Fibaro Roller Shutter FGRM-222 Manual de Usario

Fibaro No categorizado Roller Shutter FGRM-222

Lee a continuación 📖 el manual en español para Fibaro Roller Shutter FGRM-222 (2 páginas) en la categoría No categorizado. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

ENG

Fibaro Roller Shutter is a universal, Z-Wave compatible, electric

motor controller. The device allows for controlling motors of roller

blinds, awnings, venetian blinds, gates and others, which are single

phase AC powered. Fibaro Roller Shutter allows for precise

positioning of a roller blind or venetian blind lamellas. Precise

positioning is available for the motors equipped with mechanic and

electronic end switches.

The module may be controlled wirelessly, through the Z-Wave

network main controller, or through the switch keys connected to it.

It’s also possible to combine few devices into groups of devices,

which then can be controlled simultaneously. In addition, Fibaro

Roller Shutter is equipped with Power Metering.

SPECIFICATIONS

Power Supply

Supplied motor type

Supported limit switches type

Power of supplied motor

In accordance

with EU standards

Circuit Temperature limit

Operational Temperature

For installation in boxes

Radio protocol

Radio Frequency

Radio signal power

Range

Dimensions (L x W x H)

Electricity consumption

110 - 230 V ±10% 50/60Hz

Single phase, VAC

Electronic and mechanic

up to 1kW for 230V

up to 500W for 110V

LVD (2006/95/EC)

EMC (2004/10B/EC)

R&TTE(1999/5/EC)

105 °C

0 - 40 °C

Ø ≥ 50mm

Z-Wave

868,4 MHz EU;

908,4 MHz US;

921,4 MHz ANZ;

869,2 MHz RU;

1mW

up to 100m outdoors

up to 30m indoors

(depending on building materials

used)

42 x 37 x 17 mm

< 0,8W

TECHNICAL INFORMATION

• Controlled by Fibaro System devices or any Z-Wave controller

• Microprocessor control

• Executive elements: relays

• The device may be operated by momentary or toggle switches,

and by dedicated roller blind control switches

• Connected motor’s current and historical power consumption

measured

WARNING

Danger of electrocution! Any work on the device

regarding electrical connections may be performed

only after the power supply has been

disconnected.

OPERATING MANUAL

FIBARO ROLLER SHUTTER

FGRM-222-EN-A-v1.00

I. GENERAL INFORMATION ABOUT FIBARO SYSTEM

Fibaro is a wireless system, based on Z-Wave technology. Fibaro

provides many advantages when compared to similar systems. In

general, radio systems create a direct connection between the

receiver and transmitter. However, a radio signal is weakened by

various obstacles located in its path (apartment walls, furniture,

etc.) and in extreme cases it fails to transfer required data. The

advantage of Fibaro System is that its devices, apart from being

transmitters and signal receivers, also duplicate signal. When a

direct connection path between the transmitter and the receiver

cannot be established, the connection may be achieved through

other intermediate devices.

Fibaro is a bi-directional wireless system. This means that the

signal is not only sent to the receivers but also the receivers send

the confirmation of its reception. This operation confirms their

status, which checks whether they are active or not. Safety of the

Fibaro System transmission is comparable to the safety of

transmission in data bus wired systems.

Fibaro operates in the free bandwidth for data transmission. The

frequency depends on radio regulations in individual countries.

Each Fibaro network has its own unique network identification

number (home ID), which is why it is possible to co-operate two or

more independent systems in a single building without any

interference.

Although Z-Wave is quite a new technology, it has already become

recognized and officially a binding standard, similarly to Wi-Fi.

Many manufacturers in various industries offer solutions based on

Z-Wave technology, guaranteeing their compatibility. This means

that the system is open and it may be extended in the future. Find

more information at www.fibaro.com.

Fibaro generates a dynamic network structure. After Fibaro System

is switched on, the location of its individual components is

automatically updated in real-time through status confirmation

signals received from devices operating in a "mesh" network.

II. ROLLER SHUTTER INSTALLATION

1. Before installation make sure the voltage supply is

disconnected.

2. Connect the Roller Shutter in accordance with the wiring

diagram presented on Fig. 1 (roller blinds, venetian blinds) or

Fig. 2 (gates).

3. Place the device in a switch box.

4. Arrange the antenna (tips presented below Fig.2)

5. Turn on the power supply keeping the necessary safety

precautions.

6. Include the module into the Z-Wave network, observing pt. III

description.

7. If necessary, calibrate the module, observing pt. VI descripion.

NOTES FOR THE DIAGRAM:

L - terminal for live lead

N - terminal for neutral lead

S1 - terminal for key no. 1 (has the option of entering the device in

learning mode)

S2 - terminal for key No. 2

O1 - output terminal no. 1 for shutter motor

O2 - output terminal no. 2 for shutter motor

B - service button (used to add or remove a device from the

system)

ROLLER BLIND POSITIONING CALIBRATION

TIPS FOR ARRANGING THE ANTENNA

1. Locate the antenna as far from metal elements as possible

(connection wires, bracket rings, etc.) in order to prevent

interferences.

