Behringer 297 Dual Portamento/CV Utilities Manual de Usario
Behringer
Sintetizador
297 Dual Portamento/CV Utilities
Lee a continuación 📖 el manual en español para Behringer 297 Dual Portamento/CV Utilities (2 páginas) en la categoría Sintetizador. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/2
V 1.0
Quick Start Guide
SYSTEM 100
297 DUAL PORTAMENTO/
CV UTILITIES
Legendary Analog Portamento
Controller and CV Utilities for Eurorack
Controls
(1) MIXER SIG IN – Connect incoming signals via 3.5 mm
TS cables. Inputs 3 and 4 feed +10/-10 V respectively to
the mixer inputs if no jack is inserted, which can be used
to oset the overall mixer output control voltage.
(2) PORTA SIG OUT – Send the portamento signal to another
module via 3.5 mm TS cable.
(3) PORTA SIG IN – Connect a signal to the portamento
section via 3.5 mm TS cable.
(4) SIG LEVEL – Adjust the level of the signals connected to
the mixer inputs.
(5) INV OUT – Send the mix of inputs 1-4 as an
inverted signal.
(6) NON INV OUT – Send the mix of inputs 1-4 as a
non-inverted signal.
(7) TIME – Adjust the portamento time.
(8) CV IN – Connect a voltage to control the portamento time
from another module.
(9) +10/-10 V LEVEL – Adjust the level of the +10 V and
-10 V outputs.
(10) +10/-10 V OUT – Send the +10 V and -10 V signals via
3.5 mm TS cable.
Power Connection
The module comes with the required power cable for connecting
to a standard Eurorack power supply system. Follow these
steps to connect power to the module. It is easier to make
these connections before the module has been mounted into
a rack case.
1. Turn the power supply or rack case power o and
disconnect the power cable.
2. Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector has
a tab that will align with the gap in the socket, so it cannot
be inserted incorrectly. If the power supply does not have
a keyed socket, be sure to orient pin 1 (-12 V) with the red
stripe on the cable.
3. Insert the 10-pin connector into the socket on the back of
the module. The connector has a tab that will align with the
socket for correct orientation.
4. After both ends of the power cable have been securely
attached, you may mount the module in a case and turn on
the power supply.
(1)
(4)
(5)
(6)
(3)(2)
(7)
(8)
(10)
(9)
Installation
The necessary screws are included with the module for mounting
in a Eurorack case. Connect the power cable before mounting.
Depending on the rack case, there may be a series of xed holes
spaced 2 HP apart along the length of the case, or a track that
allows individual threaded plates to slide along the length
of the case. The free-moving threaded plates allow precise
positioning of the module, but each plate should be positioned in
the approximate relation to the mounting holes in your module
before attaching the screws.
Hold the module against the Eurorack rails so that each of the
mounting holes are aligned with a threaded rail or threaded
plate. Attach the screws part way to start, which will allow
small adjustments to the positioning while you get them all
aligned. After the nal position has been established, tighten the
screws down.
Specications
Inputs
Mixer signal input
Type 8 x 3.5 mm TS jacks, DC coupled
Impedance >50 kΩ, unbalanced
Max input level ±10 V
Portamento signal input
Type 2 x 3.5 mm TS jacks, DC coupled
Impedance 95 kΩ, unbalanced
Max input level +10 V
Portamento CV input
Type 2 x 3.5 mm TS jacks, DC coupled
Impedance 2 MΩ, unbalanced
CV input level +10 V
Outputs
Mixer outputs, inverted & non inverted
Type 8 x 3.5 mm TS jacks, DC coupled
Impedance 50 Ω, unbalanced
Max output level ±10 V
Portamento signal output
Type 2 x 3.5 mm TS jacks, DC coupled
Impedance 250 Ω, unbalanced
Max output level +10 V
+10 V output
Type 3.5 mm TS jack, DC coupled
Impedance 1 kΩ, unbalanced
Max output level +10 V
-10 V output
Type 3.5 mm TS jack, DC coupled
Impedance 1 kΩ, unbalanced
Max output level -10 V
Controls
Mixer input level -∞ to unity gain
Portamento 10 ms to 3 s time
+10 V output 0 V to +10 Vvoltage control
-10 V outpu 0 V to -10 Vt voltage control
Power
Power Eurorack supply
Current 70 mA (+12 V), 60 mA (-12 V) draw
Physical
Dimensions 38 x 81 x 129 mm
(1.5 x 3.2 x 5.1")
Rack units 16 HP
Weight 0.18 kg (0.4 lbs)
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suered by any
person who relies either wholly or in part upon any description, photograph,
or statement contained herein. Technical specications, appearances and
other information are subject to change without notice. All trademarks are the
property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake,
Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone
and Coolaudio are trademarks or registered trademarks of Music Tribe
Global Brands Ltd. © Music Tribe Global Brands Ltd. 2020 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information
regarding Music Tribe’s Limited Warranty, please see complete details online
at musictribe.com/warranty.
Especificaciones del producto
| Marca: | Behringer |
| Categoría: | Sintetizador |
| Modelo: | 297 Dual Portamento/CV Utilities |
¿Necesitas ayuda?
Si necesitas ayuda con Behringer 297 Dual Portamento/CV Utilities haz una pregunta a continuación y otros usuarios te responderán
Sintetizador Behringer Manuales
2 Octubre 2024
2 Octubre 2024
2 Octubre 2024
30 Septiembre 2024
30 Septiembre 2024
23 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
15 Septiembre 2024
Sintetizador Manuales
- Sintetizador Casio
- Sintetizador Yamaha
- Sintetizador Suzuki
- Sintetizador Roland
- Sintetizador Korg
- Sintetizador Boss
- Sintetizador Cre8audio
- Sintetizador Make Noise
- Sintetizador Moog
- Sintetizador Fred's Lab
- Sintetizador Soma
- Sintetizador Novation
- Sintetizador Vermona
- Sintetizador Modal Electronics
- Sintetizador Synamodec
- Sintetizador Waldorf
- Sintetizador (Recovery)
- Sintetizador Future Retro
- Sintetizador ELTA Music
- Sintetizador LennarDigital
Últimos Sintetizador Manuales
26 Octubre 2024
22 Octubre 2024
20 Octubre 2024
19 Octubre 2024
12 Octubre 2024
12 Octubre 2024
5 Octubre 2024
2 Octubre 2024
1 Octubre 2024
23 Septiembre 2024