Ei Electronics MCP401RC Manual de Usario

Ei Electronics Cambiar MCP401RC

Lee a continuación 📖 el manual en español para Ei Electronics MCP401RC (2 páginas) en la categoría Cambiar. Esta guía fue útil para 12 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

MCP401RC Manual Call Point

Disconnect the AC mains power supply from the circuit that is to

be used to power the smoke/heat alarms and the MCP401RC.

Install the Smoke/Heat/CO Alarms as per the Installer

Instructions supplied with the alarms.

Select a suitable location where the MCP401RC can be easily

accessed. The unit should not be exposed to dripping or splashing.

Route the wiring (Live, Neutral, Interconnect/Control and Earth)

to the MCP401RC siting location. A minimum 0.75mm

2cable

should be used.

With the 25mm screws provided, fix the mounting box to the wall.

Secure the wall plate to the mounting box using the 35mm

machine screws provided.

SURFACE MOUNTING BOX

SECURITY SCREW

1.5 x 10mm

SCREW (2)

3.5 x 35mm

WALL PLATE

FRONT COVER

OPERATING ELEMENT

SCREW (2)

3.5 x 25mm

Figure 1

Installation & Wiring

6Figure 2

To additional Ei Alarms

if required

(compatible alarms

listed above)

Figure 3

When the black spot on the front face of the MCP401RC is pressed, an alarm signal will be sent along the

interconnect line and all interconnected alarms will sound. The MCP401RC switch element can be reset using

the plastic key supplied.

PLEASE NOTE: The MCP401RC is designed for use with the following models of Smoke/Heat/CO Alarms

- Ei161RC, 164RC, 166RC, 141, 144, 146, 151TL, 154TL, 156TLH, 261ENRC, 261DENRC.

WARNING: This Manual Call Point should be installed by a qualified electrician in accordance with the

Requirements for Electrical Installations published by the Institute of Electrical Engineers (BS7671 current edition).

A maximum of 4 MCP401RC units can be installed on one system in addition to 12 interconnect alarms.

B16073-R0-MCP401RC-UC-ENG 19/4/07 9:17 AM Page 1

P/N B16073 Rev 0

Testing

It is recommended that the MCP401RC is tested directly after installation and then at least monthly.

Test that the MCP401RC call point triggers the alarm(s) by pressing the black spot on the front cover. A

striped warning indicator should drop down into view on the front face (visible through the clear plastic

window). Check that each alarm in the system is sounding.

Reset the MCP401RC by following the instructions in the Resetting section below. The alarms should stop

sounding.

Now turn off the mains power to the system. Repeat the test above (this checks the rechargeable back-up

in the unit). Reinstate the mains power to the system. The MCP401RC will operate in standby with mains

off for over 6 months. With the Manual Call Point triggered it can give an alarm signal for over 16 hours.

The crossed out wheelie bin symbol that is on your

product indicates that this product should not be disposed

of via the normal household waste stream. Proper

disposal will prevent possible harm to the environment or

to human health. When disposing of this product please

separate it from other waste streams to ensure that it can

be recycled in an environmentally sound manner. For

more details on collection and proper disposal, please

contact your local government ofce or the retailer where

you purchased this product.

Aico Ltd. Mile End Business Park,

Maesbury Rd, Oswestry,

Shropshire, SY10 8NN, U.K.

Tel: 0870 7584000 www.aico.co.uk

Ei Electronics. Shannon, Ireland.

Tel: +353 (0)61 471277 www.eielectronics.com

Connect the wiring as shown in Figures 2 & 3 previously. Note: the Earth connection is for convenient

termination of the earth conductor and is not required for the safety of the unit. The wiring should be

installed securely (e.g. tie wrap together) to prevent a hazard if one becomes detached.

Carefully slide the front cover and circuit board diagonally into the mounting box, top section first (see Figure 4).

Then carefully locate the top of the front cover onto the top of the wall plate and hinge down to snap

securely in place (see Figure 5).

Fit the security screw to the call point - the hole for this is on the bottom face of the front cover (see

Figure 6). This is essential for electrical safety as mains is present within the unit.

Reconnect the AC mains power to the circuit and check that the green mains indicator lights on the

Smoke/Heat/CO Alarms are on.

