Emko Eco PID Manual de Usario
Emko
Controlador de temperatura
Eco PID
Lee a continuación 📖 el manual en español para Emko Eco PID (4 páginas) en la categoría Controlador de temperatura. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/4
3
2
1
PO1
AL2
°C
°F
/
Eco
PO2
AL1
PO1
AL2
°C
°F
/
Eco
PO2
AL1
45
6
Eco PID, PID Temperature Control Un t�
- 3 d g t process (PV) and 4 d g t set (SV) d splay� � � � �
- Temperature sensor nput (TC,RTD)�
- Programmable ON/OFF, P, PI, PD and PID control forms
- Adaptat on of PID Coeff c ents to the system w th Self-Tune and Auto-Tune � � � �
- Programmable Heat ng or Cool ng Funct ons for Control Output � � �
- Selectable Alarm Funct ons for Alarm Output�
- Ser al RS485 Commun cat on (opt onal)� � � �
Introduct on Brochure. ENG EcoPID 01 V04 10/19�
Easy Access D agram For Program Parameters�
Panel Mount ng�
Enter Password w th ncrement� �
or decrement buttons.
Approve password
w th Enter button�
Ma n Screen Password Screen�
Eco ser es temperature controllers are des gned for measur ng and controll ng a � � � �
temperature value. They can be used n many appl cat ons w th the r TC and RTD � � � � �
temperature measurement nput, mult -funct on control outputs, selectable alarm � � �
funct ons.�
They are ma nly used � �n glass, plast c, petro-chem stry, text le, automot ve and mach ne � � � � �
product on � � �ndustr es. Accurate and advanced controll ng � �s performed w th selectable �
ON-OFF, P, PI, PD, PID and Self Tune/Auto Tune PID funct ons.�
SPECIFICATIONS
Process Input: Thermocouple (TC): J, K, R, S, T and L (IEC584.1)(ITS90)
Thermores stance (RTD): Cu-50 and PT-100 (IEC751)(ITS90)�
Measurement Range: Please refer to process �nput type select on � �n process menu
parameters sect on.�
Accuracy:
Thermocouple (TC):( ± 0.25% of full scale or ± 3ºC, wh ch one � �s greater) ±1 d g t max. � �
Thermores stance (RTD):( ± 0.25% of full scale or ± 2ºC, wh ch one � � �s greater) ±1 d g t � �
max.
Cold Junct on Compensat on:� � Automat cally ±0.1°C/1°C�
L ne Compensat on:� � Max mum 10 Ohm�
Sensor Break Protect on:� Upscale
Sampl ng Cycle: �0.1 second
Input F lter:� Programmable
Control Form: ON/OFF, P, PI, PD or PID (Control form can be programmed by the user)
OUTPUT
Process Output: Relay (5A@250V at res st ve load) or SSR Dr ver Output V� � �
(Max mum 10mA, Max. 12V )�Z
Alarm Output: Relay (5A@250V at res st ve load)V� �
SUPPLY VOLTAGE (It must be determ ned � �n order)
230V (±15%) 50/60Hz - 2VAV
115V (±15%) 50/60Hz - 2VAV
100-240V 50/60Hz - 2VAV
24V (±%15) 50/60Hz - 2VAV
24V (±%15) 50/60Hz - 2VAW
10...30V - 2WZ
DISPLAY
Process D splay:� 16 mm Red 3 d g t LED D splay� � �
Set Value D splay:� 9 mm Orange 4 d g t LED D splay� � �
Led Ind cators:� PO1 (SSR Process Output Status Led), PO2 (Relay
Process Output Status Led), AL1, AL2 (Alarm Output Status Leds),
ºC, ºF LEDs
ENVIRONMENTAL RATINGS and PHYSICAL SPECIFICATIONS
Operat ng Temperature:� 0...50ºC
Hum d ty :� � 0-90%RH (none condens ng)�
Protect on Class: �IP65 at front, IP20 at rear
We ght:� 150 gr.
