Chamberlain 050DCRJWFMC Manual de Usario

Chamberlain receptor 050DCRJWFMC

Lee a continuación 📖 el manual en español para Chamberlain 050DCRJWFMC (12 páginas) en la categoría receptor. Esta guía fue útil para 12 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/12

Logic Board

Model 050DCRJWFMC

WARNING: This product can expose you to chemicals

including lead, which are known to the State of California to

cause cancer or birth defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov.

To prevent possible SERIOUS INJURY or DEATH:

• Disconnect ALL electric and battery power BEFORE performing ANY

service or maintenance.

To prevent damage to the receiver/logic board, DO NOT touch printed

circuit board of replacement receiver/logic board during installation.

ALWAYS wear protective gloves and eye protection when changing the

battery or working around the battery compartment.

NOTICE: This device complies with Part 15 of the FCC rules and Industry Canada’s license-

exempt RSSs. Operation is subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Any changes or modiﬁcations not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device must be installed to ensure a minimum 20 cm (8 in.) distance is maintained between

users/bystanders and device.

This device has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC rules and Industry Canada ICES standard. These limits are

designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Before you begin. Your new MyQ® serial number is located on the

replacement label with your replacement logic board. You will need this new MyQ

serial number to connect your opener to the network.

Disconnect power.1. 2. Open the front panel . (A)

Remove the battery cover. 3.

Disconnect the battery. Remove

the battery and set aside .(B)

Add the Step Saver sticker under 4. the yellow program button.

Add the Step Saver sticker under 5.

the yellow program button.

Disconnect the wires coming from

the safety reversing sensors,door

control, door lock and cable

tension monitor from the logic

board (C).

Remove the receiver logic board 6. cover .(D)

Disconnect all the wiring harnesses 7.

from the logic board .(E)

Remove the four screws securing 8. the logic board. Rmove the logic

board , and discard.(F)

Install the new logic board and 9.

connect the wiring harnesses.

Route the antenna through the

channel in the cover.

10. Adhere the new MyQ serial

number label over the original

label on the logic board cover.

11. Reprogram the travel and test the

safety reversal system (see pages

and 3).

12. Program all remote controls and

keyless entries (see page 4)..

13. Use the MyQ app to add the

new MyQ serial number to your

account.

Adjustment

Program the Travel

1. Press and hold the Adjustment Button until the UP Button begins to

ﬂash and/or a beep is heard. The Safety Reversing Sensors will be

disconnected during the Program the Travel process.

2. Press and hold the UP Button until the door is in the desired UP

position.

3. Once the door is in the desired UP position, press and release the

Adjustment Button.The garage door opener lights will flash twice and

the DOWN Button will begin to flash.

4. Press and hold the DOWN Button, until the door is in the desired

DOWN position.

5. Once the door is in the desired DOWN position, press and release the

Adjustment Button. The garage door opener lights will flash twice.

Program the Travel is now complete. If the garage door opener lights

flash 5 times, then programming has timed out and the Travel Limits

have not been set. Please restart the Program the Travel process.

6. To prevent damage to vehicles, be sure fully open door provides

adequate clearance.

Automatic Force Setup

Once both the up and down positions have been manually set, the Safety

Reversing Sensors will reconnect and become operational. Then, the opener

will enter a force-sensing operation by automatically moving the door open

and close. The garage door opener will sound an audible and visual alert

before automatically opening and closing the door. The garage door opener

will beep three times, confirming that the Automatic Force Setup completed

successfully. Adjustment is complete.

If you hear one long beep after the door attempts to move, then the

Automatic Force Set Up has not completed successfully. Please start over at

step 1 of Program the Travel.

Without a properly installed safety reversal system, persons

(particularly small children) could be SERIOUSLY INJURED or KILLED

by a closing garage door.

• Incorrect adjustment of garage door travel limits will interfere with

proper operation of safety reversal system.

• After ANY adjustments are made, the safety reversal system MUST

be tested. Door MUST reverse on contact with 1-1/2" high (3.8 cm)

object (or 2x4 laid flat) on floor.

To prevent damage to vehicles, be sure fully open door provides

adequate clearance.

1. 2.

3. 4.

Adjustment

Button

UP Button

DOWN Button

Safety Reversing Sensor Safety Reversing Sensor

1-1/2" (3.8 cm) board

(or a 2x4 laid flat)

Adjustment

Test the Safety Reversal System

1. With the door fully open, place a 1-1/2” (3.8 cm) board (or a 2x4 laid

flat) on the floor, centered under the garage door.

2. ress the remote control push button to close the door. The door

MUST reverse when it makes contact with the board.