2. Metal surfaces in direct vicinity of the antenna (e.g. metal switch

boxes, door frames) may impair radio signal reception!

3. Do not cut or shorten the antenna. Its length is perfectly

matched to the band in which the system operates.

NOTE

A push button connected to S1 terminal operates

the O1 output, while the push button connected to

S2 terminal operates the O2 output. It’s recommen-

ded to connect an UP button to S1 terminal and a

wire, responsible of up movement, to O1 output

terminal. Respectively, a DOWN button should be

connected to S2 terminal and a wire, responsible

for down movement, to O2 output terminal.

WARNING

Fibaro Roller Shutter is dedicated to operate with

AC powered electric motors. Connecting the device

directly to DC powered motors may result in them

being damaged.

Fig. 3 Roller Shutter icons in Home Center interface

WARNING

Danger of electrocution! Even when the device is

turned off, voltage may be present at it’s terminals.

Any work on the device regarding electrical

connections may be performed only after the

power supply has been disconnected.

WARNING

Any maintenance work on controlled devices may

be performed only after the power supply has been

disconnected.

WARNING

It’s not recommended to operate all of the roller

blinds simultaneously. For safety reasons, at least

one roller blind should be controlled independently,

providing safe escape route in case of emergency.

WARNING

Do not connect the device to loads exceeding

recommended value.

Fig. 1 Roller Shutter wiring diagram

III. Z-WAVE NETWORK INCLUSION

Fibaro Roller Shutter may be included into the Z-Wave network via

the B-button or a push button connected to the S1 terminal. In

addition, the module may be included in auto inclusion mode, by

simply connecting the power supply.

Automatic Z-Wave network inclusion:

1) Make sure the power supply is disconnected and a Roller Shutter

is located within a direct Z-Wave network’s main controller

communication range.

2) Set the main controller into the learn mode (see main controllers

operating manual).

3) Connect the power supply to include the Roller Shutter in auto

inclusion mode.

4) Fibaro Roller Shutter will be automatically detected and included

into the Z-Wave network.

To disable the auto inclusion mode, press the B-button briefly, after

connecting the module to the power supply.

Manual Z-Wave network inclusion:

1) Connect the power supply.

2) Set the main controller into the learn mode (see main controllers

operating manual).

3) Triple click the B-button or a push button connected to the S1

terminal.

4) Fibaro Roller Shutter will be detected and included into the

Z-Wave network.

IV. Z-WAVE NETWORK EXCLUSION

Excluding Fibaro Roller Shutter from the Z-Wave network:

1) Make sure the module is connected to the power supply.

2) Set the main controller into the learn mode (see main controllers

operating manual).

3) Triple click the B-button or a push button connected to the S1

terminal.

V. ROLLER SHUTTER RESET

Reset procedure clears the modules’ EPROM memory, including all

information about the Z-Wave network controller, calibration and

power consumption data.

1) Make sure the module is connected to the power supply.

2) Press and hold the B-button for ca. 14 seconds.

3) LED indicator will glow yellow.

4) Release the B-button and press it again, briefly.

5) The Roller Shutter memory is now empty.

6) The module goes into the auto inclusion mode, until any button

is pushed.

NOTE

Memory reset does not remove the module from

the Z-Wave network main controller’s memory.

Prior to memory reset it’s recommended to exclude

the module from the Z-Wave network.

TIP

After memory reset, the Roller Shutter goes into the

auto inclusion mode and waits to be included into

the Z-Wave network. To exit the auto inclusion

mode press the B-button briefly.

Fig. 2 Connecting Roller Shutter to GATE motor

VI. POSITIONING CALIBRATION

Calibration is a process during which a Roller Shutter learns the

position of the limit switches and a motor characteristic. Calibration

is mandatory in order for the Roller Shutter to correctly recognize a

roller blind position. The procedure consists of an automatic, full

movement between the limit switches (up, down, and up again).

There are separate procedures of calibrating roller blind and

lamellas (venetian blind) positioning. Each time the calibration

requires the completion of a full cycle (up and down).

There are 5 procedures of calibrating a Fibaro Roller Shutter to

choose from. Each one gives the same results and the user may

choose which one to execute.

A. Calibration through a Fibaro Home Center 2 interface

1) Make sure the module is connected to the power supply,

according to Fig.1

2) Include the module into the Z-Wave network, according to

section

III of instructions.

3) In Home Center 2 interface choose Fibaro Roller Shutter’s

advanced settings.

4) Click CALIBRATE buttin in the devices advanced settings tab.

5) Roller Shutter performs the calibration process, completing full

cycle - up, down and up again.

6) Using an interface test whether the positioning works correctly.

B. Calibration through the Z-Wave network

1) Make sure the module is connected to the power supply,

according to Fig.1

2) Include the module into the Z-Wave network, according to pt.III

instructions.

3) Set the parameter 29 value to 1.

4) Roller Shutter performs the calibration process, completing full

cycle - up, down and up again.

5) The parameter 29 value will be automatically set to 0.

