Comar AST-200 Manual de Usario

Comar No categorizado AST-200

Lee a continuación 📖 el manual en español para Comar AST-200 (6 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/6
AST200 V1.0
AST-200
AIS Transponder Antenna Splitter
Installation & User Manual
2
Before operating the unit you should familiarize yourself with the
complete user manual supplied with the product.
Electrical safety
Make sure the power supply is switched off before you make any
electrical connections to the unit.
Product installation
This equipment must be installed in accordance with the
instructions provided in this manual. Failure to do so could result in
poor performance, personal injury and/or damage to your vessel
and/or connected equipment.
Cables
The supplied cables should only be cut, shortened or lengthened by
an appropriate supplier.
General
The compass safe distance of this unit is 0.5m or greater for 0.3°
deviation.
In accordance with a policy of continual development and product
improvement the AST-200 hardware and software may be
upgraded from time to time and future versions of the AST-200 may
therefore not correspond exactly with this manual.
When necessary, upgrades to the product will be accompanied by
updates or addenda to this manual. Information contained in this
manual is liable to change without notice.
Comar Systems Ltd. disclaims any liability for consequences
arising from omissions or inaccuracies in this manual and any other
documentation provided with this product.
© 2010 Comar Systems Ltd.
L
L
L
LL
a
a
a
aa
L
L
L
LL
L
L
L
LL
L
L
L
LL
www.busse-yachtshop.de | info@busse-yachtshop.de
3
1. Introduction
Congratulations on the purchase of your AIS Transponder Antenna Splitter.
It is recommended that your antenna splitter is installed by a professional
installer.
The AST-200 allows your existing VHF antenna to be used by both a VHF
radiotelephone and an AIS Transponder.
The AST-200 also includes an antenna connection for FM broadcast
receivers providing a third use for your existing VHF antenna.
This manual describes the installation and operation of the AST-200.
4
2. Installation
2.1 Before you start
The following items are supplied in the AST-200 packaging:
• The AST 200 unit itself.
• This operating manual.
You will need the following items and tools to complete the installation:
• Class B AIS Transponder.
• Pre-installed VHF Antenna and cable.
• Access to 12V DC or 24V DC power supply where the unit is to be
installed, via a 1A rated fuse or circuit breaker.
• Connector block or junction box for power connections.
• Four M4 (no.6) screws or other fixings appropriate to the mounting
location.
www.busse-yachtshop.de | info@busse-yachtshop.de
5
2.2 Installing the unit
Before starting installation select a suitable location for the antenna splitter.
The unit is intended for installation below deck in a dry location. When
locating the unit you should consider:
• Routing of power and antenna cables to the unit.
• Provision of sufficient space behind the unit for cable connections.
• Maintaining the compass safe distance of 0.5m.
• Visibility of the front panel indicators.
Installation diagram
6
Installation step 1
• Secure the antenna splitter to a flat surface in the selected location.
Use four 5mm wood screws or other fixings suited to the material
the unit is being fixed to.
• The unit may be installed in any orientation.
Installation step 2
Make the electrical connections to the antenna splitter as follows:
• Remove the VHF antenna cable connection from your VHF Radio
and connect it to the connector labelled ‘Antenna’.
• Connect the 1m cable marked “VHF Radio” to your VHF
Radiotelephone antenna connection.
• Connect the 1m cable marked “AIS” to your AIS Transponder
antenna connection..
• Optionally connect the antenna input of an FM Broadcast receiver
to the connector labelled ‘AM/FM’.
• Connect 12VDC or 24VDC power supply to the power cable.
o The red wire should be connected to the positive power
supply connection via a 1A rated fuse or circuit breaker.
o The black wire should be connected to the negative power
supply connection.
Installation step 3
Apply power and verify the unit is operating:
• Apply power to the antenna splitter, AIS Transponder and VHF
radiotelephone.
www.busse-yachtshop.de | info@busse-yachtshop.de

Especificaciones del producto

Marca: Comar
Categoría: No categorizado
Modelo: AST-200

¿Necesitas ayuda?

Si necesitas ayuda con Comar AST-200 haz una pregunta a continuación y otros usuarios te responderán


No categorizado Comar Manuales

Comar

Comar AIS-2-USB Manual de Usario

13 Septiembre 2024
Comar

Comar AIS-2-NMEA Manual de Usario

13 Septiembre 2024
Comar

Comar CSB200 Manual de Usario

13 Septiembre 2024
Comar

Comar ASR 100 Manual de Usario

13 Septiembre 2024
Comar

Comar CSA-300 Manual de Usario

13 Septiembre 2024
Comar

Comar AST-200 Manual de Usario

13 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024