D mens on:� � 48 x 48 mm, Depth: 86,5 mm
Panel CutOut: 46 x 46 mm
*1 - ON/OFF Hysteres s parameter s not act ve unless parameter s set as .� � � �
*2 - Soft Start parameters( , , ) s not act ve unless parameter s set as .� � �
*3 - Soft Start Control Output and Soft Start Control T me parameters s not act ve f parameter� � � �
s set as .�
*4 - PID control parameters are not act ve unless parameter s set as .� �
*5 - Alarm-2 parameters are not act ve f parameter s set as .� � �
*6 - Commun cat on parameters are not act ve on dev ces have no commun cat on module.� � � � � �
*7 - If s d fferent from 0 and user enters to program menu w thout enter ng the password� � � �
Prot menu s not shown.�
Note: User can ex t from any parameter screen w thout sav ng the values by press ng button. If � � � �
no operat on for 120 seconds, dev ce automat cally return to ma n screen.� � � �
Easy Access D agram For Sensor Break Output�
Value From Ma n Screen�
Change the sensor break
output value w th ncrement� �
or decrement buttons.
Press Enter button to save
new sensor break output value
and ex t.�
PO2
PO1
AL1
AL2
°C
°F
/
Ma n Screen�
PO2
PO1
AL1
AL2
°C
°F
/ PO2
PO1
AL1
AL2
°C
°F
/ PO2
PO1
AL1
AL2
°C
°F
/
Ma n Screen�
Note1: User can ex t from parameter screen w thout sav ng the � � �
values by press ng button. If no operat on for 120 seconds, dev ce � � �
automat cally ex ts from parameter screen.� �
Note2: Sensor break output value can be adjusted on programm ng �
sect on too.�
Tune Operat on�
Start ng the Tune operat on� �
1- Enter to the parameter n menu and select �
or ,then press button for sav ng parameter and turn to ma n � �
screen. Or eas ly press button for 3 seconds* n ma n screen.� � �
2- Observe that bl nks n set d splay.� � �
*Only Auto tune can be started by th s way.�
Cancel ng Tune operat on:� �
1- If sensor breaks;
2- If tune operat on can not be completed n 8 hours;� �
3- Wh le heat ng self tune s runn ng, f process value becomes � � � � �
greater than process set value;
4- Wh le cool ng self tune s runn ng, f process value becomes less � � � � �
than process set value;
5- Wh le tune operat on s runn ng, f user changes the process set � � � � �
value;
6- Wh le tune operat on s runn ng, f user changes the � � � � �
parameter n menu; �
Then tune operat on s canceled, dev ce cont nues to run w th former � � � � �
PID parameters w thout chang ng PID parameters.� �
PID TEMPERATURE CONTROL UNIT
PID
Eco
D mens ons� �
PO2
PO1 AL1
AL2
°C
°F
/
PID
Eco
48 mm / 1.89 nch�
48 mm / 1.89 nch�
6 mm / 0.24 nch�80,52 mm / 3.17 nch�
Max mum 9 mm / 0.35 nch� �
1- Before mount ng the dev ce n your panel, � � �
make sure that the cutout s of the r ght s ze.� � �
2- Check front panel gasket pos t on.� �
3- Insert the dev ce through the cutout. If the �
mount ng clamps are on the un t, put out them � �
before nsert ng the un t to the panel.� � �
4- Insert the mount ng clamps to the two of �
des gnated holes that located four s des of � �
dev ce. �
5- Drag the mount ng clamps n d rect on 5 � � � �
unt l the dev ce completely mmob le w th n the � � � � � �
panel.
6- In order to remove dev ce push on the �
mount ng clamp as shown w th arrow 6 and � �
pull back.
Access and Change Set Values
Press ncrement or decrement�
button to change process set value.