6) Using an interface test whether the positioning works correctly.

C. Calibration through the switch keys

1) Make sure the module is connected to the power supply,

according to Fig.1, and to the switch keys as well (S1 and S2

inputs).

2) Include the module into the Z-Wave network, according to

section

III of instructions.

3) Press and hold the switch key connected to S1 or S2 input

terminal and release it after at least 3 seconds.

4) Press and hold the same switch key again, and release it after 3

seconds.

5) Now press and hold the same button, for 3 seconds, for the 3rd

time.

6) After pressing and releasing the button for the third time,

automatic calibration sequence will start.

7) Roller Shutter performs the calibration process, completing full

cycle - up, down and up again.

D. Calibration through Menu (B-button)

1) Make sure the module is connected to the power supply,

according to Fig.1

2) Include the module into the Z-Wave network, according to

section

III of instructions.

3) Press and hold the B-button for ca. 6 seconds.

4) LED will glow blue.

5) Release the B-button and press it again, briefly.

6) Roller Shutter performs the calibration process, completing full

cycle - up, down and up again.

CALIBRATING LAMELLAS POSITIONING

IN VENETIAN BLINDS

Apart from calibrating the roller blind position, it’s possible to

calibrate the position of venetian blinds lamellas. After correct

calibration, in case of venetian blinds, it’s possible to set the position

between the limit switches, as well as the lamellas angle. By default,

time of full turn of the lamellas is set to 1,5 seconds. If necessary, it

can be modified following below instructions.

1) Make sure the module is connected to the power supply,

according to Fig.1

2) Include the module into the Z-Wave network, according to section

III of instructions.

3) Calibrate the Roller Shutter, according to the instructions

provided in sections VI.A, VI.B, VI.C, VI.D or VI.E.

4) Set the parameter 10 value to 2 or choose in HC2 interface:

Device Type - Venetian Blind

5) Another device icon, responsible for lamellas operation, will show

up in Home Center 2 interface. In case of any other Z-Wave

network controllers managing the lamellas position is achieved

through pressing and holding a switch key (up or down).

6) By default, time of transition between extreme positions is set to

1 500 ms (1,5 seconds).

7) Turn lamellas between extreme positions. If after full cycle a blind

starts moving up or down, then parameter’s 12 value must be

modified, e.g. to 1 000ms (1 second). Correctly configured

lamellas should not force the blind to move up or down.

NOTE

Roller Shutter needs to be calibrated to work with

any given motor.

NOTE

In Venatian Blind mode, lamellas need to be

calibrated to work with any given motor.

VII. OPERATING THROUGH THE Z-WAVE NETWORK

After including into the Z-Wave network, Fibaro Roller Shutter will

be presented in a Home Center 2 interface as a roller blind icon (see

fig. below). After choosing Venetian Blind device type, a second icon

will show up, responsible for managing lamellas position.

User can choose from the following operating modes:

1. Roller Blind Mode, without positioning

2. Roller Blind Mode, with positioning

3. Venetian Blind Mode

4. Gate Mode, without positioning

5. Gate Mode, with positioning

After choosing one of the above operating modes, device will be

represented in Home Center 2 interface by icons shown in Fig.4. In

addition, each operating mode affects certain parameters settings:

1) Roller blind without positioning (parameter 10 set to 0)

2) Roller blind with positioning (parameter 10 set to 1)

3) Venetian blind (parameter 10 set to 2; parameter 13, set to 2)

4) Gate without positioning (parameter 10 set to 3; parameter 12 set

to 0; parameter 17 set to 0)

5) Gate with positioning (parameter 10 set to 4; parameter 12 set to

0; parameter 17 set to 0)

Opening / Closing a blind is acheved through moving a slider or

pushing a button shown in fig. 3.

In Venetian Blind mode, setting lamellas angle is achieved through

moving a slider or pushing a button shown in fig. 3.

VIII. MANUAL OPERATION

Fibaro Roller Shutter allows for connecting push buttons to S1 and

S2 terminals. These may be momentary or toggle switches,

alternatively. Push buttons are responsible for managing the blind’s

movement.

Using momentary switches:

Clicking button connected to S1 terminal, initiates up

movement.

Clicking button connected to S2 terminal, initiates down

movement.

If the blind is moving, each click, of any button, will stop the

movement. In addition a button click sends a command frame to I-st

association group devices.

In case of venetian blinds, it’s possible to manage the lamellas

angle. Operating Mode - Venetian Blind, or Parameter 10 value set

to 2.

Holding connected to S1 terminal initiates lamellas rotation up.

Holding connected to S2 terminal initiates lamellas rotation

down.

In addition a button hold sends a Fibar Command Class control

frame to II-nd association group devices.

IX. ASSOCIATIONS

Through an association Fibaro Roller Shutter may control another

Z-Wave network device, e.g. another Roller Shutter, Wall Plug,

Dimmer, Relay Switch, RGBW Controller.

NOTE

Association allows for direct communication

between Z-Wave network devices. Main controller

does not take part in such communication.

