Camille Bauer Sineax V610 Manual de Usario

Camille Bauer No categorizado Sineax V610

Lee a continuación 📖 el manual en español para Camille Bauer Sineax V610 (4 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/4
Fig. 1
Transmitter (1)
1 Operating Instructions (2) each in German, French and
English
Open and short-circuit sensor circuit supervision
Signalling mode: Output signal at open and short-circuit
sensor circuit on 21.6 mA
V 610 Be 151 952-01 08.05
2. Scope of supply (Figs. 1 and 2)
Contents
1. Read first and then … .......................................................1
2. Scope of supply .................................................................1
3. Brief description .................................................................1
4. Technical data ....................................................................1
5. Mounting ............................................................................2
6. Electrical connections ........................................................2
7. Commissioning ..................................................................3
8. Maintenance .......................................................................3
9. Releasing the transmitter ...................................................3
10. Dimensional drawings ........................................................4
11. Declaration of conformity ...................................................4
3. Brief description
The is a two-wire transmitter. SINEAX V 610
It is used for measuring temperature in conjunction with a
resistance thermometer. Thermocouple non-linearities are au-
tomatically compensated. The output signal is a current in the
range 4 … 20 mA.
The sensor circuit is monitored for open and short-circuits and
the output responds in a defined manner if one is detected.
The power supply of 12…30 V DC is connected together with
the signal by the two leads connected to the measurement
output (loop powered).
(1)
4. Technical data
Measuring input
Input variable and measuring range
Input variables Measuring ranges Order No.
Temperatures with
resistance thermometers
for wire connectionthree-
Pt 100, IEC 60 751
0 … 100 °C 154 823
0 … 150 °C 154 831
0 … 200 °C 154 849
– 30 … + 70 ºC 154 857
– 50 … + 150 °C 154 865
Measuring output (output/powering circuit)
Output signal IA: Impressed DC current,
linear with temperature
Standard range: 4…20 mA, 2-wire technique
External resistance R ext max. =Power supply [V] – 12 V
(load): [k ] Max. output current [mA]Ω
900
12 24
36
0
600
Load max. [ ] withΩ
20 mA output
Power supply [V]
30
10
Subject to change without notice
Temperature
Transmitter
SINEAX V610
The following symbols in the Operating Instructions indicate safety
precautions which must be strictly observed:
Camille Bauer LTD
Aargauerstrasse 7
CH-5610 Wohlen/Switzerland
Phone +41 56 618 21 11
Fax +41 56 618 35 35
e-mail: info@camillebauer.com
http://www.camillebauer.com
Operating Instructions
The instruments must only be disposed of in the
correct way!
1. Read first and then …
The proper and safe operation of the device as-
sumes that the Operating Instructions are read
and the safety warnings given in the various
Sections
5. Mounting
6. Electrical connections
7. Commissioning
are .observed
The device should only be handled by appropriately trained
personnel who are familiar with it and authorised to work in
electrical installations.
Unauthorized repair or alteration of the unit invalidates the
warranty!
Fig. 2
6. Electrical connections
The leads are connected to the screw terminals for max. 0 to
4mm2 (single wire) and 0 to 2.5 mm2 (fine wire) on the front of
the transmitter. The applicable enclosure Protection Class for
the terminals is IP 20 according to EN 60 529.
Also note that, ...
... the data required to carry out the prescribed
measurement must correspond to those marked
on the nameplate (Fig. 7) of SINEAX V 610.
... the total loop resistance connected to the
output (receiver plus leads) ex-doesnot
ceed the m aximu m permissib l e value
Rext. , see in Section “Measuring output”
“4. Technical data”!
… the measurement input and output cables should
be twisted pairs and run as far as possible away
from heavy current cables!
In all other respects, observe all local regulations
when selecting the type of electrical cable and
installing them!
When deciding where to install the transmitter
(measuring location), take care that the limits
of the operating temperature are kept:
– 25 and + 55 °C
Fig. 3. Mounting onto top-hat rails 35 15 or 35 7.5 mm.× ×
Simply clip the device onto the top-hat rail (EN 50 022) (see
Fig. 3).
Fig. 4. Mounting onto rail «G».
Power supply
DC voltage: Supply 12 … 30 V DC
max. residual ripple 1% p.p.
(supply must not fall below 12 V)
Protected against wrong polarity
Accuracy data
Reference value: Measuring span
Basic accuracy: Error limits ± 0.2% at reference con-≤
ditions
Linearity: 0.1%≤
Reference conditions
Ambient temperature: 23 °C
Power supply: 18 V DC
Output burden: 250 Ω
Additional errors (additive)
Low measuring ranges:
Resistance
thermometer ± 0.3 K at measuring spans < 400 °C
Standards
Electromagnetic
compatibility: The standards EN 50 081-2 and
EN 50 082-2 are observed
Protection acc. to
IEC 529 resp.
EN 60 529: Housing IP 40
Terminals IP 20
Electrical standards: Acc. to IEC 1010 resp. EN 61 010
Environmental conditions
Operating temperature: –25 to +55 ºC
Storage temperature: –40 to +80 ºC
Humidity relative: 75%, no moisture condensation≤
Altitude: 2000 m max.
Indoor use statement
Simply clip the device onto the rail «G» EN 50 035-G32 (see
Fig. 4).
5. Mounting
The SINEAX V 610 can be mounted on a top-hat rail or on a
rail «G».
Notes:
Pay attention to correct connection according to nameplate on
transmitter!
It is not necessary to compensate the leads, providing the three
leads have identical resistances. The lead resistance must not
be greater than 30 per lead.Ω
6.2 Measuring output leads (output/powering circuit)
Connect the measuring output leads (analogue output and power
supply) to terminals + and – acc. to Fig. 6.
Permissible power supply H
12 … 30 V DC
Permissible load max. Rext
(acc. to power supply)
900 at 30 VΩ
600 at 24 VΩ
400 at 20 V Ω
Fig. 6. Measuring output.
Rext
A
B
C
D
ϑ
D
C
B
A
RTD
Three-wire
connection
Fig. 5. Measuring input.
Note that twisted leads must be used for the output signal.
Fig. 7. Example of a nameplate.
7. Commissioning
Switch on the measuring input and the power
supply. The ambient temperature must be
between .– 25 and + 55 °C
8. Maintenance
No maintenance is required.
9. Releasing the transmitter
Fig. 8
Fig. 9
Release the transmitter from a rail “G“ as shown in Fig. 9.
Release the transmitter from a top-hat rail as shown in Fig. 8.
6.1 Alternative measurement connections
Connect the measuring leads (Fig. 5).

