Ernitec NVR Hybrid Manual de Usario
Ernitec
Videograbadora
NVR Hybrid
Lee a continuación 📖 el manual en español para Ernitec NVR Hybrid (4 páginas) en la categoría Videograbadora. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/4
Fully understand this document before using this device, and
strictly observe rules in this document when using this device. If
you install this device in public places, provide the tip "You have
entered the area of electronic surveillance" in an eye-catching
place. Failure to correctly use electrical products may cause fire
and severe injuries.
It alerts you for moderate dangers which, if not
avoided, may cause minor or moderate injuries.
It alerts you about risks. Neglect of these risks may
cause device damage, data loss, device
performance deterioration, or unpredictable results.
It provides additional information.
ŸStrictly observe installation requirements when installing the
device. The manufacturer shall not be held responsible for
device damage caused by users' non-conformance to these
requirements.
ŸStrictly conform to local electrical safety standards and use
power adapters that are marked with the LPS standard when
installing and using this device. Otherwise, this device may be
damaged.
ŸUse accessories delivered with this device. The voltage must
meet input voltage requirements for this device.
ŸIf this device is installed in places with unsteady voltage, ground
this device to discharge high energy such as electrical surges in
order to prevent the power supply from burning out.
ŸWhen this device is in use, ensure that no water or any liquid
flows into the device. If water or liquid unexpectedly flows into
the device, immediately power off the device and disconnect all
cables (such as power cables and network cables) from this
device.
Precautions Special Announcement
For more information please refer to website.,
ŸAvoid heavy loads, intensive shakes, and soaking to prevent
damages during transportation and storage. The warranty does
not cover any device damage that is caused during secondary
packaging and transportation after the original packaging is
taken apart.
ŸProtect this device from fall-down and intensive strikes, keep the
device away from magnetic field interference, and do not install
the device in places with shaking surfaces or under shocks.
ŸClean the device with a soft dry cloth. For stubborn dirt, dip the
cloth into slight neutral cleanser, gently wipe the dirt with the
cloth, and then dry the device.
ŸDo not jam the ventilation opening. Follow the installation
instructions provided in this document when installing the device.
ŸKeep the device away from heat sources such as radiators,
electric heaters, or other heat equipment.
ŸKeep the device away from moist, dusty, extremely hot or cold
places.
ŸIf the device is installed outdoors, take insect- and moisture-
proof measures to avoid circuit board corrosion that can affect
monitoring.
ŸRemove the power plug if the device is idle for a long time.
ŸAll complete products sold by the manufacturer are delivered
along with nameplates, quick setup guide and accessories after
strict inspection. The manufacturer shall not be held responsible
for counterfeit products.
ŸThe manufacturer will update this manual according to product
function enhancement or changes and regularly update the
software and hardware described in this manual. Update
information will be added to new versions of this manual without
prior notice.
ŸThis manual may contain misprints, technology information that
is not accurate enough, or product function and operation
description that is slightly inconsistent with the actual product,
the final interpretation of company is as a standard.
ŸThis manual is only for reference and does not ensure that the
information is totally consistent with the actual product. For
consistency, see the actual product.
NOTE
ŸIf this device is installed in places where thunder and lightning
frequently occur, ground the device nearby to discharge high
energy such as thunder strikes in order to prevent device
damage.
CAUTION
NOTE
CAUTION
WARNING
WARNING
Table -2 1 Front panel description
Port Name Description
2 REC
Indicator
Hard disk status indicator.
This indicator flashes when data is transmitted.
4 MOUSE Support connecting to a USB mouse.
5 BACKUP Support connecting to a USB flash drive or USB
removable hard disk.
1 POWER
Indicator
When the XVR is operating, the POWER indicator
is steady on. When the XVR is shut down, the
POWER indicator is turned off.
Open the package, check the appearance of product for no
obvious damage, and confirm the item list for table 1-1 is
consistent.
Table 1-1 Packing list
Open Package Examination
1
2.1 Device Ports
Different devices may have different ports and multi-head
cables; Please refer to the actual product.
NOTE
D evice Structure2
2 2. Device Dimensions
Different devices may have different dimensions; Please
refer to the actual product.
NOTE
Figure 2-2 Dimensions (Unit: mm)
3 NET
Indicator
The network status indicator.
This indicator flashes when network is working.
Network Video Recorder
Phillips head screw
Power cord
Power adapter
Mouse
Quick Setup Guide
1
Terminal block
1
12
1
1
1
2
Component
Table -2 2 Rear panel description
Remark
Quantity
Optional
Optional
Front panel description of device, please refer to table 2-1.