Press Enter button to save new
set value and return the ma n screen.�
Ma n Screen�
PO2
PO1
AL1
AL2
°C
°F
/PO2
PO1
AL1
AL2
°C
°F
/
Ma n Screen�
PO2
PO1
AL1
AL2
°C
°F
/ PO2
PO1
AL1
AL2
°C
°F
/
Temperature Set Value Parameter (Default: 200) MODBUS ADDRESS: 40000
a
Note-1: User can ex t from set value sect on w thout sav ng the values by press ng button. If no � � � � �
operat on for 120 seconds, dev ce automat cally ex ts from Set Value sect on.� � � � �
Note-2: Set value can be adjusted between Set Value Low and H gh L m t ( - ).� � �
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/ PO2
PO1
AL1
AL2
°C
°F
/PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
*1
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
*5
*2
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
*4
*2,3
*2,3
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
*7
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
*6
PO2
PO1
AL1
AL2
°C
°F
/
Press Program button
to access password screen.
Electr cal W r ngs� � �
The Dev ce w th One Relay:� �
The Dev ce w th Two Relays:� �
To reduce the effect of electr cal no se on dev ce, low voltage l ne (espec ally sensor � � � � �
� � � � � �nput cable) w r ng must be separetely from h gh current and voltage l ne. If poss ble,
use sh elded cable and sh eld must be connected to ground only one s de.� � �
c
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PO1
(Process Output 1)
SSR Output
12V
Max. 10mA
C
NO AL1 / PO2
(Alarm Output 1 or
Process Output 2)
Process
Input
5A@250V
Ser al Commun cat on� � �
(RS485, Modbus RTU) A+
B-
PID
Eco
PT-100
TC
Supply
Sw tch�
L
N
Supply
Voltage
1A T
Fuse
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PO1
(Process Output 1)
SSR Output
12V
Max. 10mA
C
NO
NO
AL1
(Alarm Output 1)
AL2 / PO2
(Alarm Output 2 or
Process Output 2)
Process
Input
5A@250V
5A@250V
Ser al Commun cat on� � �
(RS485, Modbus RTU) A+
B-
PID
Eco
PT-100
TC
Supply
Sw tch�
L
N
Supply
Voltage
1A T
Fuse
Warranty
EMKO Elektron k warrants that the equ pment del vered s free from � � � �
defects n mater al and workmansh p. Th s warranty s prov ded for a � � � � � �
per od of two years. The warranty per od starts from the del very � � �
date.
Th s warranty s n force f duty and respons b l t es wh ch are � � � � � � � � �
determ ned n warranty document and nstruct on manual performs � � � �
by the customer completely.
Ma ntenance�
Repa rs should only be performed by tra ned and spec al zed � � � �
personnel. Cut power to the dev ce before access ng nternal parts. � � �
Do not clean the case w th hydrocarbon-based solvents (Petrol, �
Tr chlorethylene etc.). Use of these solvents can reduce the �
mechan cal rel ab l ty of the dev ce. Use a cloth dampened n ethyl � � � � � �
alcohol or water to clean the external plast c case.�
Other Informat ons�
Manufacturer Informat on:�
Emko Elektron k Sanay ve T caret A. .� � � Ş
Dem rta Organ ze Sanay Bölges Karanf l Sk. No:6 16369 � ş � � � �
BURSA/TURKEY
Phone: +90 224 261 1900
Fax: +90 224 261 1912
a
Repa r and Ma ntenance Serv ce Informat on:� � � �
Emko Elektron k Sanay ve T caret A. .� � � Ş
Dem rta Organ ze Sanay Bölges Karanf l Sk. No:6 16369 � ş � � � �
BURSA/TURKEY
Phone: +90 224 261 1900
Fax : +90 224 261 1912
Before comm ss on ng the dev ce, parameters must be set n � � � � �
accordance w th des red use. Incomplete or ncorrect conf gurat on � � � � �
can cause dangerous st uat ons.� �
Because of l m ted mechan cal l fe of relay output contact, SSR � � � �
output s recommended wh ch the dev ce use PID control algor tm. � � � �
The dev ce w th ON/OFF control algor tm, hysteres s parameter must � � � �
be set a su table value for your system, to avo d too much relay � �
sw tch ng.� �
Vac,
Vdc,
Vdc or Vac can be appl ed�
: Commun cat on Parameters � � (Only for dev ces w th RS-485 com.)� �
: Protec on Menu Parameters�
: Commun cat on access ng address of dev ce. (Default: 1) Modbus � � � �
Address: 40056
: Commun cat on Baud Rate. (Default: 3) Modbus Address: 40057� �
: 1200 Baud Rate.
