Boss MPWT50RGB Manual de Usario

Boss No categorizado MPWT50RGB

Lee a continuación 📖 el manual en español para Boss MPWT50RGB (6 páginas) en la categoría No categorizado. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/6
MPWT50RGB
5.25” (133 mm )
Poly injection cone
1” (25 mm) PEI dome tweeter
Rubber surround
Built-in
4 Ohms
Max 500 Watts
140Hz - 20kHz
92dB (1 watt/1 meter)
6.38” x 9” x 6.19”
(162 x 229 x 157 mm)
8.16 lbs (3.7 kg)
t le D c or (2) Sp pod wieaker h ma LE onnect
r m t(4) 130x14x2mm ubber oun ing strip
(4) 120x14x1mm er rubb m toun ing strip
(2) 48x30x2mm er rubb m toun ing pad
) (4
M6x60mm scre w
m t(4) 2" oun ing a m m alu inu b nd for a2" nd ll ion.1.875" insta at
1. m t(4) 75" oun ing lu inua m m ba for 1. a 1.nd 75" nd 5" sta at in ll ion.
t (4) M6 locknu
fl h(4) M6 at was er
5.25” (133 mm) 2-Way Marine/
Powersports Roll Cage/
Waketower Speaker Pods
Congratulations on your
purchase of a product.
It has been engineered to bring you
the highest level of performance.
Its quality will afford you years of
listening pleasure.
Thank you for making
your choice for audio
entertainment!
Specifications
Mid Bass Driver:
Tweeter:
Impedance:
Frequency Response:
Power Handling:
Crossover network:
Sensitivity:
Gross Weight (in gift box):
Dimensions (W x H x D):
Introduction
What is included?
Safety considerations when installing
Your new MPWT50RGB waketower speakers are high-power,
fully-waterproof 2-way systems featuring 5.25” drivers and
a 1” PEI dome tweeter.
understands that wake tower speakers are used in many
different types of installations. Our versatile mounting solutions give
you the ability to attach our wake tower speakers to mounting tubes
with diameters of 1.5” - 2” (38 - 51mm).
Before you begin installation, please check that your product contains
the following contents:
Please remember that these are heavy products that will be installed in a
boating environment. T hese vehicles can travel high at speeds and be uns ablet .
So please consider this and use extreme caution.
Some safety considerations include:
1- Do not mount the speakers in a location where someone may either walk
into or strike their head. During a turbulent ride, please make sure that you do
not loosen footing and fall or hit the unit, or it may cause injury.
2- Secure the wires to the speakers in multiple locations along their route to
your audio source, so that there are no hanging loops of wire. Having unsecure
wires in any hanging conditions can cause entanglement and injury.
3- Tighten the aluminum bands with rubber inserts using care. Do not over
compress the rubber inserts. After installation is complete, please recheck all
bolts and tighten them further if needed before taking your boat or vessel out
for an audio adventure.
4- Do not install these speakers where they may block the view of the pilot and
prevent safe operation of the vessel or vehicle.
A cificat o ll spe ion ares subject t
c t tice.hange wi hou not
) (1
LED pow wier re
) (1
LE onn h D c ection wi wire t female c oronnect
) (1
Rem te tro con ol
) (1
Keyc tahain g
STEP3
STEP2
MPWT50RGB
STEP1
STEP4
5.25” (133 mm) 2-Way Marine/Powersports
Roll Cage/Waketower Speaker Pods
Installation instructions
It is strongly recommended that you work with an assistant to install these speakers.
To adjust the mounting angle, loosen the metal
base of the mounting band by unbolting the two
screws.
Make sure to put all components of the mounting
hardware in a safe location.
Metal base
48 x 30mm rubber pad
Aluminum band
Rubber strip
Mounting cage bar
(part of your marine
boat or powersports
vehicle)
Metal base
Twist the metal base to determine the
optimal mounting angle for the speaker on the
cage bar. Then secure the metal base
by tightening the two screws.
Place a supplied rubber (48 x 30 mm) pad on the
metal base of the mounting band to t preven
abrasion and secure lampin c g.
P cela two upplied rubber s st rip arounds the cage bar
to prevent abra ion and secures clamping.
T shhen pu t swo upplied aluminum bands er he ov t
c age bar and, align he aluminum band t s wi heth t
me al bat se on the speakers.

Especificaciones del producto

Marca: Boss
Categoría: No categorizado
Modelo: MPWT50RGB

¿Necesitas ayuda?

Si necesitas ayuda con Boss MPWT50RGB haz una pregunta a continuación y otros usuarios te responderán




No categorizado Boss Manuales

No categorizado Manuales

Últimos No categorizado Manuales