Rear panel description of device, please refer to table 2-2.
The hard disk of the XVR must be provided by the user. Take the
following steps to install the hard disks：
Step 1 Remove the screws for fixing the cover and take down the
cover.
Step 2 Take out the screws and mount two of them to the screw
holes of hard disk, as shown in figure 3-1.
Figure -3 1 Installing the hard disk screws
3Device Installation
Step 3 Route the screws through the gourd holes on the base,
push the hard disk to the appropriate position on the left, as
shown in figure 3-2.
ŸJust screw the screws about 1 to 2 turns instead to the end.
NOTE
Figure 3-2 Installing hard disk
Step 5 Install other hard disks following step 2,step 3 and step 4,
and insert the hard disk data cable and power cable, then
replace the upper cover and fasten the fixing screws.
Figure 3-3 Fixing hard disk
Name Description
VIDEO IN Port Plug in analog camera by coaxial line.
.langis oediv golana tuptuO TUO SBVC
AUDIO OUT/
AUDIO IN
Audio output / Audio input.
LAN1/LAN2
RJ 45 100/1000 Mbps adaptive Ethernet
interface.LAN1 is deployed default gateway
and used for external network. LAN2 is used
for internal network.
Video output interface.HDMI /VGA
USB USB 2.0 port, Connect USB flash or mouse.
Alarm I/O
Alarm input/Alarm output.
Power switch.
DC12V.
Ground.
2
13
PO WE RRE C NE T
4 5
Figure 2-1 Front panel
DC 12V
372
318
46
32
76
95
32
76
95
14
16
3-M3
Step 4 Turn the device over, and mount other two screws to the
holes, as shown in figure 3-3. Then fasten all the screws.
NVR Hybrid
16 channel
Quick Setup Guide
Item no.: 0070-10403-A
Figure 4-3 Topology of the XVR
In some environments, if the power supply is abnormal,
the XVR may not work properly. In severe cases, the XVR
may be damaged. In these environments, it’s advised to
use regulated power supply.
Plug in power to access the XVR user page, the wizard window
would show at first time, user can configure quickly or close it
immediately. For details configuration please refer to main menu.
Use the mouse to right-click any where on the main interface to
access the main menu. Main menu comprises Channel, Record,
Alarm, Network and System settings, as shown in figure 5 1.-
Quick Configuration5
Device Operation
4
4.1 Startup
Before starting XVR, ensure that the XVR is connected to a power
supply properly and a monitor is connected to the HDMI or VGA
interface of the XVR correctly. After starting the XVR, there is a
login window located in the center, as shown in figure 4-1and 4-2.
CAUTION
.4 2 Topology of the XVR
XVR can access analog cameras immediately when analog
cameras are plugged into XVR’s VIDEO IN ports. Then the XVR
will assign an IP address for each camera automatically. For the
topology refer to figure 4-3.
NOTE
Figure 4-1 Activation interface
Pas sword
5.1 Channel
Channel settings contain Camera, Encode, Sensor Setting, OSD,
Privacy Zone, ROI, Microphone, Human Thermal, Smart,
Intelligent Tracking.
ŸCamera: User can add cameras automatically by clicking Click
to Add, and add manually by clicking Tick cameras then Add.
click Delete to delete cameras. User can batch update software.
Figure 4-2 Login interface
ŸUser needs to create a new password to activate the device, when
ŸUser can also set pattern unlock to quickly login. Set security
.
ŸChange the language in log in interface.
4.4 Power off
Enter the path Main Menu System Maintenance Shutdown > > > to
power off the XVR.
NOTE
ŸBefore replacing the hard disk, the power must be turned off.
ŸThe special function is only carried by some devices, if the current
device does not have the function, please ignore it.
4.3 Special Function
Click the AI Recognition icon, Human Face, or Thermal
Temperature at the bottom of local UI to enter the AI interface.
User can set and view the AI cameras’ parameters, including
human face, vehicle license plate.
Figure 5-1 Main menu
Figure 7-1 Login
Mobile Client 6
Figure 6-1 P2P
NOTE
and password are same as in the UI interface.
ŸNetwork,802.1X, , and DDNS SNMP interface to set network
parameters.
ŸEmail: Set Emails for sending and receiving alarm messages
and password retrieval message.
ŸPort Mapping: set the ports for remote accessing.
ŸP2P: Add XVR into device list of App by accessing the QR code.
ŸIP Filter: Settings for creating black list or white list.