: 2400 Baud Rate.
: 4800 Baud Rate.
: 9600 Baud Rate.
: 19200 Baud Rate.
: 38400 Baud Rate.
: Par ty Select on for Commun cat on. (Default: 0) Modbus Address: 40058� � � �
: No Par ty.�
: Odd Par ty.�
: Even Par ty.�
: Stop B t Select on for Commun cat on. (Default: 0) Modbus Address: 40059� � � �
: 1 Stop B t.�
: 2 Stop B t.�
: Password for access ng to the programm ng sect on. It can be adjusted from 0 to � � �
9999. If s 0, password screen s not seen. If s d fferent from 0 and user � � � �
enters to the menu pages w thout enter ng the password, all the menus can be � �
observed except protect on menu . But dev ce does not allow to do any changes � �
�n parameters. (Default: 0) Modbus Address: 40063
: User default parameters. Th s parameter s used for sav ng all parameters to � � �
restore later or restore all parameters saved before. If s chosen, all parameters �
saved before are restored. If s chosen, all parameters saved to restore later. If�
� � �s chosen, noth ng s changed. (Default: ) Modbus Address: 40064
: Th s parameter s used for restore factory defaults. If s chosen, factory � � �
defaults parameters restored. If s chosen, noth ng s changed. (Default: ) � � �
Modbus Address: 40065
Remove all nput/output connect ons on term nals before restor ng � � � �
parameters to user/factory defaults.
c
Modbus Addresses of Dev ce Operat on Info. (Read Input Reg ster)� � �
Modbus Address: 30000
Modbus Address: 30001
Modbus Address: 30002
D splayed Temperature Value�
Status of LEDs: b t.1 , b t.2 , b t.9 �ALR1 �ALR2 �°C
b t.10 , b t.11 , b t.12 �°F �PO2 �PO1
Status of Dev ce: b t.0 Sensor Break Status� �
Alarm Types
Alarm
Set
Alarm
Hysteres s�
Alarm
Hysteres s�
Alarm
Set
Process
Set
Process
Set
Alarm
Set
Alarm
Hysteres s�
Alarm
Hysteres s�
Process
Set
Process
Set
Alarm
Set
Alarm
Output
Alarm
Output
Alarm
Output
Alarm
Output
Process Value
Process Value
Process Value
Process Value
Process H gh�
Alarm
Process Low
Alarm
Dev at on H gh� � �
Alarm
Dev at on Low� �
Alarm
: Alarm-1 set value. (Default: 300) Modbus Address: 40036
: Alarm-1 hysteres s value. It can be adjusted from %0 to %50 of the scale�
( - ). (Default: 0) Modbus Address: 40037
: Alarm-1 type select on. (Default: ) Modbus Address: 40038�
: Alarm-1 set low l m t parameter. It can be adjusted from operat on scale m n mum � � � � �
to alarm-1 set h gh l m t. (Default: 0) Modbus Address: 40039� � �
: Alarm-1 set h gh l m t parameter. It can be adjusted from alarm-1 set low l m t to � � � � �
operat on scale m n mum. (Default: 500) Modbus Address: 40040� � �
: Alarm-1 on Delay T me. It can be adjusted from 0 to 9999 seconds. (Default: 0) �
Modbus Address: 40041
: Alarm-1 off Delay T me. It can be adjusted from 0 to 9998 seconds. If t s h gher � � � �
than 9998, s seen on the screen and alarm latch ng output s selected. In alarm � � �
latch ng output mode n order to make pass ve alarm outputs, press enter button at � � �
ma n screen. (Default: 0) Modbus Address: 40042�
: Alarm-1 Menu Parameters
PID menu parameters can be seen only f parameter s .� �
: If tune parameter s set to or , dev ce start to calculate PID � �
parameters automat cally. (Default: ) Modbus Address: 40027�
: Proport onal band. It can be adjusted from %1.0 to %100.0. (Default: 10.0) �
Modbus Address: 40028
: Integral T me. It can be adjusted from 0 to 3600 second. (Default: 100) Modbus �
