.

7. Location of the unit

• Place the unit in a well-ventilated location.

Take special care to provide plenty of ventilation on all sides of

the unit especially when it is placed in an audio rack. If

ventilation is blocked, the unit may overheat and malfunction.

• Do not expose the unit to direct sunlight or heating units as the

unit’s internal temperature may rise and shorten the life of the

pickup.

• Avoid damp and dusty places and places directly affected by

vibrations from the speakers. In particular, avoid placing the

unit on or above one of the speakers.

• Be sure the unit is placed in a horizontal position. Never place

it on its side or on a slanted surface as it may malfunction.

• When you place the unit near a TV, radio, or VCR, the playback

picture may become poor and the sound may be distorted. In

this case, place the unit away from the TV, radio, or VCR.

8. Care

From time to time you should wipe the front and rear panels and

the cabinet with a soft cloth. For heavier dirt, dampen a soft cloth

in a weak solution of mild detergent and water, wring it out dry,

and wipe off the dirt. Following this, dry immediately with a

clean cloth.

Do not use rough material, thinners, alcohol or other chemical

solvents or cloths since these could damage the finish or remove

the panel lettering.

9. Notes on Handling

When shipping the unit, use the original shipping carton and

packing materials. For maximum protection, repack the unit as it

was originally packed at the factory.

• Do not use volatile liquids, such as insect spray, near the unit.

Do not leave rubber or plastic products in contact with the unit

for a long time. They will leave marks on the finish.

• The top and rear panels of the unit may become warm after a

long period of use. This is not a malfunction.

• When the unit is not in use, be sure to remove the disc and turn

off the power.

• If you do not use the unit for a long period, the unit may not

function properly in the future. Turn on and use the unit

occasionally.

10.Notes on Moisture Condensation

Moisture condensation damages the unit.

Please read the following carefully.

• What is moisture condensation?

Moisture condensation occurs, for example, when you pour a

cold drink into a glass on a warm day. Drops of water form on the

outside of the glass. In the same way, moisture may condense on

the optical pick-up lens inside the unit, one of the most crucial

internal parts of the unit.

• Moisture condensation occurs in the following cases.

– When you bring the unit directly from a cold place to a

warm place.

– When you use the unit in a room where you just turned on

the heater, or a place where the cold wind from the air

conditioner directly hits the unit.

– In summer, when you use the unit in a hot and humid place

just after you move the unit from an air conditioned room.

– When you use the unit in a humid place.

• Do not use the unit when moisture condensation may

occur.

If you use the unit in such a situation, it may damage discs and

internal parts. Remove the disc, connect the power cord of the

unit to the wall outlet, turn on the unit, and leave it for two or

three hours. After a few hours, the unit will have warmed up and

evaporated any moisture. Keep the unit connected to the wall out-

let and moisture condensation will seldom occur.

DANGER:

VISIBLE LASER AND INVISIBLE RADIATION WHEN

OPEN AND INTERLOCK FAILED OR DEFEATED. DO

NOT STARE INTO BEAM.

CAUTION:

THIS PRODUCT UTILIZES A LASER. USE OF

CONTROLS OR ADJUSTMENTS OR PERFORMANCE

OF PROCEDURES OTHER THAN THOSE SPECIFIED

HEREIN MAY RESULT IN HAZARDOUS RADIATION

EXPOSURE.

This unit contains a semiconductor laser system and is

classified as a “CLASS 1 LASER PRODUCT”. So, to use

this model properly, read this Instruction Manual carefully. In

case of any trouble, please contact the store where you

purchased the unit. To prevent being exposed to the laser

beam, do not try to open the enclosure.

This label on the rear panel states that:

1. This unit is a CLASS 1 LASER PRODUCT and employs

a laser inside the cabinet.

2. To prevent the laser from being exposed, do not remove

the cover. Refer servicing to qualified personnel.

Especificaciones del producto

Marca:	Audio Pro
Categoría:	No categorizado
Modelo:	DVD ONE
Ancho:	244 mm
Profundidad:	210 mm
Adaptador gráfico:	Radeon HD 4200
Tipo de fuente de energía:	ATX
Número de puertos USB 2.0:	4
Puerto(s) VGA (D-Sub):	1
Micrófono, entrada de línea:	Ja
Número de puertos Ethernet LAN (RJ-45):	1
Salidas de auriculares:	1
Puertos DVI-D:	1
Zócalo del procesador:	Socket AM3
Versión de ranuras PCI Express:	2.0
Fabricante del procesador:	AMD
Memoria interna máxima:	16 GB
Adaptador de gráficos incorporado:	Ja
Sistemas operativos compatibles:	Windows 7
Canales de salida de audio:	5.1 kanalen
Guía de Instalación Rápida:	Ja
Tipo de interfaz Ethernet:	Gigabit Ethernet
placa base con chipset:	AMD 785G
Controladores suministrados:	Ja
Ranuras PCI Express x1:	1
Ranuras PCI Express x16:	1
Familia de adaptadores gráficos:	AMD
Canal de memoria:	Dubbelkanaals
Puerto(s) PS/2:	2
Puertos seriales):	1
Componente para:	PC
Tipos de incursión:	0, 1,10
Adaptador de gráficos de memoria máxima:	512 MB
Ranuras PCI:	2
Procesadores compatibles:	AMD Phenom II X6
Máx. número de procesadores SMP:	1
Factor de forma de la placa base:	micro ATX
Número de ranuras de memoria:	2
Velocidades de reloj de memoria admitidas:	800,1066,1333 MHz
tipo de BIOS:	AMI
Tamaño de la memoria del BIOS:	64 Mbit
Soporte para procesamiento paralelo:	Niet ondersteund
Conector de alimentación ATX (24 pines):	Ja
Conexión del ventilador de la fuente de alimentación:	Ja
Conexiones USB 2.0:	3
Conexión para panel de audio en el frente:	Ja
Conexión de intrusión al chasis:	Ja
Salida-S/PDIF:	Ja
Entrada de audio CD/AUX:	Ja
Número de conexiones ATA paralelas:	1
Número de conectores SATA II:	6
Tipo de conexión del controlador:	SB710
Conexiones para fuentes de alimentación EATX:	1