Buffalo TeraStation 4400D Manual de Usario
Lee a continuación 📖 el manual en español para Buffalo TeraStation 4400D (4 páginas) en la categoría Server. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/4
The TS4000 series will not work without disks. Please prepare 1 or more un-partitioned
HDDs for the setup process. Use either new HDD(s) or delete all partitions (and
therefore all data) with a partition editor before you start with existing HDD(s).
Step by step
1. Mount one or more HDDs to a frame and insert it in the TeraStation™.
2. Prepare the MicroSD and the USB adapter and insert the USB
adapter into a USB 2.0 port, connect power and network.
3. Move the boot switch to USB position.
4. Boot the TeraStation™.
Now the unit gives after some minutes a tone, the display
goes red and it says “push function button to start”.
5. Push the function button until beep sounds.
The display status color will be blue and sequence through these messages:
Recovery Preparing
System Recovering
FW/Updating
Recovery Finished, “Change Boot SW”
Setup Guide
TeraStation™ 4000
www.buffalo-technology.com
Setup Guide
TeraStation™ 4000
www.buffalo-technology.com
6. The TeraStation™ will shut down and the Power button will no
longer be lit green. The display and Info light stay on.
7. Remove the USB adapter, move the switch on the
back to HDD, press the power button
If you use just one drive you will have a brief warning for missing
HDDs and afterwards the TeraStation™ will operate normally.
If you use more than one drive: The first HDD is mounted and will work normally
and the other HDDs are mounted but not yet formatted. The display will therefore
turn red and the status LEDs of all unformatted drives will show red as well.
The warning, red display, and red LEDs will remain until you finish formatting all HDDs.
8. Now please install the NAS Navigator on your computer and click
‘Refresh’ to reveal your new TeraStation™ 4000. Right click on it and select
‘Settings’. A browser window will launch the admin interface. It’s also
possible to access the admin interface by entering the TS4000 series IP
address (shown on the TS’s display) directly into a browser window.
Setup Guide
TeraStation™ 4000
www.buffalo-technology.com
9. Format all unformatted HDDs via the admin interface. Once formatting
is completed the status in the admin page will change to ‘Formatted’
please wait to see this before continuing, depending on HDD
capacity this could take approximately 8 minutes per drive.
Especificaciones del producto
Marca: | Buffalo |
Categoría: | Server |
Modelo: | TeraStation 4400D |
¿Necesitas ayuda?
Si necesitas ayuda con Buffalo TeraStation 4400D haz una pregunta a continuación y otros usuarios te responderán
Server Buffalo Manuales
22 Agosto 2024
5 Agosto 2024
28 Julio 2024
22 Julio 2024
22 Julio 2024
20 Julio 2024
Server Manuales
- Server Sony
- Server HP
- Server Medion
- Server Acer
- Server Apc
- Server Hikvision
- Server Asus
- Server SilverStone
- Server Lenovo
- Server Black Box
- Server Axis
- Server Gigabyte
- Server Cisco
- Server AVerMedia
- Server Matrox
- Server Fujitsu
- Server Linksys
- Server Supermicro
- Server GeoVision
- Server Netgear
- Server QNAP
- Server LaCie
- Server Dell
- Server Asustor
- Server ZyXEL
- Server Western Digital
- Server Intel
- Server Fantec
- Server D-Link
- Server Seagate
- Server Iomega
- Server Synology
- Server Blackmagic Design
- Server ATen
- Server Ibm
- Server Provision ISR
- Server StarTech.com
- Server Advantech
- Server Avocent
- Server Lindy
- Server AMX
- Server Atlantis Land
- Server Mobotix
Últimos Server Manuales
17 Septiembre 2024
16 Septiembre 2024
16 Septiembre 2024
16 Septiembre 2024
13 Septiembre 2024
12 Septiembre 2024
12 Septiembre 2024
11 Septiembre 2024
10 Septiembre 2024
10 Septiembre 2024