Golden Lighting Heartwood 8063-M1L BUS Manual de Usario

Golden Lighting Alivio Heartwood 8063-M1L BUS

Lee a continuación 📖 el manual en español para Golden Lighting Heartwood 8063-M1L BUS (9 páginas) en la categoría Alivio. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/9
Canopy 1ea Hex nut 2ea Wire
connectors 2ea
Mounting
bracket 1ea Mounting screws 2ea Socket rings 1ea
Deco Nut 2ea Fixture mounting
screws 2ea Socket washer 1ea
12" Rod 2ea 6" Rod 1ea
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad nish)
Comments
PARTS & ASSEMBLY SHEET
This xture assembled PO:__________ Date: ________
Fixture Name: Heartwood 8063-M1L BUS
Notice: Please review the parts listing and check for all parts before assembling the xture. If any parts
are missing or damaged, please note onthis sheet and contact the place of purchase to arrange for
replacement parts.
PARTS LIST Company Name:_______________________Co. Account #:_____________
to be lled out by retailer
8063-M1L BUS
Read and review installation instruction sheet, but
do not install before assembling the xture.
F A IIXTURE SSEMBLY NSTRUCTIONS
For Customer Service, contact the place of purchase to arrange for replacement parts.
NOTE: INSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
1. By measuring determine correct number of rods
needed for proper hanging height. There are 2 optional
12" rods included.
2. To shorten the xture trim the wires to the desired
length plus at least 8~10 inches.
2b. Slide the 6" rod plus the excess 12" rods o the wire.
2c. Thread the 6" rod back onto the wire then thread the
wire through the swivel conection into the canopy.
3. To lengthen the xture pull all the wire out of the
canopy.
3b. Slide the 6" rod o the wire.
3c. Thread the additional rods with the 6" rod last back
onto the wire then thread the wire through the swivel
conection into the canopy.
Fig 1
V
These two Rods may
be removed
or
additional Rods may
be added.
ROD-12 BUS
Fig 2
For Customer Service, contact the place of purchase to arrange for replacement parts.
PARTS & ASSEMBLY SHEET
Fixture Name: Heartwood 8063-M1L BUS
4. Pull the xture’s wire through the Rods until taut.
5. Thread Rod Q into Frame R until tight. ( )
6. Thread Rod P into Rod Q) until tight. repeat for ( )
any additional rods.
7. Thread 6" Rod W into Rod P until tight. ( )
8. Loosen the Set screw ( X ) just until the rod will t in
the swivel coupler. Thread the 6" Rod W into the ( )
canopy ( N ) and tighten the Set screw( X )
* You may now install the xture.
9. Place the glass shade (S) over the threaded socket
(V) and place the Socket Washer (T) onto the threaded
socket (V) and secure both by threading the Socket ring
(U) until tight.
10. Install the light bulb in accordance with the xture’s
specications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING!) V
W
X
Fig. 1
Fig. 2
For Customer Service, contact the place of purchase to arrange for replacement parts.
HANGING THE FIXTURE as Semi ush (Fig. 1)
1. Carefully remove the new xture from the carton and
the yellow bag that holds all your parts. Check that all
parts are included as shown in the illustration and parts
list.
2. Shut o power at the circuit breaker and remove the old
xture from ceiling, including the old mounting strap.
3. The Mounting bracket ( C ) contains several pairs of
threaded holes, nd the pair of holes that match the hole
spacing in your xture Back Plate (N) and thread the two
Mounting Screws (B) half way into the Mounting Strap (C)
facing down, these will have their threaded ends protrude
through the two holes in the xture canopy(N).
4. Place the Mounting Strap ( C ) over the junction box
5. Attach the Mounting Strap (C) to the Junction Box using
the two mounting screws (E). Tighten the screws (E)
securely with screw driver.
CONNECTING THE WIRES (Fig 2)
6. Attach the power supply wires to the xture lead wires
by connecting BLACK to BLACK (or SMOOTH) and
WHITE to WHITE (or RIBBED).
7. Attach the GROUND wire(GREEN or COPPER) from
the Junction Box and the xture Ground wire to the green
Ground Screw (F) on the Mounting Bracket (C) or
connect both wires together using the correct size of wire
connectors. -
NOTE:Twist the wires together in the same direction you
twist the wire connector onto the wires.
8. Tuck these wire connections neatly into the Junction
Box.
FINISHING THE INSALLATION (Fig.3)
9. Place the xture’s canopy over the Mounting Bracket
(C) and over the Mounting Screws (B), adjust the xture
canopy (N) until the Mounting Screws (B) protrude out
from the canopy (N) and secure the xture against the
ceiling by threading the decorative nuts(O) until tight.
10. Install the light bulbs and glass shade as per the
xture assembly sheet.
YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE
FIXTURE.
Fig. 3
For Mini Pendant Light Fixture
INSTALLATION INSTRUCTIONS
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
Fixture Name: Heartwood 8063-M1L BUS
N

Especificaciones del producto

Marca: Golden Lighting
Categoría: Alivio
Modelo: Heartwood 8063-M1L BUS

¿Necesitas ayuda?

Si necesitas ayuda con Golden Lighting Heartwood 8063-M1L BUS haz una pregunta a continuación y otros usuarios te responderán




Alivio Golden Lighting Manuales

Alivio Manuales

Últimos Alivio Manuales