Golden Age Project R1 Tube Active Manual de Usario

Lee a continuación 📖 el manual en español para Golden Age Project R1 Tube Active (2 páginas) en la categoría micrófono. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/2
It also makes the R1 Tube Active able to drive long
microphone cables without any problems and insures
that the sound is consistent with dierent preamps. One
of the factors that usually changes the sound of passive
ribbon microphones is the input impedance of the fol-
lowing microphone preamp. The active output circuitry
in the R1 Tube Active buers the ribbon and the gain
make-up transformer from the outside world and the
result is that the R1 Tube Active will consistently give
you maximum performance in any situation.
The R1 Tube Active is very well suited for the recording
of most sound sources like vocals, acoustic instruments,
strings, horns, orchestras and choral groups and many
live sound applications.
In spite of its low cost, the R1 Tube Active meets the
most stringent demands.
To get maximum benet and trouble free use out of the
R1 Tube Active, please read this manual carefully.
UNPACKING, INSPECTION STORAGE AND
TRANSPORT
The R1 Tube Active was carefully tested and packed at
the factory. The aluminium case has been designed to
protect the microphone when you store, ship or move it.
Please always use it when you need to transport the R1
Tube Active for service or for any other reason.
IMPORTANT NOTICE:
The ribbon assembly in the R1 Tube Active, as in any
ribbon microphones, is very sensitive and fragile and can
be easily damaged if handled the wrong way,
That is why it is important that you immediately aer
you have received the R1 Tube Active, veries that it
is working properly and that it has not been damaged
during shipping.
The warranty of the ribbon assembly in the R1 Tube
Active does not extend beyond this initial inspection,
since it can be damaged so easily if it isn´t handled
properly.
In the rare case that the R1 Active is not working prop-
erly when receiving it, please contact your dealer.
FEATURES
- The unmatched natural and musical sound of a clas-
sical ribbon microphone combined with the consistent
sound quality oered by the addition of active electronics.
- A low-noise 12AX7 tube amplier that isolates the
ribbon and gain make-up transformer from the outside
world.
- A stunning realism with the feeling of “being-there”.
- The typical large and mellow ribbon sound quality
with a very smooth top end and an extended low end.
- A fast and life-like transient reproduction.
- An ultra-high SPL capability, 165 dB SPL (1% THD @
1000Hz) and a very high sensitivity for a ribbon micro-
phone, similar to many condenser microphones.
- A Figure-8 directional paern for wide sweet spots
both in the front and in the back of the microphone. Zero
spots towards the sides.
- A 50 mm long ribbon made of 2 microns thick alu-
minium foil.
- An internal shock mount for the ribbon and magnet
assembly.
- A removable microphone cable and a
nice aluminium ight case.
- Manufactured of the nest materials
for a great performance and long-term
reliability.
- The R1 Tube Active can be used with
any standard mixer or preamp, prefer-
ably with a balanced input.
USE OF THE R1 TUBE ACTIVE
Connect the supplied cable between the
R1 Tube Active and the power supply
with the power switch o. Then
connect a standard balanced XLR
microphone cable between the 3-pin
XLR connector on power supply to
the preamp or mixer. The R1 Tube
Active power supply needs 115
or 230V AC power. For optimum
performance, let the R1Tube Active
warm up for at least 15 minutes
before use.
The Figure-8 paern of the R1
Tube Active gives you the ability to
separate sound sources by placing
the unwanted ones in the side zero
w w w . g o l d e n a g e p r o j e c t . c o m
I
Vintage Style Tube Active Ribbon Microphone
INTRODUCTION
Congratulations on choosing the Golden Age Project R1 Tube Active microphone!
The R1 Tube Active is a unique microphone since it is one of the very few high quality vintage style
ribbon microphone with active tube electronics on the market and especially since it probably is the
rst low cost one!
The R1 Tube Active oers the unique and natural sound that has been available in classical micro-
phones like the RCA 44 and 77 that are still used to make high quality recordings today aer
almost 70 years. On top of that, the active tube circuitry gives you that special tube intimacy,
warmth and sparkle. It also raises the output level considerably to be similar to that of many con-
denser microphones. This has the good eect that one does not need special high gain microphone
preamps when using the R1 Tube Active on quiet sound sources.
pick-up directions. Placing the unwanted ones towards
the sides of the R1 Tube Active will remove most of the
direct sound from the sound source. The R1 Tube Active
will still pick up that source from the reverberant eld
in the recording room though. Due to the small width of
the ribbon, the horizontal pick-up paern is very wide.