Address: 40029
: Der vat ve T me. It can be adjusted from 0.0 to 999.9 second. (Default: 25.0) � � �
Modbus Address: 40030
: Output Control Per od. It can be adjusted from 0.5 to 150 second. (Default: 1.0) �
Modbus Address: 40031
: Set value offset. (Set + ) s used as set value n PID calculat ons. Th s � � � �
parameter s used for sh ft ng the proport onal band. It can be adjusted from (- /2) to � � � �
( /2). (Default: 0) Modbus Address: 40032
: PID Menu Parameters
: Alarm-2 Menu Parameters (Only for dev ces w th two relays)� �
Alarm-2 menu parameters can be seen only f parameter s .� �
: Alarm-2 set value. (Default: 400) Modbus Address: 40046
: Alarm-2 hysteres s value. It can be adjusted from %0 to %50 of the Scale�
( - ). (Default: 0) Modbus Address: 40047
: Alarm-2 type select on. (Default: ) Modbus Address: 40048�
: Alarm-2 set low l m t parameter. It can be adjusted from operat on scale m n mum � � � � �
to alarm-2 set h gh l m t. (Default: 0) Modbus Address: 40049� � �
: Alarm-2 set h gh l m t parameter. It can be adjusted from alarm-2 set low l m t to � � � � �
operat on scale max mum. (Default: 500) Modbus Address: 40050� �
: Alarm-2 on delay t me. It can be adjusted from 0 to 9999 seconds. (Default: 0) �
Modbus Address: 40051
: Alarm-2 off delay t me. It can be adjusted from 0 to 9998 seconds. If t s h gher � � � �
than 9998, s seen on the screen and Alarm Latch ng Output s selected. In � � �
alarm latch ng output mode n order to make pass ve alarm outputs, press enter � � �
button at ma n screen. (Default: 0) Modbus Address: 40052�
Installat on�
In package,
-One p ece un t� �
-Two p eces mount ng clamp� �
-One p ece nstruct on manual� � �
A v sual nspect on of th s product for poss ble damage occured � � � � �
dur ng sh pment s recommended before nstallat on. It s your � � � � � �
respons b l ty to ensure that qual f ed mechan cal and electr cal � � � � � � �
techn c ans nstall th s product.� � � �
If there s danger of ser ous acc dent result ng from a fa lure or defect � � � � �
� � � � �n th s un t, power off the system and the electr cal connect on of the
dev ce from the system.�
The un t s normally suppl ed w thout a power sw tch or a fuse. Use � � � � �
power sw tch and fuse as requ red.� �
Be sure to use the rated power supply voltage to protect the un t �
aga nst damage and to prevent fa lure.� �
Keep the power off unt l all of the w r ng s completed so that electr c � � � � �
shock and trouble w th the un t can be prevented.� �
Never attempt to d sassemble, mod fy or repa r th s un t. Tamper ng � � � � � �
w th the un t may results n malfunct on, electr c shock or f re.� � � � � �
Do not use the un t n combust ble or explos ve gaseous � � � �
atmospheres. Dur ng the equ pment s putted n hole on the metal � � � �
panel wh le mechan cal nstallat on some metal burrs can cause � � � �
�njury on hands, you must be careful.
Montage of the product on a system must be done w th t’s mount ng � � �
clamp. Do not do the montage of the dev ce w th nappropr ate � � � �
mount ng clamp. Be sure that dev ce w ll not fall wh le do ng the � � � � �
montage.
It s your respons b l ty f th s equ pment s used n a manner not � � � � � � � � �
spec f ed n th s nstruct on manual.� � � � � �
Before beg nn ng nstallat on of th s product, please � � � � �
read the nstruct on manual and warn ngs below � � �
carefully.
