Blebox wlightbox Manual de Usario

Blebox Casa inteligente wlightbox

Lee a continuación 📖 el manual en español para Blebox wlightbox (3 páginas) en la categoría Casa inteligente. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/3
SAFETY RULES
Connect only in accordance with the diagram presented in the
manual. Improper connections may be dangerous, it can damage
the controller, and loss of the warranty.
Do not connect loads with more than permissible power.
DANGER! Risk of electric shock! Even with the device turned o,
the outputs may be live. All assembly work should be ALWAYS
performed with the disconnected power circuit.
Connecting the device to a power supply that does not meet the
quality requirements specied in EN 50081-1, EN 50082-1, UL508,
EN 60950 will invalidate the warranty.
Disconnect the installation supply voltage before installing the controller.
Remember that any mounting works should be carried out when the mains
voltage is disconnected (switch o the mains fuse or disconnect the power
cord from the mains socket).
1INSTALLATION
CONNECTION DIAGRAMS
FIRST LED RGBW CONTROLLER BASED ON THE µWiFi TECHNOLOGY
LED controller
with μWiFi tecnology
wLightBox + 4-channel strip
12 - 24V max 12A, 3 A channel
R G B W
_
++
µWiFi LED RGBW controller wlightBox
LED STRIP
RGB+W max12A
R
G
B
W
110 / 230V
12-24V
+
power
supply
wLightBox + LED RGB strip + 1-color LED strip (white color)
LED STRIP
WHITE max 3A
12 - 24V max 12A, 3 A channel
R G B W
_
++
µWiFi LED RGBW controller wlightBox
LED STRIP
RGB+W max 9A
R
G
B
W
110 / 230V
12-24V
+
power
supply
wLightBox + 4 single-channel LED strip
12 - 24V max 12A, 3 A channel
R G B W
_
++
µWiFi LED RGBW controller wlightBox
LED STRIP max 3A
-
LED STRIP max 3A
-
LED STRIP max 3A
-
LED STRIP max 3A
-
110 / 230V
12-24V
+
power
supply
Download the . If you have an Android mobile device, free wBox application
you will nd the application in the Play Store. For iOS devices the application
is in the App Store.
By using your mobile phone or tablet, connect it to the device wireless
network. To do this, enter to your smartphone or tablet settings, then go to
setting of the WiFi network and nd the network name "wLightBox-
-xxxxxxxxxx” where xxxxxxxxxx is the serial number of the device. Connect to
this network.
Turn on the wBox application. A device will appear at the top of the screen. To
add it to the application, click on "+" on the right side of the name. To pre-con-
gure the controller, click on the default device name.
2FIRST START
Go to settings ("Settings" icon in the upper right corner of the screen) and
select the correct option in the "Device type" eld depending on the LED strip
connected. You can choose between the options "RGBW" - for three-color
strips with additional white, "RGB" - for three-color strips and "MONO" - for
monochromatic strips or halogen bulbs. After saving the settings, go to the
main panel by clicking the arrow in the upper left corner. Test the controller
works- if you have a multi-colored tape, select color from the color selection
circle and set the brightness using the scrollbar. If you have monochrome
strip, select the brightness of the channel with the scrollbar. Test the
controller's work by moving the brightness scrollbar several times in the
extremes and intermediate positions - the light source should change its
brightness. The control panel also has an additional eects menu – the access
to it is achieved by moving-up the screen from the bottom ("More" at the
bottom of the screen). In the menu you can choose predened colors and set
the duration of the color, or choose a predened lighting eect and set the
transition times.
TECHNICAL SPECIFICATIONS
12 - 24V
< 1W
4
open drain, PWM,
low side control
39 x 35 x 20 mm
24V
288W
You can also set the conguration using the web browser
of your phone / tablet. After connecting to the wireless
network of the controller, turn on the browser and go
website www.blebox.eu
3ACCESS POINT AND WIFI NETWORK SETTINGS
Once you turn on the controller for the rst time, you can proceed to its
further conguration. Being connected to the WiFi network emitted by the
device, in the control panel of the wBox application select the device, then go
to “Settings” (icon at the top-right corner of the screen).
You can change the name of the device that is displayed in the wBox
application. In addition, you can change the name and password of its
generated WiFi network. Remember that changing the network name or
password will disconnect the device immediately after you click the "Save"
button, so re-connect to the device using the newly assigned network name
and password.
You can add the controller to your home WiFi network to control it through
this home network or from anywhere in the World. To do this, in the "Connect"
settings section, select a network name from the list and press "Connect". If is
required, enter the WiFi network password. During the connection of the
controller to your home network, the phone / tablet may disconnected from
the network. In this case, you will need to reconnect your phone / tablet to the
controller network.
Please remember that in order to control the device outside the local WiFi
network, from anyplace in the World by using the wBox application, the
option "Remote access enabled" in the controller settings must be set to "Yes".
Once you've nished conguring the WiFi network, you can disconnect your
phone/tablet from the controller network and connect your mobile device
directly to your home WiFi network. The control from the wBox application
will work the same way as when the phone / tablet is connected to the
controller network. If the user leaves the local network, for example, leaving
home or using the mobile data, the wBox application will signal this state as
"Remote mode". In this case, the devices can be controlled, but for security
reasons settings are not available.
The controller should be installed in a place protected against adverse
environmental conditions, protected from third party access - in the ush box
or inside the enclosure of the controlled device. It is recommended that the
device be mounted in a stable and xed position.
Familiarize yourself with the diagram and then proceed with the installation
of the controller. Pay special attention to the designation of the controller
connectors. Start by connecting the power wires: (+) (red or black with a white
dotted line) and (-) (black).
Connect the LED strip paying attention to the polarity. Depending on the use,
it is possible to connect a single RGBW strip, one RGB strip, an RGB strip with
a white strip or four monochromatic strips. The "+" cathode wire (usually
white color in multicolored strips or red in monochrome strips) must be
connected to the "+" connector of the controller, and the anode wire "-" (color
corresponding to each color of the LEDs in multi-color strips or white color
in monochrome strips) to the corresponding output, i.e. R, G, B or W. The
controller also allows to control halogen lamps, the polarity of the wiring is
not important.
After making sure that the device is connected in accordance with the
diagram and that there are no metal components near the controller which
may accidentally cause short-circuit, start the device by turning on the power
(turning on the mains fuse or connecting the power cord to the power outlet).
RGB / RGBW / MONO
supply voltage
energy consumption
number of outputs
type of outputs
maximum voltage
maximum load
color mode
dimensions
maximum current 12A (3A /channel)
for more information
visit our website
www.blebox.eu
or send us an email to: info@blebox.eu
support is available at
support@blebox.eu
ADDITIONAL INFORMATION
SOFTWARE UPDATE
To update the software in the controller, connect it to your home WiFi network
(see "Access Point and WiFi Network Settings" section) which is connected to
the Internet. Go to “Settings” (icon at the top-right corner of the screen) and
click the "Get new rmware" button in the nal section on settings. Wait about
1 minute, do not close the interface and don’t perform other actions. The
device will download the latest software. The software version number,
hardware version and device identier can be read at the bottom of the
settings screen.
made of polyurethane composition
not containing halogens, self-
extinguishing for thermal
class B (130 °C)
direct connection (as Access Point), Wi-Fi
connection via a standard router,
connection with access from any
location in the world (requires only
access to the Internet)
μWiFi, compatible with WiFi, 802.11g
bidirectional, encrypted
communication standard
transmission type
mode
radio frequency
API
compatible devices
IP20
2.4 GHz
open
Apple iPhone, Apple iPad, iPad Mini,
Android, computers and mobile
devices supporting HTML5
in the ush-mounted box, on the lamp
housing, directly connected
to the LED strip, e.g. furniture
inverted polarization, ESD
housing
protection level
mounting method
protection
LOCATION AND TIME OF THE DEVICE,
SCHEDULE
The controller has the ability to work according to a given schedule. To make
this possible, set the device's time. Go to settings in the "Device time" section,
click "Change timezone". Then select your region and location from the list,
conrm your selection clicking the "Save" button. The device will synchronize
its time with the server time (if the controller is in a WiFi network with access
to Internet) or it will download time from the phone / tablet. It is recommen-
ded that the controller is always connected to a WiFi network with Internet
access so that it can automatically synchronize its clock.
To be able to control devices using the local sunrise and sunset, you must also
select the location of the controller. You can specify the location of the device
using a smartphone or tablet. In the section "Device location", click "Set
locations". Browser will ask whether to share locations - allow. In the "Coordi-
nates" eld,should appear the approximate coordinates of your location. If the
"Set locations" button blinks red with the word "Error", or the "Coordinates"
eld did not change the value from "Not set" to numeric data, a failurehas
occurred during the location download. You should make sure that the phone
/ tablet has a GPS module and that the sharinglocation service is enabled on
the phone.
Adding schedule entries can be performed by clicking the "Add item" button
in the "Schedule" section of settings. You can select the days in which the task
will be performed, the type of entry (at a specic time, or relative to sunrise /
sunset - only having a correctly set location) and set the parameters of the
task. The set tasks will be visible as a list, individual entries can be edited or
deleted.