If the door stops but does not reverse:

1. Review the installation instructions provided to insure all steps were

followed;

2. Repeat Program the Travel (see Adjustment Step 1);

3. Repeat the Safety Reversal test. If the test continues to fail, call a

trained door systems technician.

Test the Protector System®

1. Press the remote control push button to open the door.

2. Place the opener carton in the path of the door.

3. Press the remote control push button to close the door. The door will

not move more than 1”.

The garage door opener will not close from a remote if the indicator light in

either sensor is off(alerting you to the fact that the sensor is misalignedor

obstructed).

Test Cable Tension Monitor

With the door fully closed, push on the front of the cable tension monitor. A

click should be heard. If there is no click, the roller may be hitting the jamb

and not allowing the switch to detect slack in the cable. Make sure the cable

tension monitor is mounted flush with the wall and the roller is free from

any obstructions.

If your cable tension monitor has been activated the UP and DOWN arrows

will flash diagnostic code 3-5.will activate the garage door opener.

Test the Automatic Garage Door Lock

1. With the garage door fully closed, the automatic garage door lock bolt

should be protruding through the track.

2. Open the garage door. The automatic garage door lock should retract

before the garage door begins to move.

3. Close the garage door. When the garage door reaches the fully closed

position, the automatic garage door lock should automatically activate

to secure the door.

Disengage the automatic garage door lock by sliding the manual release to

the open position.

To Open the Door Manually

Disengage any door locks before proceeding. The door should be fully

closed if possible. Pull down on the emergency release handle until a click

is heard from the garage door opener and lift the door manually.

To reconnect the door to the garage door opener, pull the emergency

release handle straight down a second time until a click is heard from the

garage door opener. The door will reconnect on the next UP or DOWN

operation.

Without a properly installed safety reversal system, persons

(particularly small children) could be SERIOUSLY INJURED or KILLED

by a closing garage door.

• Safety reversal system MUST be tested every month.

• After ANY adjustments are made, the safety reversal system MUST

be tested. Door MUST reverse on contact with 1-1/2" (3.8 cm) high

object (or 2x4 laid flat) on the floor.

Without a properly installed safety reversing sensor, persons

(particularly small children) could be SERIOUSLY INJURED or KILLED

by a closing garage door.

Locked Position

Manual Release

Emergency

Release Handle

Especificaciones del producto

Marca:	Chamberlain
Categoría:	receptor
Modelo:	050DCRJWFMC
Tipo de operación:	Knoppen
Color del producto:	Meerkleurig
Pantalla incorporada:	Ja
Peso.:	1400 g
Ancho:	260 mm
Profundidad:	170 mm
Altura:	130 mm
Peso del embalaje:	1700 g
Ancho del embalaje:	295 mm
Empaquetadura en profundidad:	206 mm
Altura del embalaje:	155 mm
Manual de usuario:	Ja
Fuente-de-alimentación:	AC/Batterij
Tipo de embalaje:	Doos
Interruptor encendido / apagado:	Ja
Formato de audio soportado:	MP3
Puerto USB:	Ja
País de origen:	China
Batería/Voltaje de la batería:	1.5 V
Número de puertos USB 2.0:	1
Energía promedio:	3 W
Número de altavoces incorporados:	2
Número soportado de baterías/baterías:	6
Control del volumen:	Knoppen
Asa de transporte:	Ja
tipo de sintonizador:	Digitaal
Número:	1
Modos de reproducción:	Next, Previous, Repeat all, Repeat one
Tipo de unidad óptica:	Speler
Auriculares apagados:	Nee
Botones de control:	Play/pause, Stop
Entrada de línea:	Ja
Reproducir MP3:	Ja
Entrada auxiliar:	Ja
Tipo-de-unidad-óptica:	CD, CD-R, CD-RW
Bandas de frecuencia soportadas:	FM, MW
Número de canales preestablecidos:	30
Mecanismo de carga:	Bovenkant
Platina de casete:	Nee
Tamaño de batería compatible:	C
Compatibilidad con acoplamiento de Apple:	Niet ondersteund
Reproducción directa USB:	Ja
banda FM:	87.5 - 108 MHz
sintetizador PLL:	Ja
Altura del paquete principal (exterior):	356 mm
Ancho del embalaje principal (exterior):	315 mm
Peso bruto del embalaje principal (exterior):	7200 g
Longitud del paquete principal (exterior):	435 mm
Cantidad por caja principal (exterior):	4 stuk(s)
voltaje-de-entrada-de-CA:	230 V
Frecuencia-de-entrada-de-CA:	50 Hz
Consumo de energía (típico):	14 W
Baterias-incluidas:	Nee
Tecnología de batería:	Alkaline
Tipo-de-visualización:	LCD
Rango de banda MW:	522 - 1620 kHz