Especificaciones del producto

Marca: Camille Bauer
Categoría: No categorizado
Modelo: Sineax V610

¿Necesitas ayuda?

Si necesitas ayuda con Camille Bauer Sineax V610 haz una pregunta a continuación y otros usuarios te responderán


No categorizado Camille Bauer Manuales

Camille Bauer

Camille Bauer Sineax V624 Manual de Usario

11 Septiembre 2024
Camille Bauer

Camille Bauer Sineax I552 Manual de Usario

11 Septiembre 2024
Camille Bauer

Camille Bauer Sineax M561 Manual de Usario

11 Septiembre 2024
Camille Bauer

Camille Bauer Sineax TI802 Manual de Usario

11 Septiembre 2024
Camille Bauer

Camille Bauer Sineax I542 Manual de Usario

11 Septiembre 2024
Camille Bauer

Camille Bauer Sineax VS30 Manual de Usario

11 Septiembre 2024
Camille Bauer

Camille Bauer Sineax TI801 Manual de Usario

11 Septiembre 2024
Camille Bauer

Camille Bauer Sineax U543 Manual de Usario

11 Septiembre 2024
Camille Bauer

Camille Bauer Sineax V610 Manual de Usario

11 Septiembre 2024
Camille Bauer

Camille Bauer Sineax I538 Manual de Usario

11 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024