Fibaro Roller Shutter provides three association groups:

I association group is triggered through a momentary switch click,

or a toggle switch position change.

II association group is triggered through a momentary switch hold

NOTE

II association group is inactive when toggle

switches are used or in Gate Controller mode

(parameter 10). In case of controlling Venetian

Blinds, control commands are sent in Fibar

Command Class standard.

III association group reports the module status. Only one device

may be assigned to this group, main controller by default. It’s not

recommended to modify this group’s settings.

Fibaro Roller Shutter allows for commanding other Roller Shutters,

associated into I or II association group, through clicking or holding

a switch key. For example, this mechanism allows for operating a

Roller Shutter connected to the switch with a button click, and

operating the devices associated in II association group by a button

hold. In addition, when operating Venetian Blinds, it’s possible to

synchronize many devices.

USING ASSOCIATIONS TO OPERATE ANOTHER

ROLLER SHUTTER OR ANY OTHER Z-WAVE

DEVICE.

I ASSOCIATION GROUP:

Clicking button, connected to S1 terminal will initiate up

movement in associated Roller Shutters, or send Turn On command

frame to the devices associated in I-st association group.

Clicking button, connected to S2 terminal will initiate down

movement in associated Roller Shutters, or send Turn Off command

frame to the devices associated in I-st association group.

II ASSOCIATION GROUP:

Holding button , connected to S1 terminal will move the

connected roller blind up, and after 1 second delay initiate up

movement in associated Roller Shutters, or send Turn On command

frame to the devices associated in II-nd association group.

Holding button, connected to S2 terminal will move the

conected rolled blind down, and after 1 second delay initiate down

movement in associated Roller Shutters, or send Turn Off command

frame to the devices associated in II-nd association group.

NOTE

To abort the calibration process press any key

(connected to S1 or S2) or send a STOP control

frame through the Z-Wave network controller. In

Gate Controller mode the calibration process will

be aborted after disconnecting the S2 terminal.

Using toggle switches:

Changing switch key position, connected to S1 terminal,

initiates up movement.

Changing switch key position, connected to S2 terminal,

initiates down movement.

Choosing a middle position stops the blind.

NOTE

Venetian blind lamellas may be only operated by

momentary switches.

NOTE

Above operating modes and their default settings

are modified automatically only in Home Center 2

controller. In case of the Z-Wave network

controllers from other manufacturers, these

settings need to be manually adjusted (see section

XV).

L NS1 S2

O2 O1

safety switch

sensor

Fibaro Roller

Shutter

limit

switches

E. Calibration through a Fibar Command Class control frame.

It’s possible to force the calibration process execution through

sending a Fibar Command Class control frame through a Z-Wave

network main controller (see a Fibar Command Class documenta-

tion).

WARNING

It is recomended to monitor regulary operation of

Fibaro Roller shutter in all modes. In case of gate

control mode device, motor limit switches, infrared

barriers and emergency stop should be monitored

and maintained regulary

USING ASSOCIATIONS TO OPERATE ROLLER

SHUTTERS CONNECTED TO VENETIAN BLINDS.

Using association mechanism to operating venetian blinds requires

configuring both, I-st and II-nd association groups.

I ASSOCIATION GROUP

Clicking button, connected to S1 terminal will initiate up

movement of the connected venetian blind and other devices

associated in I-st association group.

Fibaro Roller

Shutter

L NS1 S2

Clicking button, connected to S2 terminal will initiate down

movement of the connected venetian blind and other devices

associated in I-st association group.

II ASSOCIATION GROUP (relevant for momentary switches only)

Holding button, connected to S1 terminal will initiate lamellas

rotation up, of the connected venetian blind as well as the other

devices associated in II-nd association group.

Holding button, connected to S2 terminal will initiate lamellas

rotation down, of the connected venetian blind as well as the other

devices associated in II-nd association group.

NOTE

Once the associated devices are already moving,

they will be stopped if any of the buttons is pressed

and held.

NOTE

In Gate Mode, by default, the S1 terminal is set to

operate with a momentary switch, ignoring the

parameter 14 settings.

Full opening the gate initiates a Roller Shutter COUNTDOWN.

After the COUNTDOWN the gate will start closing. COUNTDOWN

length is set through the parameter 12. In addition, if the IR barrier

is cut (S2 contact opened) at the gate fully open, the gate will start

closing after a time period specified in parameter 17.

NOTE

In both Gate Modes, with and without positioning,

parameters 12 and 17 are automatically set to 0. At

these settings the gate will open, but will not

automatically close. Relevant times need to be set

manually in parameters 12 and 17 (see section

XV).

XI. LED INDICATOR

Fibaro Roller Shutter has a MENU. Each MENU level is signaled

through a LED Indicator colour. To enter MENU press and hold the

B-button for at least 2 seconds.

While the B-button is being held, LED Indicator colours will change

in the following sequence:

XII. Z-WAVE RANGE TESTER

Fibaro Roller Shutter has a built in mechanism, allowing to roughly

estimate the Z-Wave network range.