Figure 4 Figure 5 Figure 6

To reset the unit, insert the

reset key into the hole in the

bottom of the front cover. The

striped warning indicator

should disappear. With the key

still inserted, twist it anti-

clockwise until the operating

element clicks back into place,

then remove the reset key (see

Figure 7).

Figure 7 Figure 8

To detach the front cover,

remove the security screw and

insert the reset key into the

bottom of the cover. With the

key firmly inserted, hinge the

bottom of the cover away from

the wall plate/ mounting box

(the reverse motion to fitting).

See Figure 8.

Resetting Opening Unit / Removal

B16073-R0-MCP401RC-UC-ENG 19/4/07 9:17 AM Page 2

Especificaciones del producto

Marca:	Ei Electronics
Categoría:	Cambiar
Modelo:	MCP401RC
Color del producto:	Grijs
Pantalla incorporada:	Nee
Peso.:	4900 g
Ancho:	411.4 mm
Profundidad:	267.5 mm
Altura:	118.4 mm
Nivel de ruido:	36 dB
Manual de usuario:	Ja
Fuente-de-alimentación:	AC
Colocación:	Desktop
Relación de aspecto original:	4:3
red LAN:	Ja
Modos de vídeo compatibles:	768p
Lector de tarjetas de memoria integrado:	Nee
Relación de contraste típica:	5000:1
Capacidad de zoom:	Ja
Incluye adaptador de CA:	Ja
Posicionamiento en el mercado:	Bedrijf
Brillo del proyector:	5200 ANSI lumens
Tecnología de proyección:	DLP
Resolución nativa del proyector:	XGA (1024x768)
Corrección Keystone, vertical:	-30 - 30 °
Corrección Keystone, horizontal:	-30 - 30 °
Adecuado para tamaños de pantalla:	30 - 300 "
Objetivo de distancia de proyección:	- m
Número de colores:	1.073 biljoen kleuren
Rango de frecuencia horizontal:	15 - 102 kHz
Rango de frecuencia vertical:	23 - 120 Hz
Número de puertos USB 2.0:	1
Puerto(s) VGA (D-Sub):	1
Número de puertos HDMI:	2
Tipo de conexión en serie:	RS-232
Micrófono, entrada de línea:	Ja
Audio-ingan (L, R):	1
Entrada de audio para PC:	Ja
Entrada de vídeo compuesto:	1
Entrada de S-Video:	1
Puerto DVI:	Nee
Número de puertos Ethernet LAN (RJ-45):	1
Televisión inteligente:	Nee
Enfocar:	Handmatig
tipo de zoom:	Handmatig
Rango focal:	- mm
Vida útil de la fuente de luz.:	2000 uur
Tipo de fuente de luz:	Lamp
Opción de montaje de bloqueo de cable:	Ja
Tipo de ranura para candado de cable:	Kensington
Altavoces incorporados:	Ja
Energía promedio:	20 W
Número de altavoces incorporados:	2
Consumo de energía (en espera):	0.5 W
Consumo de energía (máx.):	594 W
Relaciones de aspecto admitidas:	4:3
Relación de zoom:	1.6:1
Relación de lanzamiento:	1.41 - 2.25‎
Compensar:	107.5 procent
Formato de señal analógica:	NTSC, PAL, SECAM
Full HD:	Nee
Conexión para adaptador de red:	Ja
Consumo (Modo Económico):	400 W
Potencia de la lámpara:	370 W
Resoluciones de gráficos compatibles:	1024 x 768 (XGA)
Visualización en pantalla (OSD) -talen:	ARA, BUL, CHI (SIMPL), CHI (TR), CRO, CZE, DAN, DEU, DUT, ENG, ESP, FIN, FRE, GRE, HUN, INC, IND, ITA, JPN, KOR, NOR, POL, POR, RUM, RUS, SWE, THA, TUR
Cantidad por paquete:	1 stuk(s)
Visualización en pantalla (OSD):	Ja
Vida útil de la fuente de luz (modo de ahorro):	2500 uur
Nivel de ruido (modo económico):	33 dB
Rango de movimiento vertical de la lente:	0 - 7.5 procent
Número de puertos mini-USB 2.0:	1
Mando a distancia incluido:	Ja
voltaje-de-entrada-de-CA:	100 - 240 V
Frecuencia-de-entrada-de-CA:	50/60 Hz
Consumo de energía (típico):	500 W
Tipo-producto:	Projector met normale projectieafstand