Ÿ3G/4G: Use 3G/4G modem to plug to XVR provide the network.
ŸPPPoE: Point to point network to access XVR directly.
ŸNetwork Traffic: view the speed of transiting and receiving
data, view the status of LAN.
ŸPlatform Access: Enable to set the parameters of platform
access, so that the XVR can be connected to platform system.
5.6 Live Video
Live video page is displayed after starting the XVR by default, as
shown in figure 5-5.
Figure 5-5 Live video
The XVR also can be accessed in a Web browser. Open a web
browser like Ch rome 45 and enter the IP address of device (The
default IP address is 192.168.0.121) in the address box, and
press . The login page is displayed as shown in figure 7-1.Enter
Web ccessing A
7
Search for “InView Pro4” in App Store or Google Play to
download and install the mobile client. Use the App to scan the QR
code on the back board of XVR, or in P2P settings page in XVR
user interface. Then input the password of the XVR to add the XVR
into the device list of the App. User can manage the device through
mobile client.
5.5 System
System settings contain Information, General, User, Security
Center, Auto Sequence, Logs, Maintenance and Auto Reboot, as
shown in Figure 5-4.
5.4 Network
Network settings contain Network, 802.1X, DDNS, E-mail, Port
Mapping, P2P, IP Filter SNMP, 3G/4G, PPPoE, Network Traffic
and Platform Access, as shown in figure 5-3. Maybe some models
have more functions, please refer to actual products.
Figure 5-3 Network
ŸSensor Setting: Set the sensor parameter of channels’ cameras.
ŸOSD /Privacy Zone/ROI: Set on live video screen.
ŸChannel Type : set the analog channels’ type, user can set
AUTO/AHD/TVI/CVI/IP.
ŸMicrophone: Adjust and set the microphone of channels.
ŸHuman thermometer/ Smart/ Intelligent Tracking: These
functions are used for special function cameras, configure the
parameters of cameras.
ŸAll these settings can be copied to other channels by clicking
Copy button.
5.3 Alarm
Alarm settings contain General, Motion detection, Camera Tamper,
Video loss, Intelligent analysis, Alarm in, Abnormal alarm, Alarm
out, Local Intelligent Analysis, as shown in figure 5-2
Figure 5-2 Alarm
Figure 5-4 System
System
Channel
Rec ord
Alarm
Network
Sy ste m
Network
802.1X
DDNS
Email
Port Mappi ng
P2P
IP Filter
SNMP
P2 P
En ab le P2P
St atus
P2 P ID
Ap p N am e
- I t is avai la ble on App Sto re an d Google Pl ay
In View Pro 4
A0 11 003AFFPXXXX
On line
ŸGeneral: include system, date and time, time zone, DST, sync
camera time.
ŸUser Account: add user , set advance setting(auto login,
password double authentication, boot wizard) and App
Verification(add whitelist to be allowed which are added to App).
ŸSecurity Center: modify the password, pattern unlock, secure
Email, Secure question.
ŸLayout: set new layout to view live videos of channels. Set
CVBS offset.
ŸLogs: shows operating and alarm log, user can export logs if an
USB disk is plugged in.
ŸMaintenance: include shutdown, reboot, exit system, reset,
import configuration, export configuration and update.
ŸAuto Reboot: enable this function to make device restart
periodically.
Ap ply
Ÿ General: Enable or disable alarm and set duration time of alarm.
Ÿ Motion Detection: Enable this function, if detection the motion
actions, it will alarm.
1. Event actions: Contain buzzer, alarm out, push message to
App, pop-up message to monitor, send E-mail and post recording
( after enabling, choose the recording time from drop list.)
2. Area: set motion detection area. Press left button and drag the
cursor to add a detection area, and double-click an area to delete
it.
3. Schedule: Set schedule to enable or disable motion detection
alarm. There are three methods to set, click the double arrows
button to choose all day. The second, click and drag the cursor to
select periods. The third, click one by one.
ŸVideo Loss, Intelligent Analysis are same settings as motion
detection.
ŸAlarm In Alarm Out/ : settings for I/O alarming.
ŸAbnormal Alarm can tick disk error, IP conflict, network
disconnected.
ŸLocal Intelligent Analysis: set up to 4 channels intelligent
analysis alarm. choose the channel and apply, the XVR will
reboot, then set the parameters of intelligent analysis.