NOTE

To allow for the Z-Wave network range test, the

Z-Wave network controller needs to support the

functionality and the module needs to be included

in the network. Z-Wave range test puts heavy strain

on the network, so it’s recommended to use the

function only in special cases.

In order to test the Z-Wave network range:

1) Press and hold the B-button for ca. 6 seconds, until the LED

Indicator glows violet.

2) Release the B-button.

3) Click the B-button.

4) LED Indicator will signal the Z-Wave network range (see

description below).

5) Click the B-button to exit the Range Tester.

Network range signaling modes:

Z-Wave network range is signaled by LED illumination colour and

behaviour. Blinking each 1-second means the modules tries to

establish a direct communication with the main controller, while 2

seconds glowing means the test result. The test is performed in a

loop, until being stopped by the user. Z-Wave range test is

performed in three steps, signaled with green, yellow, violet and

red:

1) Blinking in GREEN means the module tries to establish a direct

communication with the main controller. Positive test result is

signaled by a 2 second glowing in GREEN, after which the test is

repeated (step 1). In practice, if the module is able to establish a

direct communication with the main controller, the LED will glow

GREEN, without blinking.

2) If the module is not able to establish a direct connection with the

main controller, it will try to establish a routed connection, through

another, intermediary, Z-Wave network devices. LED indicator will

change the illumination colour to RED. Positive test result is

signaled with glowing in YELLOW. After 2 seconds the module will

retry establishing a direct communication (step 1).

NOTE

The module may modify the main controller

communication from direct to routed and vice

versa, especially if it’s located at the direct

communication range limit.

3) If the module is not able to establish a routed connection with the

main controller, LED Indicator colour will change from YELLOW to

VIOLET. After few seconds test will end and the LED Indicator will

glow RED for two seconds. Whole procedure will start again and

the module will try to establish a direct connection with the main

controller (step 1).

XIII. CURRENT AND HISTORICAL

POWER CONSUMPTION MEASURING

Fibaro Roller Shutter allows for the current load and power

consumption monitoring. Data is sent to the main controller, e.g.

Home Center 2.

Measuring is carried out by an independent microprocessor

dedicated exclusively for the purpose, assuring maximum accuracy

and precision. The microprocessor is factory calibrated.

Electric power - power consumed by an electric device in an

instant, in Watts (W).

Electric energy - energy consumed by a device through a time

period. Most commonly measured in kilowatt-hours (kWh). One

kilowatt-hour is equal to one kilowatt of power consumed over a

period of one hour, 1kWh = 1000 Wh.

RESETTING ELECTRICITY CONSUMPTION MEMORY

Fibaro Roller Shutters electricity consumption memory may be

cleared in one of the following ways:

1) Through the module reset (see pt. )

2) Through the main controller menu (see main controllers

operating manual

3) Manually using the following instructions:

a) Make sure the device is connected to voltage supply.

b) Press and hold the B-button for ca. 10 seconds, until LED I

ndicator glows GREEN.

c) Release the B-button.

d) Click the B-button.

e) Energy consumption memory has been erased.

NOTE

1) Please contact your local supplier for the current

rates

2) Fibaro Roller Shutter stores consumed electricity

data on its memory, which means disconnecting

the module from voltage supply does not erase the

data.

XIV. PROTECTION MODE

Fibaro Roller Shutter uses the Protection Command Class v2 to

prevent from unintended motor movement. 22.22 software version

supports the following operation modes (following the Z-Wave

protocol description).

1) Local Protection

Local Protection State:

0 - no protection. Roller Shutter responds to push buttons.

1 - not supported

2 - Local protection active. Roller Shutter does not respond to

push buttons.

Once the Local Protection is activated, the module stops

responding to S1 and S2 push buttons. SCENE ID and association

commands will not be sent as well. The only exception is the

B-button. Menu and Z-Wave network inclusion, after the B-button

or S1 push button triple click, are still active.

NOTE

There’s one more exception in Local Protection. In

Gate Mode, S2 (IR Barrier) is still active. It means if

the obstacle is detected, the gate will stop,

regardless the Local Protection State set.

2) RF Protection (radio protection)

RF Protection State:

0 – No protection. Roller Shutter responds to command frames.

1 - RF Protection active. Roller Shutter does not respond to the

Z-Wave control frames.

2 - not supported.

Once the RF Protection is activated, the module stops responding

to command frames setting the blind position. It’s still possible

however to configure the device (advanced configuration

parameters, protection modes) and checking it’s current state

through polling (position, power, energy).

XV. ADVANCED CONFIGURATION

GENERAL SETTINGS:

3. Reports type

0 – Blind position reports sent to the main controller using Z-Wave

Command Class.

1 - Blind position reports sent to the main controller using Fibar

Command Class.

Parameters value shoud be set to 1 if the module operates in

Venetian Blind mode.

Defauld setting: 0

Parameter size: 1 [byte]

NOTE

To make sure whether Fibar Command Class is

supported by Z-Wave network main controllers

from other manufacturers, please contact the

controllers manufacturer.