Error Messages
Dev at on Range� �
H gh Alarm�
Process
Set
Alarm
Set
Process
Set
Alarm
Hysteres s�
Alarm
Output
Process Value
Process
Set
Alarm
Set
Process
Set
Process
Set
Alarm
Set
Alarm
Hysteres s�
Alarm
Hysteres s�
Alarm
Output
Process Value
Dev at on Range� �
Alarm
1-Sensor fa lure n analog nputs. Sensor connect on s wrong or there � � � � �
� �s no sensor connect on.
a
2-If programm ng sect on enter ng password s d fferent from “0” and � � � � �
user accesses to the parameter by enter button w thout enter ng the � �
password and wants to change a parameter, the warn ng message s � �
shown on the bottom d splay as shown on the left. Dev ce does not � �
allow to do any changes w thout enter ng the password correctly.� �
a
3-If value that s read from the analog nput s lower than process set � � �
low l m t parameter value ( ), value on the top d splay starts to bl nk � � � �
as shown on the p cture.�
a
4-If value that s read from the analog nput s h gher than process set � � � �
h gh l m t parameter value ( ), value on the top d splay starts to � � � �
bl nk as shown on the p cture.� �
a
5-If value that s read from the analog nput s lower than sensor scale � � �
low l m t, value on the top d splay starts to bl nk as shown on the � � � �
p cture.�
a
6-If value that s read from the analog nput s h gher than sensor scale � � � �
h gh l m t, value on the top d splay starts to bl nk as shown on the � � � � �
p cture.�
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
PO2
PO1
AL1
AL2
°C
°F
/
Process
Set
Alarm
Set
Process
Set
Process
Set
Alarm
Set
Alarm
Hysteres s�
Alarm
Hysteres s�
Alarm
Output
Process Value
Dev at on Band� �
Alarm
: Control Menu Parameters
: Th s parameter determ nes, wh ch output w ll be Process control output. If s � � � � �
chosen, process output s relay output, f s chosen, process output s SSR output. � � � �
(Default: ) Modbus Address: 40015
: Process Type Select on. It can be (Heat ng) or (Cool ng).(Default: ) � � �
Modbus Address: 40016
: Process Control Type Select on. It can be or . (Default: ) Modbus �
Address: 40017
: Hysteres s value. It can be adjusted from %0 to %50 of the Scale ( - ). �
If = , then th s parameter can be seen. (Default: 3) Modbus Address: 40018�
: Sensor Break Output Value. It can be adjusted from %0 to %100. (Default: 0.0)
Modbus Address: 40019
: The cho ce of d splayed text on process value d splay when sensor s broken.� � � �
It can be or . (Default: ) Modbus Address: 40020
: Soft Start Set value. Dev ce operates n Soft Start mode, unt l the temperature � � �
reaches Soft Start set value. If s selected, Soft Start mode s d sabled. (Default: )� � �
Modbus Address: 40021
: Soft Start Control Output. Th s parameter determ nes soft start mode control � �
output percentage. It can be adjusted from %10 to %90. (Default: 10.0) Modbus
Address: 40022
: Soft Start Control T me. Th s parameter determ nes soft start mode control t me. � � � �
(Default: 1.0) Modbus Address: 40023
: Process Menu Parameters
: Process nput type select on; (Default: ) Modbus Address: 40004� �
: J type (Fe,Cu,N ) Thermocouple , -199ºC,900ºC ; -199ºF,999ºF�
: J type (Fe,Cu,N ) Thermocouple , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF�
: K type (N ,Cr,N ) Thermocouple , -199ºC,999ºC ; -199ºF,999ºF� �
: K type (N ,Cr,N ) Thermocouple , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF� �
