EMOS P5763 Manual de Usario

EMOS Timbre de la puerta P5763

Lee a continuación 📖 el manual en español para EMOS P5763 (75 páginas) en la categoría Timbre de la puerta. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/75

3402060001_31-P5763_00_01_WEB 80 × 120 mm

www.emos.eu

P5763

GB Wireless Doorchime & Repeater

CZ Bezdrátový zvonek & prodlužovač signálu

SK Bezdrôtový zvonček & predlžovač signálu

PL Dzwonek bezprzewodowy & repeater sygnału

HU Vezeték nélküli csengő és jelismétlő

SI Brezžični zvonec in ojačevalnik signala

RS|HR|BA|ME Bežično kućno zvono i repetitor

DE Drahtlose Klingel und Signalverlängerung

UA Бездротовий дзвоник & подовжувач сигналу

RO|MD Sonerie fără r & prelungitor de semnal

LT Belaidis durų skambutis ir retransliatorius

LV Bezvadu durvju zvans un atkārtotājs

EE Juhtmevaba uksekell ja repiiter

BG Безжичен звънец и повторител

FR Carillon sans l & prolongateur de portée

IT Campanello senza li & ripetitore di segnale

ES Timbre inalámbrico & repetidor de señal

NL Draadloze deurbel & signaalverlenger

3 6

A B C

GB | Wireless Doorchime & Repeater

The set consists of a doorchime button (transmitter) and a chime (receiver). The chime is powered by

3× 1.5 V AA batteries.

The transmission between the button and the chime is done via radio waves at a frequency of 433.92 MHz. The

range depends on local conditions and reaches up to 120 m in open spaces without interference.

The set has a so-called “self-learning” function – the button is able to generate its own pairing code which is

then received by the chime and stored in its memory. The set can thus be expanded with additional buttons.

Their “self-learning” function also prevents them from aecting neighbouring doorchimes.

The range of the button can be extended using the “repeater” function (signal repeater).

For proper usage of the wireless doorchime, read the instruction manual thoroughly.

Technical Specications

Transmission range: up to 120 m in an open area (can drop down to one fth in a busy area)

Button: water resistant; enclosure IP44

Pairing of chime and buttons: “self-learning” function

Pairing capacity: max. 8 buttons per 1 chime

Number of ringtones: 16

Transmission frequency: 433.92 MHz, 5 mW e.r.p. max.

Chime power supply: 3× 1.5 V AA batteries

Button power supply: 1× 3 V battery (type CR2032, included)

Includes: double-sided adhesive tape, screws

Chime Description (see Fig. 1)

1 – chime LED

2 – speaker

3 – ringing mode button

4 – volume settings button

5 – repeater button (signal repeating)

6 – opening for hanging on a wall

7 – battery compartment

Button Description (see Fig. 2)

A – battery

B – button for changing ringtone/erasing memory of paired buttons

C – ring button/LED

Opening the Rear Compartment of the Button (see Fig. 3)

Pairing the Button with the Chime

1. Remove the rear cover of the button with a screwdriver through the hole on the side (see Fig. 3).

Insert a 3 V battery, type CR2032, into the button. When inserting the battery, make sure to observe correct

polarity (+ polarity up)!

2. Insert 3× 1.5 V AA batteries into the battery compartment of the doorbell (use alkaline batteries only).

You will hear a “ding dong” tone.

The chime automatically switches to “self-learning” mode which lasts for 60 second.

3. During these 60 seconds, press the button you want to pair with the chime. If the chime receives signal

from the button, a tone will sound, the button will pair with the chime and the self-learning mode will

automatically end.

4. For pairing multiple buttons, repeat steps 1 to 3.

Note: Before pairing each button, the chime must be put into self-learning mode – remove and reinsert

3× 1.5 V AA batteries.

You can pair a maximum of 8 buttons per chime this way.

Note: The chime has an internal memory where it stores the codes of the currently paired buttons for cases of

power failure. Once power supply to the chime is restored, the chime will automatically enter self-learning mode

for 60 seconds. However, if no signal is received within these 60 seconds (new pairing is not performed), the

chime will automatically load the codes of the previously paired buttons after self-learning mode ends. There

is thus no need to pair buttons again after a power failure.

Especificaciones del producto

Marca:	EMOS
Categoría:	Timbre de la puerta
Modelo:	P5763
Color del producto:	Black, Red
Longitud del cable:	2.2 m
Bluetooth:	Nee
Tecnología de conectividad:	Bedraad
Soporta Windows:	Windows 10, Windows 7, Windows 8, Windows Vista, Windows XP
Método de uso:	Hoofdband
Uso recomendado:	Gamen
Tipo de auricular:	Stereofonisch
Impedancia:	32 Ohm
Colocar los auriculares de los altavoces.:	Circumaural
Rango de frecuencia de los auriculares:	20 - 20000 Hz
Sensibilidad de los auriculares:	103 dB
conexión USB:	Ja
Color de cables:	Zwart
Canales de salida de audio:	7.1 kanalen
Corriente de salida:	100 mA
Sensibilidad del micrófono:	111 dB
Impedancia de entrada del micrófono:	42 Ohm
Tipo-producto:	Headset
Micrófono con reducción de ruido:	Ja
Número de canales de la unidad de control:	5 kanalen