10. Roller Shutter operating modes:

0 - Roller Blind Mode, without positioning

1 - Roller Blind Mode, with positioning

2 - Venetian Blind Mode, with positioning

3 - Gate Mode, without positioning

4 - Gate Mode, with positioning

Default settng: 1

Parameter size: [byte]1

12. In Venetian Blind mode (parameter 10 set to 2) the

parameter determines time of full turn of the lamellas.

In Gate Mode (parameter 10 set to 3 or 4) the parameter defines

the COUNTDOWN time, i.e. the time period after which an open

gate starts closing. In any other operating mode the parameter

value is irrelevant.

Value of 0 means the gate will not close automatically.

Available settings: (0 - 655,35s) 0-65535

Default setting: (1,5 s)150

Parameter size: 2 [bytes]

13. Set lamellas back to previous position.

In Venetian Blind Mode (parameter 10 set to 2) the parameter

influences lamellas positioning in various situations. In any other

operating mode the parameter value is irrelevant.

0 - Lamellas return to previously set position only in case of the

main controller operation.

1 - Lamellas return to previously set position in case of the main

controller operation, momentary switch operation, or when the

limit switch is reached.

2 - Lamellas return to previously set position in case of the main

controller operation, momentary switch operation, when the limit

switch is reached or after receiving a “STOP” control frame

(Switch Multilevel Stop).

Default setting: 1

Parameter size: 1 [byte]

14. Switch type.

The parameter settings are relevant for Roller Blind Mode and

Venetian Blind Mode (parameter 10 set to 0, 1, 2).

0 - Momentary switches

1 - Toggle switches

2 - Single, momentary switch. (The switch should be connected to

S1 terminal)

Default setting: 0

Parameter size: 1 [byte]

17. In Roller Blind Mode or Venetian Blind mode (parameter 10

set to 0, 1, 2) the parameter determines when the Roller

Shutter relays are turned off after reaching a limit switch.

In Gate Mode (parameter 10 set to 3 or 4) the parameter

determines a time period after which a gate will start closing after a

S2 contact has been disconnected. In this mode, time to turn off the

Roller Shutter relays after reaching a limit switch is set to 3 seconds

and cannot be modified.

Value of 0 means the gate will note close automatically.

Available settings: (0,1-25,5s).0 - 255

Default setting: (1s).10

Parameter size: 1 [byte]

18. Motor operation detection.

Power threshold to be interpreted as reaching a limit switch.

Available settings: (1-255 W)0 - 255

The value of 0 means reaching a limit switch will not be detected

Default setting: (10W).10

Parameter size: 1 [byte]

22. Motor operation time.

Time period for the motor to continue operation.

Available settings: (0 – 65535s)0 – 65535

The value of 0 means the function is disabled.

Default setting: (240s. – 4 minutes)240

Parameter size: 2 [bytes]

29. Forced Roller Shutter calibration.

By modifying the parameters setting from 0 to 1 a Roller Shutter

enters the calibration mode. The parameter relevant only if a Roller

Shutter is set to work in positioning mode (parameter 10 set to 1, 2

or 4).

1 - Start calibration process

Default setting: 0

Parameter size: 1 [byte]

ALARM SETTINGS:

30. Response to general alarm

0 - No reaction.

1 - Open blind.

2 - Close blind.

Default setting: 2

Parameter size: 1 [byte]

31. Response to flooding alarm

0 - No reaction.

1 - Open blind.

2 - Close blind.

Default setting: 0

Parameter size: 1 [byte]

32. Response to smoke, CO or CO2 alarm

0 - No reaction.

1 - Open blind.

2 - Close blind.

Default setting: 1

Parameter size: 1 [byte]

33. Response to temperature alarm

0 - No reaction.

1 - Open blind.

2 - Close blind.

Default setting: 1

Parameter size: 1 [byte]

35. Managing lamellas in response to alarm.

In Venetian Blind Mode (parameter 10 set to 2), the parameter

determines how the lamellas will react upon alarm detection. In any

other modes, the parameter value is not relevant.

0 - Do not change lamellas position - lamellas return to the last set

position.

1 - Set lamellas to their extreme position.

Default setting: 1

Parameter size: 1 [byte]

POWER AND ENERGY REPORTS SETTINGS:

40. Power reports.

Power level change that will result in new power value report being

sent. The parameter defines a change that needs to occur in order

to trigger the report. The value is a percentage of the previous

report.

Power report threshold available settings: (1-100%). 1-100

Value of 0 means the reports are turned off.

Default setting: (10%).10

Parameter size: 1 [byte]

42. Periodic power or energy reports.

The parameter defines a time period between consecutive reports.

Available settings: (1-65534 seconds)1-65534

Value of means the reports are turned off.0

Default setting: (3600 seconds / 60 minutes).3600

Parameter size: 2 [bytes]

43. Energy reports.

Energy level change which will result in new energy value report

being sent. The parameter defines a change that needs to occur in

order to trigger the report.

Energy threshold available settings: (0,01 - 2,54kWh).1-254

Value of means the reports are turned off.0

Default setting (0,1kWh).10

Parameter size: 1 [byte]

44. Self-measurement.

A Roller Shutter may include power and energy used by itself in

reports sent to the main controller.