Especificaciones del producto

Marca: Blebox
Categoría: Casa inteligente
Modelo: wlightbox

¿Necesitas ayuda?

Si necesitas ayuda con Blebox wlightbox haz una pregunta a continuación y otros usuarios te responderán


Casa inteligente Blebox Manuales

Blebox

Blebox SwitchBox Manual de Usario

11 Septiembre 2024
Blebox

Blebox switchBoxD Manual de Usario

11 Septiembre 2024
Blebox

Blebox wLightBoxS Manual de Usario

11 Septiembre 2024
Blebox

Blebox wlightbox Manual de Usario

11 Septiembre 2024
Blebox

Blebox dimmerBox Manual de Usario

11 Septiembre 2024
Blebox

Blebox LightBox Manual de Usario

11 Septiembre 2024

Casa inteligente Manuales

Últimos Casa inteligente Manuales

Brilliant

Brilliant Nexus Home Ultimate 21465 Manual de Usario

27 Octubre 2024
D-Link

D-Link DCS-8010 Manual de Usario

20 Octubre 2024
Niko

Niko 350-20071 Manual de Usario

18 Octubre 2024
Qnect

Qnect QN-WP01 - 414000005 Manual de Usario

16 Octubre 2024
Qnect

Qnect QN-WP04 - 414000001 Manual de Usario

16 Octubre 2024
Elro

Elro AB600S-2 Manual de Usario

13 Octubre 2024
Tenda

Tenda SP15 Manual de Usario

9 Octubre 2024
Eufy

Eufy Lumi Plug-in Night Light Manual de Usario

6 Octubre 2024
ETiger

ETiger ES-D4A Manual de Usario

3 Octubre 2024
Netgear

Netgear Orbi RBS50Y Manual de Usario

2 Octubre 2024