Phoenix Gold ZB8P Manual de Usario

Phoenix Gold Altavoz de subgraves ZB8P

Lee a continuación 📖 el manual en español para Phoenix Gold ZB8P (8 páginas) en la categoría Altavoz de subgraves. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/8

ZB8P

8” Slim Active Bass Enclosure

User Manual

ZB8P - 8” SLIM ACTIVE BASS ENCLOSURE

PANEL CONTROLS AND FEATURES

A. POWER STATUS LED

This bi-coloured LED glows green when power is on

and no problems are detected. If one of the

protection circuits come on, the LED will glow RED.

B. PHASE SHIFT

Use this switch to help compensate for time alignment

problems in the system. Such problems usually result

from having the subwoofer at a dierent distance

from the listener than the other speakers in the

system.

C. AUTO POWER ON

The AUTO POWER ON (ON/OFF) is for high level

(speaker level) connections. When the switch is in the

‘ON’ position, the subwoofer will AUTO POWER ON

when there is a signal input. If the ampliﬁer detected

no signal input, the ampliﬁer will auto turn o. If you

prefer to use the remote turn on/o connection, the

switch is in the OFF position.

(NOTE: Please connect the remote terminal to the

remote output of head unit (See Fig 4) when you hear

the unit turn ON/OFF POP noise from the subwoofer).

D. LOW PASS FILTER

This control allows you to deﬁne the frequency range

you want the subwoofer ampliﬁer to receive. The

subwoofer will reproduce all sound below the

frequency you set.

Note: The low pass ﬁlter frequency can be higher

or lower than the standard. There have +/-20%

tolerance.

E. BASS BOOST

The BASS BOOST feature will increase the sound level

in the bass frequencies.

F. INPUT GAIN CONTROL

After you have installed your system, turn this control

to minimum. Turn the head unit on (and the

subwoofer will turn on via the remote connection).

Turn the head unit volume to about 2/3 full level.

Slowly turn up the subwoofer input gain control until

you hear a small amount of distortion. Then reduce

the level until the distortion is completely gone. Level

the control at this setting.

G. REMOTE LEVEL CONTROL PORT

Attach the included remote level control to control

the volume level of the subwoofer independently.

H. HIGH LEVEL (SPEAKER LEVEL) INPUTS

If your head unit does not have RCA outputs you can

use the speaker outputs for the audio source for the

subwoofer. Use the supplied cable and wire harness

and connect the outputs properly as shown in the

connection diagram in this manual.

I. LOW LEVEL RCA INPUTS

Low level inputs are the recommended way to

introduce the audio signal to the subwoof er if RCA

outputs are present on your head unit or other signal

source (such as a sound processor).

J. FUSE

Do not use a fuse with a dierent value and never

replace the fuse with a wire or coin.

K.POWER INPUT TERMINAL

ZB8P - 8” SLIM ACTIVE BASS ENCLOSURE

WIRING

LOW LEVEL INPUT WIRING

Low-level (RCA) input wiring is preferred for best audio performance. Most trunk and under-seat installations will require

a 6-12 feet RCA cable. Always use a high quality cable.

NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your ampliﬁer at the same time!

FIG 1

HIGH LEVEL INPUT WIRING

The high level input(s) should only be used when your receiver lacks RCA outputs. If the RCA outputs are not present,

connect the speaker outputs from the receiver to the high level input connector of the ampliﬁer. Be sure to observe

polarity to avoid audio phase problems.

NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your ampliﬁer at the same time!

FIG 2

POWER CONNECTIONS

Connect the ground terminal to the closest point on the chassis of the vehicle. Use 8 gauge (or heavier) wire to

connect the ground cable.

Connect the remote terminal to the remote output of head unit using 16 gauge (or heavier) wire.

Connect an empty fuse holder within 16” (40 cm) of the car battery, and run 8 gauge (or heavier) cable from this fuse

to the ampliﬁer location. Then connect the fuse holder to the “BATT+” (+ l 2V) connection on the subwoofer rear panel.

Especificaciones del producto

Marca:	Phoenix Gold
Categoría:	Altavoz de subgraves
Modelo:	ZB8P

¿Necesitas ayuda?

Si necesitas ayuda con Phoenix Gold ZB8P haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

Altavoz de subgraves Phoenix Gold Manuales

Phoenix Gold ZP12D4 Manual de Usario

21 Octubre 2024

Phoenix Gold ZP12D2 Manual de Usario

21 Octubre 2024

Phoenix Gold Z12AB Manual de Usario

21 Octubre 2024

Phoenix Gold Z10AB Manual de Usario

21 Octubre 2024

Phoenix Gold ZB8P Manual de Usario

21 Octubre 2024

Phoenix Gold ZMAX18PB Manual de Usario

15 Septiembre 2024

Phoenix Gold ZMAX82 Manual de Usario

15 Septiembre 2024

Phoenix Gold ZDSB200S Manual de Usario

15 Septiembre 2024

Phoenix Gold Z18AB Manual de Usario

15 Septiembre 2024

Phoenix Gold ZDSB200 Manual de Usario

15 Septiembre 2024

Altavoz de subgraves Manuales

Últimos Altavoz de subgraves Manuales

Canton SUB 8.2 Manual de Usario

27 Octubre 2024

Deaf Bonce Machete MFX30D2 Manual de Usario

26 Octubre 2024

Bowers And Wilkins CT 8SW Manual de Usario

20 Octubre 2024

Pioneer TS-W257D2 Manual de Usario

17 Octubre 2024

Vonyx SWP15 Manual de Usario

17 Octubre 2024

JL Audio SGR-10TW3 Manual de Usario

13 Octubre 2024

Teufel T6 Manual de Usario

13 Octubre 2024

Polk DB1040 Manual de Usario

10 Octubre 2024

Blaupunkt GBW801 Manual de Usario

7 Octubre 2024

JL Audio TW1 Manual de Usario

6 Octubre 2024