It is much wider compared to a large capsule condenser
microphone.
The vertical pick-up paern is narrow at the higher
frequencies though due to the length of the ribbon. This
is due to the fact the wavelength at higher frequencies
is much shorter than the length of the ribbon. If you
want maximum top end response from the R1 Active,
it is important that the R1 Active is mounted so that it
is parallel to the sound source. If it is vertically angled
against the sound source, then there will inevitably be
a loss of top end. This can sometimes be a good thing
so this eect can be used creatively. The narrow vertical
pick-up paern will lower the eect of high frequency
sound reections.
Be aware of the proximity eect (an increase in bass
response) when the R1 Tube Active is close to the sound
source. This can be a good or a bad thing. You can adjust
the bass response by changing the distance from the
microphone to the sound source for an optimum result
in dierent situations. You can also use a high-pass lter
in your preamp or mixer.
PRECAUTIONS
- Make sure that you select the proper voltage on the
voltage selector on the power supply before connecting
the unit to 115 or 230V AC power, otherwise the unit will
be damaged! This is not covered by the warranty.
-The transducer part of the R1 Tube Active consists of a
very thin and ultra-light corrugated aluminium ribbon
clamped under light tension and mounted between the
poles of a strong magnet. When the sound waves hits the
ribbon and moves it, a small current is generated in the
ribbon since it is suspended in a magnetic eld.
The good part of this design is that it results in one of
the warmest and most natural sound available from
any type of microphone. The bad part of it is that it also
make ribbon microphones the most sensitive and fragile
ones. It is therefore very important that the R1 Tube
Active, as any other ribbon microphone, is treated with
very special care if it is not to be seriously damaged.
In order to ensure a long life for your R1 Tube Active,
please always follow these guidelines:
1. Do never subject the R1 Tube Active to hard knocks,
such as dropping it or not packing it properly when you
move or transport it since this can destroy the ribbon
assembly.
2. Do never blow into the R1 Tube Active and protect it
from any strong blast of air movement as this can tear
and destroy the fragile ribbon.
3. Do never move around fast with the R1 Tube Active
in your hand, please remember that any excessive air
movement can damage the ribbon.
4. Do always use a pop-lter when there is a risk of
excessive air movements reaching the ribbon from the
sound source. One example is close-up vocals. The pop-
lter will also protect the R1 Tube Active from mouth spray.
5. Do always protect the R1 Tube Active from dirt and
moisture.
6. Do never use phantom power with the Tube R1
Active.
7. When the R1 Tube Active is not in use, always keep it
in its aluminium case.
8. Do always store the R1 Tube Active in a vertical posi-
tion. If it is stored horizontally, the 50 mm long ribbon
can sag by time which will gradually degrade the per-
formance of the R1 Active.
9. Avoid exposing the R1 Tube Active to direct sunlight
or extremes in humidity for extended periods of time.
10. Do never try to service the R1 Active yourself since
this will void the warranty.
WARRANTY
- Due to the extremely delicate nature of ribbon micro-
phones which can so easily be damaged by improper
handling and use, the ribbon assembly is not covered
under warranty.
Please check your R1 Tube Active carefully immediately
when you receive it and make sure that there are no
problems with the microphone. Aer that rst initial
inspection, the standard one year warranty (90-days on
the tube) only apply to defects in materials and work-
manship in parts other than the ribbon assembly.
If the ribbon assembly is damaged during use, contact
your dealer or us for a quote for replacement of the
ribbon assembly.
service@goldenagemusic.se
SPECIFICATIONS
Type: Large ribbon geometry, pure aluminium, 2 um
thick, 50 x 5 mm size with active electronics.
Polar paern: Figure 8
Frequency response: 30 Hz – 18 kHz +/- 3 dB
Sensitivity: -40 dB (0 dB = 1V/Pa) @ 1 kHz.
Equivalent Noise Level (A-weighted per
IEC 268-4): < 16 dB typical.
Maximum SPL (<1% THD @ 1 kHz): 165
dB.
Output impedance: 200 ohm, balanced.
Recommended load impedance: > 1000
Ohms.
Dimensions: 69x185 mm.
Weight: 1 500 g.
Please note: Specications can be
changed at any time without notice.
Many thanks for purchasing the
Golden Age Project R1 Tube Active
- We wish you much joy and many
wonderful recordings with it!
w w w . g o l d e n a g e p r o j e c t . c o m
II

Especificaciones del producto

Marca: Golden Age Project
Categoría: micrófono
Modelo: R1 Tube Active

¿Necesitas ayuda?

Si necesitas ayuda con Golden Age Project R1 Tube Active haz una pregunta a continuación y otros usuarios te responderán




micrófono Golden Age Project Manuales

micrófono Manuales

Últimos micrófono Manuales