EK Water Blocks EK-FC780 GTX WF3 Manual de Usario

EK Water Blocks Refrigeración de hardware EK-FC780 GTX WF3

Lee a continuación 📖 el manual en español para EK Water Blocks EK-FC780 GTX WF3 (2 páginas) en la categoría Refrigeración de hardware. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

All disclosures, noces and warranty condions are being wrien on the EKWB website. Please read terms of use. Released on 2 nd April, 2014. Revision 1.0 of

Installation and mounting manual for EK-FC780 GTX water block WF3

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at for updates. Before www.ekwb.com

installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual before through before beginning with the installation process!

2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).

3. The EK High Flow and EK-PSC type fittings require only a small amount of force to screw them firmly place since the liquid seal is ensured by the rubber O-ring gaskets.in

4. The use of corrosion inhibiting coolants is always recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION. Sample picture of Gigabyte GeForce GTX 780 WF3 series

STEP 2 : PREPARING YOUR GRAPHIC CARD

REMOVING STOCK COOLER: Remove the stock GPU HSF assembly. Remove all

encircled screws attaching VRM and VRAM heatsink to the circuit board. There

are 7 (seven) screws on the back of the graphics card.

STEP 2 cont.: PREPARING YOUR GRAPHIC CARD

2 cont.: REMOVING FACTORY PROVIDED SIDE BRACKET. Remove 3 encircled screws on .

the front of circuit board. Simply remove the side bracket.

2. CLEANING THE PCB. Carefully detach the original stock cooler after removing all

screws securing it to the board. Wipe off the remains (by using non abrasive cloth –

qtip

, as shown on sample photo) of the original thermal compound until the

components and circuit board are completely clean. EKWB recommends the use of

denatured alcohol for removing TIM leftovers.

3. APPLYING THERMAL COMPOUND. Wipe off the

remains (by using non abrasive cloth or –

qtip

) of the

original thermal compound until the components and

circuit board are completely clean. Apply thermal

compound: lightly coat

NVIDIA

GPU chip with enclosed

EK-TIM Ectotherm thermal grease. EKWB recommends to

apply thermal grease in cross form for best performance

(see sample picture).

4. CUTTING THERMAL PADS. Your block comes with thermal pads, some of which are already pre-cut. Others

have to be cut to smaller chunks in order to cover all the VRM components such as MOSFETs and drivers. PLEASE

REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION.

Replacement thermal pads: Thermal Pad D 0.5mm (RAM 8x), Thermal Pad A 0.5mm. – –

STEP 3: INSTALLING THE WATER BLOCK

1. PLACING THERMAL PADS ON PCB. Place thermal pads on chips so that numbers on chips match size of thermal pads You may use small drops of electrically non-.

conductive (for example: -TIM Ectotherm, Arctic Cooling MX-2 -EK ™ or GELID GC Extreme™) thermal grease on each phase regulator (that is being covered with thermal

pad) in order to even further improve the thermal performance of the EK-FC780 GTX WF3 series water block.

2: Thermal pad A – 0.5mm

(for VRM/MOSFET):

1: Thermal pad D –0.5mm

(for memory IC):

All disclosures, noces and warranty condions are being wrien on the EKWB website. Please read terms of use. Released on 2 nd April, 2014. Revision 1.0 of

2. PLACING BLOCK TO GRAPHIC CARD. Carefully position the water block with

preinstalled 2.5 mm standoffs on to the graphics card. During this process please make

sure you align mounting holes on PCB with holes on the water block. Also pay attention

not to use too much force by pressing block down to PCB. Chip dies are prone to

cracking.

3. ATTACHING BLOCK TO GRAPHIC CARD. By using Philips screwdriver screw in

enclosed M3x4 DIN7985 screws EKWB recommends users to art tightening the . st

screws around the GPU core and continue outwards. Always use a plastic washer

under each and every screw!

