Boss MR692B Manual de Usario

Boss Vocero MR692B

Lee a continuación 📖 el manual en español para Boss MR692B (2 páginas) en la categoría Vocero. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/2
MR692B/MR692W
Installation Instructions
6” x 9” (152 x 229 mm) Marine
2-Way Full Range Speakers (1 Pair)
- 1 -
Thank you for purchasing a BOSS Audio Systems product. Please read through these
instructions carefully so you will know how to install this product properly.
Package contents
2x Speakers (with xed grill)
8x Mounting screws and clip nuts
2x EVA gaskets
Cutout template and warranty
Specications
2-way speaker, full range
Woofer: 6” x 9” (152 x 229 mm),
polypropylene cone, resin treated cloth surround
Tweeter: 1” (25 mm), dome
Output power: max 350 W
Nominal impedance: 4 Ω
Frequency response: 60 Hz-20 kHz
System sensitivity: 92 dB (1 watt/1 meter)
Outdoor use. Water resistant, but never
submerge.
Speaker dimensions
A
B
B
A
C
E
D
A. Overall diameter: 7.75” x 10.5” (197 x 267 mm)
B. Mounting hole diameter: 6.02” x 8.78” (153 x 223 mm)
C. Mounting depth: 3.38” (86 mm)
D. Grill protrusion: 1.375” (35 mm)
E. Outer motor diameter: 4.80” (122 mm)
- 2 -
Installation
Important notes
Consult an expert when in doubt about installation. Professional installation is always recommended.
Prior to installation, disconnect the negative terminal of the vehicle battery.
When installing the speakers, take into consideration the risks that can arise from devices being torn away
in the case of an accident. Therefore, make sure the speakers are rmly secured and the mounting area is
sufciently stable.
If you must modify the vehicle for the speaker installation, make sure you do not impair the safety and structural
integrity of the vehicle.
Before you drill or cut any holes, investigate your vehicle’s layout very carefully. Take special care when you
work near the fuel tank, fuel lines, hydraulic lines and electrical wiring.
Mounting
If you replace your vehicle’s existing speakers, simply use the existing mounting locations. Or create a cutout in
your vehicle panel for speaker installation.
1. Determine the location (e.g. side panels or dash panel) where the speakers are to be mounted.
2. Cut a mounting hole and screw holes on the mounting surface as follows:
Verify the supplied template matches the speaker and mounting cut-out.
Cut out the template along the cut line. Use the cut-out template to mark the mounting hole and screw holes
on the mounting surface. Then cut the holes for the speaker to be mounted.
3. Complete the speaker wiring connection.
4. Fasten the speaker into the mounting hole with four supplied screws and clip nuts.
Make sure the speaker sits ush across the entire mounting surface.
Make sure to properly break in speakers and not reach max volume until after two 20 minute cycles at regular
volume.
Wiring
Using high quality marine-grade speaker wires with spade connectors (not included), connect the speakers to
your 12VDC source unit (to audio outputs on the amplier or speaker wires of the head unit).
The positive wire is connected to the terminal marked ” and the negative wire to the terminal marked ”. Make + -
sure the wires are rmly attached to the terminals.
Amplifier
(12V)
Speaker wires
Speaker wires
Left Right
Make sure the speakers are wired correctly at 4 ohms. Observe speaker polarity when making connections.
Avoid routing wires near any sharp or moving parts. Run wires away from other wires that may cause unwanted
noise. Insulate bare wires properly.
0722

Especificaciones del producto

Marca: Boss
Categoría: Vocero
Modelo: MR692B

¿Necesitas ayuda?

Si necesitas ayuda con Boss MR692B haz una pregunta a continuación y otros usuarios te responderán




Vocero Boss Manuales

Vocero Manuales

Últimos Vocero Manuales