EK Water Blocks 3831109869130 Manual de Usario

EK Water Blocks Refrigeración de hardware 3831109869130

Lee a continuación 📖 el manual en español para EK Water Blocks 3831109869130 (2 páginas) en la categoría Refrigeración de hardware. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

All disclosures, noces and warranty condions are being wrien on the EKWB website. Please read terms of use. Released on 13 th of May. Revision 1.0

Installation manual for -FC750 GTX water block EK

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at for updates. Before www.ekwb.com

installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual before through before beginning with the installation process!

2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).

3. The EK High Flow and EK-PSC type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber O-ring gaskets.

4. The use of corrosion inhibiting coolants is always recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION. Sample picture of GeForce750 GTX series graphics card.

STEP 2: PREPARING YOUR GRAPHIC CARD.

1. REMOVING STOCK COOLER: Remove encircled screw on the

bracket (required only on certain models):

STEP 2 cont.: PREPARING YOUR GRAPHIC CARD

1 cont.. REMOVING STOCK COOLER. Remove all encircled screws. All heat sink assembly screws must

be removed. There are 4 screws on the back of the graphics card. All self-adhesive washers on the front

side of the circuit board must be removed.

2. CLEANING THE PCB. Carefully detach the original stock cooler

after removing screws securing it to the board. Wipe off the all

remains (by using non abrasive cloth or –

qtip

, as shown on sample

photo) of the original thermal compound until the components and

circuit board are completely clean. EKWB recommends the use of

denatured alcohol for removing TIM leftovers.

3. APPLYING THERMAL COMPOUND. Wipe off the

remains (by using non abrasive cloth or –

q-tip

) of the original

thermal compound until the components and circuit board

are completely clean. Apply thermal compound: lightly coat

AMD

GPU chip with enclosed EK-TIM Ectotherm thermal

grease. EKWB recommends to apply thermal grease in cross

form for best rformance (see sample picture). pe

4. CUTTING THERMAL PADS. Your block comes with thermal pads, some of which are already pre-cut.

Others have to be cut to smaller chunks in order to cover all the VRM components such as MOSFETs and

drivers. PLEASE REMOVE THE PROTECTIVE

FOIL FROM BOTH SIDES OF THE THERMAL

PADS PRIOR TO INSTALLATION.

Replacement thermal pads:

Thermal Pad D 0.5mm (RAM 16x) –

STEP 3: INSTALLING THE WATER BLOCK

1. PLACING THERMAL PADS ON PCB. Place thermal pads on chips so that numbers on chips match size of thermal pads. EKWB made sure users have more than

enough pads to cover all surfaces that need to be covered to make block fully functional).

1: Thermal pad D –0.5mm

(for memory IC):

All disclosures, noces and warranty condions are being wrien on the EKWB website. Please read terms of use. Released on 13 th of May. Revision 1.0

2. PLACING THE BLOCK TO THE GRAPHICS CARD. Carefully position the water

block with preinstalled 2.1 mm standoffs on to the graphics card. During this process

please make sure you align mounting holes on the PCB with holes on the water block.

Also pay attention not to use too much force by pressing block down to PCB. Chip dies

are prone to cracking.

3. ATTACHING BLOCK TO THE GRAPHIC CARD. Use a Philips screwdriver screw

in enclosed M2.5 p2-x4 DIN 7985 screws. EKWB recommends users to start tightening

the screws around the GPU core and continue outwards.

STEP 4: CHECKING FOR CONTACTS

If necessary temporarily r

emove the water block to check for uniform surface contact between the block and the components, pay special attention to the VRM section of the

graphics card. Check whether the water block makes contact with the intended integrated circuit. Then repeat sub-steps in previous section to re-attach the block. In case

you fail to obtain good contact, please check again your thermal pad thickness or contact our support service at http://www.ekwb.com/support.

STEP 5: INSTALLATION OF FITTINGS AND TUBING

Screw in the two G1/4 threaded male fittings. Attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit. EKWB recommends using EK-CSQ

fittings with the EK-FC750 GTX series water blocks. To ensure that the tubes are securely attached to the barb/fittings, please use hose clamps or an appropriate

substitute.

You can use any opening as an inlet/outlet port.

CAUTION: In case of using connectors other than EK-CSQ or EK-PSC series compression fittings, take special attention to the length of the fittings’ male G1/4” thread. In

case the thread is longer than 5 mm please use the enclosed 1.8 mm nickel plated spacer!

5mm is the maximum allowed G1/4” thread length!

STEP 6: INSERTING THE CARD IN YOUR PC CASE

Carefully lift your graphics card with installed block and insert it in your PC’s motherboard PCI-express expansion slot. Please bear in mind that your graphics card is probably

heavier than when it was equipped with original heat sink fan assembly. One needs to be very careful when handling the graphics card. Avoid all un-needed manipulation of

the VGA/water block assembly that might damage your card or water block during final installation.

REQUIRED TOOLS:

scissors Philips head screwdriver

M2,5 p2-x4

PVC washer

EK-CSQ Fing

Tubing

EK-Plug G1/4

Acetal Terminal