STEP 4: CHECKING FOR CONTACTS

If necessary temporarily r

emove the water block to check for uniform surface contact between the block and the components, pay special attention to the VRM section of the

graphics card. Check whether the water block makes contact with the intended integrated cirucit. Then repeat sub-steps in previous section to re-attach the block. In case you

fail to obtain good contact, please check again your thermal pad thickness or contact our support service at http://www.ekwb.com/support.

STEP 5: INSTALLATION OF FITTINGS AND TUBING

This page is intenonally le blank

Screw in the two G1/4 threaded male fittings. Attach the liquid cooling tubes and connect

the water-block(s) into the cooling circuit. EKWB recommends using EK-PSC fittings

with the EK-FC780 GTX WF3 series water blocks. To ensure that the tubes are

securely attached to the barb/fittings, please use hose clamps or an appropriate substitute.

You can use any opening as an inlet/outlet port.

CAUTION: In case of using connectors other than EK-PSC series compression fittings take

special attention to the length of the fittings’ male G1/4” thread. In case the thread is longer

than 5mm please use the enclosed 1.8mm nickel plated distancer!

5mm is the maximum allowed G1/4” thread length!

STEP 7: INSERTING CARD IN YOUR PC CHASSIS

Carefully lift your graphics card with installed block and insert it in your PC’s

motherboard PCI-express expansion slot Please bear in mind that your graphics .

card is probably heavier than when it was equipped with original heat sink fan

assembly. One needs to be very careful when handling the graphics card. Avoid

all un-needed manipulation of the VGA/water block assembly that might damage

your card or water block during final installation.

REQUIRED TOOLS:

scissors Philips screwdriver

EK-PSC Fing

Tubing

EK-Plug G1/4

Acetal Terminal

Screw M3x4 DIN7985

EK Plasc washer

If white washers are factory glued on circuit board do NOT remove them.

Simply use them instead of EK enclosed plasc washers where present.

Especificaciones del producto

Marca:	EK Water Blocks
Categoría:	Refrigeración de hardware
Modelo:	EK-FC780 GTX WF3
Color del producto:	Zwart
Peso.:	300 g
Ancho:	66 mm
Profundidad:	100 mm
Altura:	20 mm
Tipo de enchufe:	Type M
Peso del embalaje:	400 g
Ancho del embalaje:	160 mm
Empaquetadura en profundidad:	125 mm
Altura del embalaje:	65 mm
Manual de usuario:	Ja
Indicadores LED:	Ja
Resolución Máxima:	4096 x 2160 Pixels
Certificación:	CE, FCC, REACH
HDCP:	Ja
Velocidad máxima de actualización:	60 Hz
Conexión para adaptador de red:	Ja
Material:	Metaal
Versión HDMI:	2.0
Resoluciones de gráficos compatibles:	1280 x 720 (HD 720),1920 x 1080 (HD 1080),1920 x 1200 (WUXGA),2560 x 1600 (WQXGA),3840 x 2160,4096 x 2160
Certificados de sostenibilidad:	RoHS
Número de DisplayPorts:	1
Temperatura de almacenamiento:	-20 - 70 °C
Canales de salida de audio:	7.1 kanalen
Adaptador de CA, voltaje de salida:	5 V
Adaptador de CA, potencia de salida:	1 A
Entrada HDMI:	3
Versión HDCP:	2.2
Incluyendo tornillos:	Ja
Soportes de montaje incluidos:	Ja
Número de salidas HDMI:	1
Conexión de vídeo:	HDMI/DisplayPort
Mando a distancia incluido:	Ja
voltaje-de-entrada-de-CA:	100 - 240 V
Temperatura de funcionamiento (TT):	0 - 45 °C
Humedad relativa de funcionamiento (VV):	10 - 90 procent
Código del Sistema Armonizado (SA):	85176990
Adaptador de CA de alimentación de entrada:	0.3 A
3,5 mm en:	Ja
Tipo de adaptador de enchufe:	NA/JP, UK, EU, ANZ