0 - Self-measurement inactive.

1 - Self-measurement active.

IX. OPERATING GATE MOTORS

Fibaro Roller Shutter allows for operating gate motors. Gate motor

should be connected to O1 and O2 terminals according to Fig.2. In

the Gate Mode, a momentary switch may be connected to S1

terminal. It’s recommended to connect an IR barrier, an emergency

stop button or any alarm mechanism to S2 terminal. Opening a

contact in a device connected to S2 terminal will always result in

stopping a motor in current position (see Fig. 2).

Clicking a push button connected to S1 terminal will initiate opening

the gate. Next click of a button will stop the gate. Yet another click of

a button will close the gate. According to following seaquence:

OPEN → STOP → CLOSE → STOP → OPEN.

1. The Guarantee is provided by FIBAR GROUP Sp. z o.o.

(hereinafter "Manufacturer"), based in Poznan, ul. Lotnicza 1; 60-421

Poznan, entered in the register of the National Court Register kept

by the District Court in Poznań, VIII Economic Department of the

National Court Register, no. 370151, NIP 7811858097, REGON:

301595664.

2. The Manufacturer is responsible for equipment malfunction

resulting from physical defects (manufacturing or material) of the

Device for 12 months from the date of its purchasing.

3. During the Guarantee period, the Manufacturer shall remove any

defects, free of charge, by repairing or replacing (at the sole

discretion of the Manufacturer) any defective components of the

Device with new or regenerated components, that are free of

defects. When the repair impossible, the Manufacturer reserves the

right to replace the device with a new or regenerated one, which shall

be free of any defects and its condition shall not be worse than the

original device owned by the Customer.

4. In special cases, when the device cannot be replaced with the

device of the same type (e.g. the device is no longer available in the

commercial offer), the Manufacturer may replace it with a different

device having technical parameters similar to the faulty one. Such

activity shall be considered as fulfilling the obligations of the

Manufacturer. The Manufacturer shall not refund money paid for the

device.

5. The holder of a valid guarantee shall submit a guarantee claim

through the guarantee service. Remember: before you submit a

guarantee claim, contact our technical support using telephone or

e-mail. More than 50% of operational problems is resolved remotely,

saving time and money spent to initiating guarantee procedure. If

remote support is insufficient, the Customer shall fill the guarantee

claim form (using our website - www.fibargroup.com) in order to

obtain claim authorization.

When the guarantee claim form is submitted correctly, the Customer

shall receive the claim confirmation with an unique number (Return

Merchandise Authorization -RMA).

6. The claim may be also submitted by telephone. In this case, the

call is recorded and the Customer shall be informed about it by a

consultant before submitting the claim. Immediately after submitting

the claim, the consultant shall provide the Customer with the claim

number (RMA-number).

7. When the guarantee claim form is submitted correctly, a

representative of the Authorised Guarantee Service (hereinafter as

"AGS") shall contact the Customer.

8. Defects revealed within the guarantee period shall be removed

not later than 30 days from the date of delivering the Device to AGS.

The guarantee period shall be extended by the time in which the

Device was kept by AGS.

9. The faulty device shall be provided by the Customer with complete

standard equipment and documents proving its purchase.

10. Parts replaced under the guarantee are the property of the

Manufacturer. The guarantee for all parts replaced in the guarantee

process shall be equal to the guarantee period of the original device.

The guarantee period of the replaced part shall not be extended.

11. Costs of delivering the faulty device shall be borne by the

Customer. For unjustified service calls, the Service may charge the

Customer with travel expenses and handling costs related to the

case.

12. AGS shall not accept a complaint claim only when:

• the Device was misused or the manual was not observed,

• the Device was provided by the Customer incomplete, without

accessories or nameplate,

• it was determined that the fault was caused by other reasons than

a material or manufacturing defect of the Device

• the guarantee document is not valid or there is no proof of

purchase,

13. The Manufacturer shall not be liable for damages to property

caused by defective device. The Manufacturer shall not be liable for

indirect, incidental, special, consequential or punitive damages, or

for any damages, including, inter alia, loss of profits, savings, data,

loss of benefits, claims by third parties and any property damage or

personal injuries arising from or related to the use of the Device.

14. The guarantee shall not cover:

• mechanical damages (cracks, fractures, cuts, abrasions, physical

deformations caused by impact, falling or dropping the device or

other object, improper use or not observing the operating manual);

• damages resulting from external causes, e.g.: flood, storm, fire,

lightning, natural disasters, earthquakes, war, civil disturbance, force

majeure, unforeseen accidents, theft, water damage, liquid leakage,

battery spill, weather conditions, sunlight, sand, moisture, high or low

temperature, air pollution;

• damages caused by malfunctioning software, attack of a computer

virus, or by failure to update the software as recommended by the

Manufacturer;

• damages resulting from: surges in the power and/or telecommuni-

cation network, improper connection to the grid in a manner

inconsistent with the operating manual, or from connecting other

devices not recommended by the Manufacturer.