System
Ch ann el
Re cord Al arm Netwo rk System
General
Motion Detect ion
Video Loss
Intelligent Analysis
Alarm In
General
En ab le Alarm
Al arm D uration Ti me (sec)
Ap ply
Abnormal Alar m
Alarm Out
5.2 Record
Record settings contain Record Schedule, Disk, Storage, Disk
Calculation, SMART, Disk Detection, Disk Calculation and FTP.
Set record schedule and storage strategic. User can calculate the
disk’s using time at Disk Calculation interface.
Enter S.M.A.R.T interface to view the state of disks.
Disk Detection can detect the disks.
FTP: set the parameters of FTP upload, the alarm video can be
sent to FTP path.
Activation
Ent er channel default pas sword
Confirm t he new password
Enter a new pas sword
Username
Language
-Valid password range [6-32] characters.
-At leas t 2 kinds of number s, lowercas e, uppercas e or special
-Only these special char acter s are support !@ #$*+-=_%&”’
-Channel default pas sword limi t is not empty
OK
InView Pro4
Analog cameras
Router
Remote monitor
Channel
Record
Network
Alarm
System
Camera Encode
Sensor Setting OSD
Privacy Zone Channel Type
Record Schedule
Disk Network
802.1X
Port Mapping
DDNS
Email
P2P
IP Filter
SNMP
General
Motion Detection
Camera Tamper Video Loss
Intelligent Analysis
Information
General
User A ccount
Security Center Auto Sequenc.
Maintenance Auto Reboot
Storage Mode
S.M.A.R.T
Disk Detection
3G/4G . . .
Logs
Alarm In
Abnormal Alarm . . .
Disk Calculation.
ROI
Microphone
Human Thermmnet. . . .
FTP
Camera Tamper
Local Intelligent Analysis
IO Control Push
Bu zz er Duration Time(se c)
10
0
19 2 . 168 . 0 . 1
PPPOE
3G /4G
Al ternate DNS Server
Network Traff ic
Platform Access
In formation
System
Dev ice I D
11_JYE1_00_04
Dev ice Name
Dev ice Type
Dev ice
DVR
Model
0070-10403-A
Firmware Version
V4. 6.0805. 0000.003.0.50. 2.0
HDD Number
Channels Suppor ted
Alarm In
Alarm Out
Audio I n
Audio Out
Ge ne ral
Us er Acc ou nt
Se cu rity Center
La yo ut
Lo gs
Ma in tenance
Au to Reboot
System
Channel
Record
Alarm
Net work
System
U-boot Version
Ker nel Version
2
24
8
1
8
1
15060F1320035
1506017142315
Network
Channel
Disk
Alarm
3G/4G
PPPOE
Network Traffic
Platform Access
IP cameras
Switch/ Router
Especificaciones del producto
| Marca: | Ernitec |
| Categoría: | Videograbadora |
| Modelo: | NVR Hybrid |
¿Necesitas ayuda?
Si necesitas ayuda con Ernitec NVR Hybrid haz una pregunta a continuación y otros usuarios te responderán
Videograbadora Ernitec Manuales
13 Septiembre 2024
13 Septiembre 2024
Videograbadora Manuales
- Videograbadora Sony
- Videograbadora Philips
- Videograbadora Daewoo
- Videograbadora Grundig
- Videograbadora JVC
- Videograbadora Motorola
- Videograbadora Medion
- Videograbadora Toshiba
- Videograbadora Canon
- Videograbadora Aiwa
- Videograbadora Acti
- Videograbadora Hikvision
- Videograbadora Hitachi
- Videograbadora TP Link
- Videograbadora DataVideo
- Videograbadora Axis
- Videograbadora Sylvania
- Videograbadora Digitus
- Videograbadora Dahua Technology
- Videograbadora GeoVision
- Videograbadora QNAP
- Videograbadora Reolink
- Videograbadora UniView
- Videograbadora Planet
- Videograbadora Navitel
- Videograbadora Foscam
- Videograbadora Tenda
- Videograbadora Ubiquiti Networks
- Videograbadora Seagate
- Videograbadora Synology
- Videograbadora Trendnet
- Videograbadora Vivotek
- Videograbadora Provision ISR
- Videograbadora AVer
- Videograbadora Speco Technologies
- Videograbadora Hanwha
- Videograbadora Inkovideo
- Videograbadora Avigilon
- Videograbadora Milesight
Últimos Videograbadora Manuales
26 Octubre 2024
22 Octubre 2024
20 Octubre 2024
15 Octubre 2024
10 Octubre 2024
9 Octubre 2024
8 Octubre 2024
7 Octubre 2024
2 Octubre 2024
24 Septiembre 2024