Garmin VIRB Remote Manual de Usario

Garmin Mando a distancia VIRB Remote

Lee a continuación 📖 el manual en español para Garmin VIRB Remote (14 páginas) en la categoría Mando a distancia. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/14
VIRB™ Remote Instructions.............................................................................................................. 2
Instructions de la télécommande VIRB™.......................................................................................... 4
VIRB™ Istruzioni del telecomando.................................................................................................... 6
VIRB™ Fernbedienung – Anweisungen............................................................................................ 8
VIRB™ Instrucciones del mando a distancia................................................................................... 10
Instruções do controlo remoto VIRB™............................................................................................ 12
Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. VIRB™ and ANT+™ are trademarks of Garmin Ltd. or its subsidiaries. These
trademarks may not be used without the express permission of Garmin.
This product is ANT+™ certified. Visit for a list of compatible products and apps.www.thisisant.com/directory
July 2014 190-01627-90_0DPrinted in Taiwan
TA-2013/2179
TRA
REGISTERED No:
ER0127480/14
DEALER No:
DA0061884/11
VIRB™ Remote Instructions
Remote Overview
ÀRecord key. Select to record video on connected devices.
ÁPhoto key. Select to capture a photo on connected devices.
ÂStop key. Select to stop recording video on connected devices.
ÃStatus LED.
Status LED
LED Activity Status
Flashing green Searching for a paired device.
Alternating red and green Attempting to pair with a device.
12 rapid green flashes Successfully paired with a device.
Four rapid green flashes Successfully sent a command to a device.
Four rapid red flashes Failed to send a command to a device.
Flashing red Device is recording video.
Pairing the Remote with Your Device
The first time you connect the VIRB remote to your VIRB
device, you must pair the remote with your device.
1On the VIRB device, select > > to SETUP Remote Remote
turn on the remote control feature.
2On the VIRB remote, select any key.
The status LED starts flashing green.
3On the VIRB remote, hold two keys simultaneously until the
status LED starts alternating green and red, and release the
keys.
The remote searches for your VIRB device. When the
remote pairs successfully, the status LED flashes green 12
times.
After the remote is paired, it connects to your device whenever
the device is in range and turned on.
Using the Mounts
Several mounts are available for your remote, either included
with the product or as an optional accessory. The mounts allow
you to attach the remote to your body, your bike, or other
objects.
• Align two of the notches À with the sides of the mount, and
press the remote into the mount until it clicks.
• Press gently on the release tab Á, and lift the remote from
the mount.
Replacing the Battery
WARNING
Do not use a sharp object to remove batteries.
Keep the battery away from children.
Never put batteries in mouth. If swallowed, contact your
physician or local poison control center.
Replaceable coin cell batteries may contain perchlorate
material. Special handling may apply. See
www.dtsc.ca.gov.hazardouswaste/perchlorate.
CAUTION
Contact your local waste disposal department to properly
recycle the batteries.
Before you can replace the battery, you must have a small
Phillips screwdriver, a small flat screwdriver, and a CR2032
lithium coin-cell battery.
1Using a Phillips screwdriver, remove the three screws from
the back plate À.
2Remove the back plate from the remote.
3Wrap the end of a small flat screwdriver with tape.
The tape protects the battery, battery compartment, and
contacts from damage.
4Carefully pry the battery from the back plate.
5Install the new battery into the back plate with the positive
side facing down.
6Verify the gasket Á is fully seated in the groove.
2
7Replace the backplate, aligning the post  with the gap in
the circuit board Ã.
8Replace and tighten the three screws.
NOTE: Do not overtighten.
Specifications
Battery type User-replaceable CR2032, 3 volts
Battery life Up to 1.5 years (1 hour per day)
Operating temperature
range
From -10° to 50°C (from 14° to 122°F)
Radio frequency/protocol 2.4 GHz ANT+™ wireless communications
protocol
Water rating 5 ATM*
*The device withstands pressure equivalent to a depth of
50 meters.
3

Especificaciones del producto

Marca: Garmin
Categoría: Mando a distancia
Modelo: VIRB Remote

¿Necesitas ayuda?

Si necesitas ayuda con Garmin VIRB Remote haz una pregunta a continuación y otros usuarios te responderán


Mando a distancia Garmin Manuales

Garmin

Garmin VIRB Remote Manual de Usario

13 Septiembre 2024

Mando a distancia Manuales

Últimos Mando a distancia Manuales

Monacor

Monacor DRM-880WP Manual de Usario

27 Octubre 2024
Hama

Hama Spot-Pointer V2 Manual de Usario

26 Octubre 2024
Sony

Sony RM-ED022 Manual de Usario

21 Octubre 2024
Sonos

Sonos Control Manual de Usario

18 Octubre 2024
One For All

One For All URC 7935 Manual de Usario

18 Octubre 2024
Canon

Canon BG-E20 Manual de Usario

12 Octubre 2024
Neewer

Neewer RT112 Manual de Usario

8 Octubre 2024
Neewer

Neewer RT113 Manual de Usario

8 Octubre 2024
Logitech

Logitech Harmony 785 Manual de Usario

8 Octubre 2024
DSC

DSC WS4949 Manual de Usario

8 Octubre 2024