• damages caused by operating or storing the device in extremely

adverse conditions, i.e. high humidity, dust, too low (freezing) or too

high ambient temperature. Detailed permissible conditions for

operating the Device are defined in the operating manual;

• damages caused by using accessories not recommended by the

XIV Guarantee

• damages caused by faulty electrical installation of the Customer,

including the use of incorrect fuses;

• damages caused by Customer's failure to provide maintenance and

servicing activities defined in the operating manual;

• damages resulting from the use of spurious spare parts or

accessories improper for given model, repairing and introducing

alterations by unauthorized persons;

• defects caused by operating faulty Device or accessories.

15. The scope of the guarantee repairs shall not include periodic

maintenance and inspections, in particular cleaning, adjustments,

operational checks, correction of errors or parameter programming

and other activities that should be performed by the user (Buyer).

The guarantee shall not cover natural wear and tear of the Device

and its components listed in the operating manual and in technical

documentation as such elements have a defined operational life.

16. If a defect is not covered by the guarantee, the Manufacturer

reserves the right to remove such defect at its sole discretion,

repairing the damaged or destroyed parts or providing components

necessary for repair or replacement.

17. This guarantee shall not exclude, limit or suspend the Customer

rights when the provided product is inconsistent with the purchase

agreement.

This Device may be used with all devices

certified with Z-Wave certificate and should be

compatible with such devices produced by

other manufacturers.

Any device compatible with Z-Wave may be added

to Fibaro system.

FIBARGROUP

FIBARO

In case of any technical questions contact customer service centre

in your country.

www.fibargroup.com

Fig. 4 Roller Shutter icon in Home Center interface

NOTE

Parameters 12 and 17 settings are automatically

modified only in Home Center 2 controller, when

choosing one of Gate Modes. In case of controllers

from other manufacturers these parameters need

to be set manually (see section XV).

NOTE

Installation of the gate driver may be performed

only by certified professionals. The motor must be

equipped with the appropriate limit switches (see

Fig 2). It’s recommended to connect a NC

(normally closed) contact of an IR barrier to S2

terminal. Opening the contact will stop the gate. In

addition, it’s recommened to connect an

emergency stop button to the motors neutral (N)

wire. In emergency, pushing the emergency stop

button will cut the power and stop the gate. It is

recomended to monitor regulary operation of

Fibaro Roller shutter in all modes. Also it is

recomended to regulary verificate and maintenan-

ce connectors.

NOTE

S1 and S2 terminals react to mains voltage only.

Using IR barriers with NC contacts operating on

lower voltages require using an additional relay

(see Fig. 2)

Default setting: 0

Parameter size: 1 [byte]

SCENES AND ASSOCIATIONS SETTINGS:

50. Scenes / Associations activation.

Parameter determines whether scenes or associations are

activated by the switch keys.

0 - Associations activation

1 - Scenes activation

Default setting: 0

Parameter size: 1 [byte]

BLUE - Roller Shutter calibration procedure (see pt. )

VIOLET - initiate the Z-Wave network range tester

GREEN - reset energy consumption data memory (see pt. )

YELLOW - Roller Shutter reset (see pt. )

Release the B-button to choose the desired function and confirm

your choice with the B-button click.

WARNING!

In Protection Mode it will not be possible to control

Fibaro Roller Shutter from buttons. It is not

recomended to control all Fibaro Roller Shutters in

this mode.

Especificaciones del producto

Marca:	Fibaro
Categoría:	No categorizado
Modelo:	Roller Shutter FGRM-222

¿Necesitas ayuda?

Si necesitas ayuda con Fibaro Roller Shutter FGRM-222 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

No categorizado Fibaro Manuales

Fibaro Double Switch 2 FGS-223 Manual de Usario

8 Septiembre 2024

Fibaro FIB_FGWPE-101 Manual de Usario

30 Agosto 2024

Fibaro FGWPB-111 Manual de Usario

28 Agosto 2024

Fibaro Roller Shutter FGRM-222 Manual de Usario

27 Agosto 2024

Fibaro FGWOE-011 Manual de Usario

26 Agosto 2024

Fibaro FGBS-001 Manual de Usario

26 Agosto 2024

Fibaro FGBWHWPF-102 Manual de Usario

25 Agosto 2024

Fibaro FGBS-222 Manual de Usario

25 Agosto 2024

Fibaro FGR-222 Manual de Usario

24 Agosto 2024

Fibaro FGBWHWPE-102 Manual de Usario

23 Agosto 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024

Philips 43PUL7672 Manual de Usario

27 Octubre 2024

Manhattan 461504 Manual de Usario

27 Octubre 2024

Sungrow SG125HV Manual de Usario

27 Octubre 2024

Schneider CCT724319 Manual de Usario

27 Octubre 2024

Technoline WS 250 Manual de Usario

27 Octubre 2024

Livarno IAN 354423 Manual de Usario

27 Octubre 2024

Kupper 12152 Manual de Usario

27 Octubre 2024

JennAir CARBON24L Manual de Usario

27 Octubre 2024