: R type (Pt13%RhPt) Thermocouple , 0ºC,999ºC ; 32ºF,999ºF
: R type (Pt13%RhPt) Thermocouple , 0.0ºC,99.9ºC ; 32.0ºF,99.9ºF
: S type (Pt10%RhPt) Thermocouple , 0ºC,999ºC ; 32ºF,999ºF
: S type (Pt10%RhPt) Thermocouple , 0.0ºC,99.9ºC ; 32.0ºF,99.9ºF
: T type (Cu,Cu,N ) Thermocouple , -199ºC,400ºC ; -199ºF,752ºF�
: T type (Cu,Cu,N ) Thermocouple , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF�
: L type (N ,Cr,Co / N ,Fe,Mn,Cu) Thermocouple , -150ºC,800ºC ; -199ºF,999ºF� �
: L type (N ,Cr,Co / N ,Fe,Mn,Cu) Thermocouple , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF� �
: Cu-50 , -199ºC,200ºC ; -199ºF,392ºF
: Cu-50 , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF
: Pt-100 , -199ºC,650ºC ; -199ºF,999ºF
: Pt-100 , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF
: Un t Select on. or can be chosen. (Default: ) Modbus Address: 40005� �
: Operat on Scale m n mum (Low L m t) value. It changes accord ng to the process� � � � � �
�nput type and scale. (Default: -199) Modbus Address: 40006
: Operat on Scale max mum (H gh L m t) value. It changes accord ng to the� � � � � �
process nput type and scale. (Default: 900) Modbus Address: 40007�
: Process Set value Low L m t. M n mum set value s def ned w th th s parameter.� � � � � � � �
It can be adjusted between Operat on Scale m n mum and max mum ( - ) � � � �
values. (Default: -199) Modbus Address: 40008
: Process Set value H gh L m t. Max mum set value s def ned w th th s parameter.� � � � � � � �
It can be adjusted between Operat on Scale m n mum and max mum ( - ) � � � �
values. (Default: 900) Modbus Address: 40009
: D splay offset for process value. It can be adjusted from -10% of scale to 10% of�
scale. It s added to the process d splay value. (Default: 0) Modbus Address: 40010� �
: Def ne f lter t me(sec) for d splayed value. (Default: 1.0) Modbus Address: 40011� � � �
Order ng Informat on� �
Eco PID ( 48x48 DIN 1/16 )
D mens on� �
48x48 DIN 1/16
A
4
A
4 .
B
.
C
.
D
S .
E
Outputs-1
1R 1 x Relay Output (5A@250V at Res st ve Load) (NO,C)V� �
C
2R 2 x Relay Output (5A@250V at Res st ve Load) (NO,NO,C)V� �
S SSR Dr ver Output (Max. 10mA, Max. 12V )�Z
Outputs-2D
Commun cat on� �
0 None
485 RS-485 Commun cat on� �
E
10...30VZ
115V (±%15) 50/60HzV
230V (±%15) 50/60HzV
3
5
6
100-240V 50/60Hz1 V
24V (±%15) 50/60HzV
Customer
7
9
24V (±%15) 50/60Hz2 W
Supply VoltageB
Especificaciones del producto
| Marca: | Emko |
| Categoría: | Controlador de temperatura |
| Modelo: | Eco PID |
¿Necesitas ayuda?
Si necesitas ayuda con Emko Eco PID haz una pregunta a continuación y otros usuarios te responderán
Controlador de temperatura Emko Manuales
12 Septiembre 2024
12 Septiembre 2024
12 Septiembre 2024
12 Septiembre 2024
26 Agosto 2024
22 Agosto 2024
Controlador de temperatura Manuales
- Controlador de temperatura Voltcraft
- Controlador de temperatura Dimplex
- Controlador de temperatura Ventus
- Controlador de temperatura Technoline
- Controlador de temperatura Inkbird
- Controlador de temperatura Bulex
- Controlador de temperatura Fluke
- Controlador de temperatura Jung
Últimos Controlador de temperatura Manuales
2 Octubre 2024
30 Septiembre 2024
27 Septiembre 2024
20 Septiembre 2024
19 Septiembre 2024
19 Septiembre 2024
18 Septiembre 2024
17 Septiembre 2024
15 Septiembre 2024
9 Septiembre 2024