Extech SDL400 Manual de Usario
Extech
medidor de luz
SDL400
Lee a continuación 📖 el manual en español para Extech SDL400 (5 páginas) en la categoría medidor de luz. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/5
USER GUIDE
Light Meter
SD Card real-time datalogger
Model SDL400
5 SDL400-EU-EN V1.2 9/12
Setup Mode
Basic settings at a glance
To view the current conguration of the meter with regard to time, date, and datalogging sampling
rate press the SET button momentarily. The meter will now display the conguration in quick
succession. If the information is missed on the rst try, simply press the SET button again until all of
the information is noted.
Accessing the Setup mode
1. Press and hold the SET button for at least 1.5 seconds to access the Setup menu.
2. Press the SET button momentarily to step through the available parameters. The parameter
type is shown on the bottom of the LCD and the current selection for that type is shown above
it.
3. When a parameter is displayed that is to be changed, use the arrow keys to change the
setting. Press the ENTER button to conrm a change.
4. Press and hold the SET button for at least 1.5 seconds to exit the Setup mode. Note that the
meter automatically switches out of the Setup mode if no key is pressed within 7 seconds.
5.
The available Setup parameters are listed below. Additional detailed information is provided
below this list:
dAtE
Set the clock (Year/Month/Date; Hours/Minutes/Seconds)
SP-t
Set the datalogger sampling rate (Hours/Minutes/Seconds)
PoFF
Automatic power-off management (Enable or disable the auto-power o function)
bEEP
Set the beeper sound ON/OFF
dEC
Set the numerical format; USA (decimal: 20.00) or European (comma: 20,00)
Sd F
Format the SD memory card
t-CF
Units of measure selection for temperature readings (C or F)
tYPE
Select the Thermocouple type (K or J)
Setting the Clock Time
1. Access the dAtE parameter as described in the Accessing Setup Mode section above.
2. Use the arrow keys to change a value.
3. Use the ENTER button to step through the selections.
4. Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode (or
simply wait 7 seconds for the meter to automatically switch to the normal operating mode).
5. The clock will keep accurate time even when the meter is switched o. However, if the battery
expires the clock will have to be reset after fresh batteries are installed.
Setting the Datalogger Sampling Time (Rate)
1. Access the SP-t parameter as described in the Accessing Setup Mode section above.
2. The sampling rate can be set to ‘0’ seconds (for manual logging) or
1, 2, 5, 10, 30, 60, 120,
300, 600, 1800, 3600 seconds for auto logging.
Use the arrow keys to select the sampling rate.
3.
Press the ENTER button to confirm the entry.
4. Press and hold the SET button for at least 1.5 seconds to exit to the normal operation mode (or
simply wait 7 seconds for the meter to automatically switch to the normal operating mode).
8 SDL400-EU-EN V1.2 9/12
Datalogging and PC Interface
Types of Data Recording
• Manual Datalogging: Manually log up to 99 readings onto an SD card via push-button press.
• Automatic Datalogging: Automatically log data onto an SD memory card where the number of
data points is virtually limited only by the card size. Readings are logged at a rate specied by
the user.
SD Card Information
• Insert an SD card (from 1G size up to 16G) into the SD card slot at the bottom of the meter. The
card must be inserted with the front of the card (label side) facing toward the rear of the meter.
• If the SD card is being used for the rst time it is recommended that the card be formatted and
the logger’s clock set to allow for accurate date/time stamping during datalogging sessions.
Refer to the Setup Mode section for SD card formatting and time/date setting instructions.
• European and USA numerical formats dier. The data on the SD card can be formatted for
either format. The meter defaults to USA mode where a decimal point is used to separate units
from tenths, i.e. . The European format uses a comma, i.e. 20.00 20,00. To change this setting,
refer to the Setup Mode section.
Manual Datalogging
In the manual mode the user presses the LOG button to manually log a reading onto the SD card.
1. Set the sampling rate to ‘0’ seconds as described in the Setup Mode section.
2. Press and hold the LOG button for at least 1.5 seconds and the lower portion of the display will
show P- ( = memory position number 1-99). n n
3. Momentarily press the LOG button to store a reading. The REC icon will ash each time a data
point is stored.
4. Use the and ▲ ▼ buttons to select one of the 99 data memory positions in which to record.
5. To exit the manual datalogging mode, press and hold the LOG button for at least 1.5 seconds.
The P icon will switch o. n
Especificaciones del producto
| Marca: | Extech |
| Categoría: | medidor de luz |
| Modelo: | SDL400 |
¿Necesitas ayuda?
Si necesitas ayuda con Extech SDL400 haz una pregunta a continuación y otros usuarios te responderán
medidor de luz Extech Manuales
31 Julio 2024
medidor de luz Manuales
- medidor de luz Pyle
- medidor de luz Voltcraft
- medidor de luz Kyoritsu
- medidor de luz Gossen
- medidor de luz Sekonic
- medidor de luz Uni-T
Últimos medidor de luz Manuales
2 Octubre 2024
2 Octubre 2024
2 Octubre 2024
14 Septiembre 2024
13 Septiembre 2024
13 Septiembre 2024
13 Septiembre 2024
10 Septiembre 2024
10 Septiembre 2024
3 Septiembre 2024