AudioControl TXJTD8 Manual de Usario

AudioControl Altavoz de subgraves TXJTD8

Lee a continuación 📖 el manual en español para AudioControl TXJTD8 (4 páginas) en la categoría Altavoz de subgraves. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/4
Dual 8” Under Seat Subwoofer Enclosure
FOR JEEP GLADIATOR JT
INSTALLATION GUIDE
NOTE! Read this installation guide thoroughly before disassembling or modifying
the vehicle. Installation of this product requires technical skill, experience and
specialized tools. If in doubt, it’s recommended to have it professionally installed
by an authorized or Dealer.Stinger Audio Control
TXJTD8
A video installation guide is available at:
https://stingerelectronics.com/collections/vehicle-specic-subwoofer-enclosures/products/txjtd8
2
INSTALLATION NOTES
INCLUDED HARDWARE
RECOMMENDED TOOLS
M6 FLANGED HEX HEAD BOLT (2)
2 1.0 5mm / in Length ENCLOSURE MOUNTING BRACKETS (2) QUICK-PLUG SPEAKER CONNECTOR (1)
10mm Wrench
Wire Strippers
Optional:
Small Pick / Flat Screwdriver
T25 Torx
Nylon Panel Tool
Wire Crimper
Solder/Solder Gun
The TXJTD8 is designed to mount under the rear seat of the Jeep Gladiator. The factory under seat storage will
need to be removed and two of the factory bolts will be used to mount the enclosure.
For JT models equipped with a factory subwoofer, there is no need to remove the subwoofer, but unplugging
the factory subwoofer is recommended. See Step 6.
Some installation steps are more easily completed with a second person.
Speaker wire is required.
Final enclosure impedance: 2ohms.
Recommended amplier rating: 400-1,000 watts @ 2ohms.
Recommended Subsonic Filter Setting: 31 Hz.
1 2 3
3
INSTALLATION
Step 2
Step 1
With the rear seat bottoms folded up,
remove the four 10mm (Torx #40) bolts
securing the storage wall to the oor.
Remove the storage wall from the vehicle.
On both sides of the speaker enclo-
sure, loosen the 10mm bolts halfway
and remove the mounting brackets
by passing the bolt head through the
“keyhole” on the brackets.
Leave the 10mm bolts partially
installed in the rear of the enclosure.
NOTE: On models equipped with a locking
storage bin, the bottom of the storage bin
has rubber mats that need to be removed
to access the four mounting bolts.

Especificaciones del producto

Marca: AudioControl
Categoría: Altavoz de subgraves
Modelo: TXJTD8

¿Necesitas ayuda?

Si necesitas ayuda con AudioControl TXJTD8 haz una pregunta a continuación y otros usuarios te responderán


Altavoz de subgraves AudioControl Manuales

AudioControl

AudioControl TXJTD8 Manual de Usario

16 Septiembre 2024
AudioControl

AudioControl TXJWB12 Manual de Usario

15 Septiembre 2024

Altavoz de subgraves Manuales

Últimos Altavoz de subgraves Manuales

Canton

Canton SUB 8.2 Manual de Usario

27 Octubre 2024
Deaf Bonce

Deaf Bonce Machete MFX30D2 Manual de Usario

26 Octubre 2024
Phoenix Gold

Phoenix Gold ZP12D4 Manual de Usario

21 Octubre 2024
Phoenix Gold

Phoenix Gold ZP12D2 Manual de Usario

21 Octubre 2024
Phoenix Gold

Phoenix Gold Z12AB Manual de Usario

21 Octubre 2024
Phoenix Gold

Phoenix Gold Z10AB Manual de Usario

21 Octubre 2024
Phoenix Gold

Phoenix Gold ZB8P Manual de Usario

21 Octubre 2024
Bowers And Wilkins

Bowers And Wilkins CT 8SW Manual de Usario

20 Octubre 2024
Pioneer

Pioneer TS-W257D2 Manual de Usario

17 Octubre 2024
Vonyx

Vonyx SWP15 Manual de Usario

17 Octubre 2024