Broan 114 Manual de Usario

Broan Calentador 114

Lee a continuación 📖 el manual en español para Broan 114 (12 páginas) en la categoría Calentador. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/12
Page 1
MODEL 114
KICKSPACE HEATER
Factory Wired 240/208 V.A.C.
READ AND SAVE THESE INSTRUCTIONS
VOLTS WATTS AMPS BTU/HR
240 1500 6.3 5120
208 1125 5.4 3840
120* 1500 12.5 5120
120* 750 6.3 2560
PLANNING
This heater is designed for installation in an enclosed space such
as under a counter or kickspace to provide warm, gentle heat at
the floor level. Reread Safety Notes 3 through 8 for guidelines in
planning the installation.
The Model 114 is factory wired for 240/208 V.A.C. operation. It offers
a choice of heat outputs and can be internally connected for multiple
wattages at different voltages shown in the table below.
All ratings are 1‑Phase, 60 Hertz.
*See “FIELD CONVERSION TO 120 V.A.C.” section.
IMPORTANT INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE
INSTALLING OR USING THIS HEATER.
To reduce the risk of fire, electric shock, or injury to persons,
observe the following:
1. Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer at the address
or telephone number listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by a
qualified person(s) in accordance with all applicable codes
and standards, including fire‑rated construction codes and
standards.
4. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
5. This heater is hot when in use. To avoid burns, do not let bare
skin touch hot surfaces. Keep combustible materials, such as
furniture, pillows, bedding, papers, clothes, etc. and curtains at
least 3 feet (0.9 m) from the front of the heater.
6. Extreme caution is necessary when any heater is used by
or near children or invalids and whenever the heater is left
operating and unattended.
7. Do not operate any heater after it malfunctions. Disconnect
power at service panel and have heater inspected by a
reputable electrician before reusing.
8. Do not use outdoors.
9. To disconnect heater, turn controls to off, and turn off power
to heater circuit at main disconnect panel (or operate internal
disconnect switch, if provided).
10. Do not insert or allow foreign objects to enter any ventilation or
exhaust opening, as this may cause an electric shock or fire, or
damage the heater.
11. To prevent a possible fire, do not block air intakes or exhaust in
any manner.
12. A heater has hot and arcing or sparking parts inside. Do not
use it in areas where gasoline, paint, or flammable vapors or
liquids are used or stored.
13. Use this heater only as described in this manual. Any other use
not recommended by the manufacturer may cause fire, electric
shock, or injury to persons.
14. To avoid electrical shock: Do not install unit in a tub or shower
enclosure or any location where it may come in contact with
water. Never place a switch where it can be reached from a tub
or shower.
15. Do not connect heater to dimmer switch or speed control.
16. Do not install heater upside down or sideways. Heater must be
located in the horizontal position.
17. Do not recess louvered face of the heater more than three inches
from the vertical face of any overhang (cabinet).
18. Provide this heater with a separate electrical circuit following
directions under “Wiring” section.
19. This product is equipped with a thermostat which may start it
automatically. Turn off power at service entrance before cleaning
or servicing.
20. This heater includes a visual alarm to warn that parts are getting
excessively hot. If the alarm lights are activated, immediately
turn the heater off and inspect for any objects on or adjacent
to the heater that may cause high temperatures.
21. This product must be grounded.
SAVE THESE INSTRUCTIONS
Cutout dimension: 18‑3/8” x 3‑5/8”
Page 2
MODEL 114
INSTALLATION
WARNING: To reduce the risk of fire, do not store or use gaso-
line or other flammable vapors and liquids in the vicinity of
the heater.
CAUTION: High temperature, risk of fire, keep electrical cords,
drapery, furnishings, and other combustibles at least 3 feet (0.9
m) from the front of the heater and away from the side and rear.
1. Mark the intended mounting location in the base plate under the
counter or kickspace, and remove required material to provide
for easy insertion and removal of the heater cabinet.
2. The unit will be secured in place with screws through the side
angle support brackets. Provide adequate material behind side
angle support for secure mounting.
FIELD CONVERSION TO 120 V.A.C.
If a 120 V.A.C. circuit is to be used, make wiring changes as follows:
1. Disconnect white wire from heater element terminal “2” and
connect it to terminal “4.” The heater will now operate at 120
V.A.C., 750W, 6.3A.
2. For 120 V.A.C, 1500W, 12.5A operation, add the short jumper red
wire (provided) between terminals “1” and “2”.
3. Remove alarm light wire leads from terminals “1” and “3” of
the high temperature limit. Remove white wire lead from limit
terminal “1” and reconnect at limit terminal “3”. Secure wire leads
with wire tie so there is no interference with unit operation.
NOTE: Terminal numbers are marked on the side of the blower
housing, above the heater elements.
THERMOSTAT INSTALLATION
NOTE: The thermostat control circuit must be wired prior to the
wiring of the heater unit.
This heater may be thermostatically controlled by either a line volt‑
age wall‑mounted thermostat (Model 86W), or an optional built‑in
thermostat accessory kit (Model 90). Model 90 thermostat kits are
designed for easy installation with this heater. Instructions for in‑
stalling thermostats are provided below and are also supplied with
each thermostat kit.
OPTIONAL LINE VOLTAGE WALL-MOUNT THERMOSTAT
1. Locate thermostat on an inside wall away from all drafts and
approximately 4‑5 feet above the floor.
2. Route all wiring through the thermostat first and then to the
heater.
OPTIONAL (MODEL 90) UNIT-MOUNT THERMOSTAT
1. Remove the top cover from the heater.
2. Remove the 5/8” knockout located on the left side of the front
panel (use a screwdriver to remove the knockout). Also remove
the two plastic hole plugs (see illustration).
SIDE ANGLE
SUPPORT BRACKETS
Page 3
MODEL 114
3. Install thermostat from back side of front panel and fasten in
place, from front, with two screws and washers provided (see
illustrations).
4. Attach temperature control knob by gently pushing it on to the
thermostat shaft. Flats on shaft and knob must line up for proper
installation (do not force control knob onto shaft).
5. Remove black wire from thermal fuse and attach it to thermostat
terminal marked “4”.
6. Remove white wire from temperature limit terminal marked “1”
(Note: the other end of this wire is attached to incoming field
wiring) and attach it to the thermostat terminal marked “1”.
7. Attach black thermostat wire to thermal fuse and therwhite ‑
mostat wire to the temperature limited marked “3”.
WIRING
Installation work and electrical wiring must be done by a qualified
person(s) in accordance with all applicable codes and standards,
including fire-rated construction codes and standards.
1. Run electrical power cable to installation location. Provide two
feet of slack to allow heater to be pulled out far enough to remove
top cover for cleaning or servicing.
NOTE: It is recommended that flexible conduit be used for field wir‑
ing to the unit to protect the wires from sharp objects or hazardous
environments.
NOTE: Be sure supply voltage meets the equipment requirement.
Refer to the rating plate, unit wiring diagram and specification table.
2. Remove top cover for access to wiring box at rear of heater.
3. Remove one
of the two
knockouts and
connect power
cable to heater
using appropri‑
ate connector.
Allow at least
six inches of
wiring inside of
wiring box.
4. Connect black
to black, white to
white and green
(or bare wire) to
ground screw,
as shown. Tuck
wires down
inside the wiring box.
5. Replace top cover.
WARNING: Do not operate heater without top cover in place.
6. Slide heater into place and secure to mounting surface.

