BSS Audio Soundweb London MC-1 Manual de Usario

BSS Audio No categorizado Soundweb London MC-1

Lee a continuación 📖 el manual en español para BSS Audio Soundweb London MC-1 (9 páginas) en la categoría No categorizado. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/9
User’s Guide
BSS Audio MC-1
Stand-Alone Media Converter
Gigabit Ethernet
Copper to Fiber
1000Base-T to 1000Base-SX/LX
BSS MC-1 Gigabit Ethernet mediaAudio
converter connects 1000Base-T
shielded or unshielded twisted-pair copper
cable to 1000Base-SX or 1000Base-LX, fiber-
optic cable. is a stand-MC-1
alone media converter
Installation . . . . . . . . . . . . . . . . . .3
Operation . . . . . . . . . . . . . . . . . . .7
Cable Specifications . . . . . . . . . . .9
Technical Specifications . . . . . . .11
Troubleshooting . . . . . . . . . . . . .12
Contact Us . . . . . . . . . . . . . . . . .13
Compliance Information . . . . . . .15
MC-1 RJ-45 1000Base-T
100 m (328 ft)*
SC, 1000Base-LX, 1310 nm single mode
10 km *(6.2 miles)
*Typical maximum cable distance. Actual
distance is dependent upon the physical
characteristics of the network installation.
2BSS Audio 800-931-2357 8760 South Sandy Parkway, Sandy, Utah 84070 www.bssaudio.com 800-931-2357 3
Installation
Set the 6-position switch
The 6-position switch is located
on the side of the media
converter.
Use a small flat blade
screwdriver to set the
recessed switches.
All switches are shown in
the default position, UP.
Note: Switch positions S2 and S3 work together to configure the media
converter for Pause conditions.
S1 Remote-Fault Detection
up Disabled
down Enable
S2 & S3 work in combination
Pause
10 sw position 2 up and 3 down: Symmetric
01 sw position 2 down and 3 up: Asymmetric
11 sw positions 2 and 3 up: Pause is OFF (default position)
00 sw positions 2 and 3 down: Symmetric and Asymmetric
S4 Transparent Link Pass-Through
up Enable Link Pass-Through
down Disable Link Pass-Through
S5 Fiber Auto-Negotiation
up Disable Fiber Auto-Negotiation for the fiber link
(default setting)
down Enable Fiber Auto-Negotiation for the fiber link
S6 Loop Back
up Disable RX/TX signal loop back (default setting)
down Enable RX/TX signal loop back
2. Pause (symmetric)
3. Pause (asymmetric)
4. Transparent Link Pass-Through
5. Auto-Negotiation
1. Remote Fiber Fault Detect
6. Loop Back
4
Installation -- Continued
Install Mode
During installation, set converter DIP switch 4 DOWN; leave all other switches
in the UP position . This disables Transparent Link Pass-Through and(default)
Auto-Negotiation, allowing individual copper and fiber links to be established
(both copper port LEDs will turn ON with each device-to-device connection)
independent of a complete end-to-end connection.
Operation Mode
After installation is complete (all copper and fiber ports connected and linked),
set all switches to the UP position .(default))
Fiber Auto-Negotiation
Fiber Auto-Negotiation allows the fiber interface to detect and then advertise the
supported features of the remote device; this occurs only when a fiber cable is
connected to a device with a negotiating port. The process is as follows:
1. The fiber interface detects the supported features of the remote partner.
2. These abilities are passed to the twisted-pair interface and advertised.
3. Once the twisted-pair interface has a link at the highest common
capability, it passes the result to the fiber interface.
4. The fiber interfaces then start advertising these capabilities. At this point,
the link between the fiber and the negotiating port is complete.
If the MC-1 is connected via fiber to another MC-1, both media converters
must have the Fiber Auto-Negotiation setting disabled (switch5 UP).
Note: Transparent Link Pass-Through cannot be(switch position 4 enabled)
turned OFF ( when Fiber Auto-Negotiation is ON disabled) (enabled).
5
Installation -- continued
Install the fiber cable
1. Locate a 1000Base-SX/LX compliant fiber cable with male, two-stranded
TX to RX connectors installed at both ends.
2. Connect the fiber cables to the MC-1 media converter as
described:
Connect the male TX cable connector to the female TX port.
Connect the male RX cable connector to the female RX port.
3. Connect the fiber cables to the other device (another media converter,
hub, etc.) as described:
Connect the male TX cable connector to the female RX port.
Connect the male RX cable connector to the female TX port.
RX
TX TX
RX
Device Device
BSS Audio 800-931-2357 8760 South Sandy Parkway, Sandy, Utah 84070 800-931-2357 www.bssaudio.com

Especificaciones del producto

Marca: BSS Audio
Categoría: No categorizado
Modelo: Soundweb London MC-1

¿Necesitas ayuda?

Si necesitas ayuda con BSS Audio Soundweb London MC-1 haz una pregunta a continuación y otros usuarios te responderán




No categorizado BSS Audio Manuales

No categorizado Manuales

Últimos No categorizado Manuales