Especificaciones del producto

Marca: Broan
Categoría: Calentador
Modelo: 114

¿Necesitas ayuda?

Si necesitas ayuda con Broan 114 haz una pregunta a continuación y otros usuarios te responderán


Calentador Broan Manuales

Broan

Broan 9815WH Manual de Usario

17 Septiembre 2024
Broan

Broan 174F Manual de Usario

14 Septiembre 2024
Broan

Broan 124 Manual de Usario

14 Septiembre 2024
Broan

Broan 114 Manual de Usario

14 Septiembre 2024
Broan

Broan 198 Manual de Usario

14 Septiembre 2024
Broan

Broan 112 Manual de Usario

14 Septiembre 2024
Broan

Broan 174 Manual de Usario

14 Septiembre 2024
Broan

Broan 174FT Manual de Usario

14 Septiembre 2024
Broan

Broan 170 Manual de Usario

14 Septiembre 2024
Broan

Broan 170FT Manual de Usario

14 Septiembre 2024

Calentador Manuales

Últimos Calentador Manuales

Vonroc

Vonroc PH503AC Manual de Usario

27 Octubre 2024
JANDY

JANDY VersaFlo Manual de Usario

27 Octubre 2024
Master

Master 215TMHD-KFA Manual de Usario

25 Octubre 2024
Yamazen

Yamazen DBC-VK123 Manual de Usario

23 Octubre 2024
Yamazen

Yamazen DCT-B08 Manual de Usario

23 Octubre 2024
Yamazen

Yamazen DOL-J122 Manual de Usario

23 Octubre 2024
Yamazen

Yamazen DSF-S122 Manual de Usario

23 Octubre 2024
Yamazen

Yamazen DBC-SK123 Manual de Usario

23 Octubre 2024
Yamazen

Yamazen DBC-W121 Manual de Usario

23 Octubre 2024
Yamazen

Yamazen DMF-D021 Manual de Usario

23 Octubre 2024