Hager EE840 Manual de Usario

Hager detector de movimiento EE840

Lee a continuación 📖 el manual en español para Hager EE840 (4 páginas) en la categoría detector de movimiento. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

+ 90°/- 30°

Description

Detection zone

Installation

Setting

15 min

5 s

5 min

auto -+

lux

test

Accessories for corner  xing

Plate for wall  xing

Detection head

Connection by PIN system

(4 plug-in pins)

Vertical adjustment

The optimal height of installation is 2.5 m.

The detection  eld must remain free.

2,5 m

α = 360°

Ø 12 m

3 m

6 m

Fixed time

(length of time

of lighting)

Luminosity Sensitivity

(modi cation

of the range)

Setting potentiometers

Ligthing loads

Incandescent, halogen 23

Halogen ELV (12 or 24 V)

via ferromagnetic or elect

transformer

Compactfluo

Parallel compensated fluo

Electronic ballast

Caution!

This device is to be installed only by a professional

electrician  tter according to local applicable

installation standards.

Do not plug in or unplug this product when it is live.

DETECTOR 360°

EE840 White

EE841 Charcoal

ACCESSORY FOR

CORNER FIXING

EE855 White

EE856 Charcoal

6E7574.C1

6E7574.C

EE84.

izMotion detector comfort 360°

Testing and validating

the detection zone

Put the potentiometer on Test mode. The Test 2

mode is available for 3 min.

Every movement detected switches on the light for

1s. After 3 min without detection of movement, the

product returns to normal operation.

Limiting the detection zone

You can limit the detection zone by tilting the

head.

“Normal” operation (on/off)

The lighting is activated whenever the level of

luminosity dened by the potentiometer is 2

judged to be insufcient and a movement is

detected.

After detection, the light stays on for the length

of time predened by the potentiometer .1

The xed timing is reset after each detection.

Please note: when the potentiometer is on “auto

test”, the settings are predened.

Control by timer

An impulse is generated every 10 s whenever the

level of luminosity is judged to be insufcient and

a movement is detected when the potentiometer

1 is on .V

This pulse mode is not suitable for connections to

power devices (except at low power loads).

Operating precautions

In order to obtain optimal detection conditions, it is recommended that the following advice:

- the detection is sensitive to solar radiation and bad weather. Detection performance is optimal up to

35 °C and above 40 °C.

- It is preferable to maintain à distance of 1 m. between a light source and the detector.

When mounting on a box, make sure that you do not distort the wall plate through excessive tightening

of the screws.

Montage

Surface-mounting or ceiling-mounted :

- x the wall plate using the screws provided

- connect the wall plate terminal block (see cabling plans in annex)

- fully insert the detector on the wall plate

- tighten the screws to ensure the product is sealed.

For corner xing, the wall plate is to be xed between the accessory and the detector.

Cable entry (breakable partitions) are possible:

- by the back (box mounting) or by the bottom.

Action Settings Potentiometer

Use Auto settings

(factory) to switch the

light automatically for

a given time.

Auto Settings

Put the Lux potentiometer on

“auto test”.

The settings are predened:

Lux = (operating at night only)o

time = 3 min,

sensitivity = max.

Automatically switch

on the light for a

defined time.

Installer settings

Control a timer, a bell

etc. Impuls V

Auto settings are usable with

time = 1s. (cannot be changed)

Test and validate the

detection zone. Test mode

Move the potentiometer 2 to

“auto test”.

Adjust the sensitivity. Allows setting the range

to avoid disturbance.

Product presentation

and operating principles

This detector allows automatic control of a

light source for a dened length of time when a

movement is detected in the surveillance zone.

Settings and Test

The detectors have 2 modes of operation:

Fixed time and Control by timer.

Power supply

The detector switches the light on for 40 s.

After 40 s, it activates the Normal mode.

10A AC1 230 V~

30 1500 W

tronic 1500 VA

10 x 20 W

orescent tubes 400 WÓ/ C=45 µf

580 W

60 mm

LN S'

Ateha raceways

ref. ATA 12200

or ATA 63000

Wiring and connections (provide installation with xed wiring)

6E7574.C2

+ 90°/- 30°

6E7574.C

Beschrijving

Detectiezone

Installatie

Instelling

15 min

5 s

5 min

auto -+

lux

test

Afdekplaten

Wandmontageplaat

Detectiekop

Aansluiting d.m.v. PEN-systeem

(4 insteekbare pennen)

Verticale instelling

De optimale montagehoogte bedraagt 2,5 m.

Het detectieveld moet vrij zijn.

2,5 m

α = 360°

Ø 12 m

3 m

6 m

Tijdvertraging

(verlichtingsduur)

Lichtsterkte Gevoeligheid

(wijziging van

het bereik)

Instelpotentiometers

Belastingstype

Gloeilampen, 230 V-halog

ZLS-halogeenlampen (12

ferromagnetische of elekt

Compacte TL-lampen

Parallel-gecompenseerde

Elektronische voorschake

6E7574.C

EE84.

ziBewegingsmelders comfort 360°

Opgelet!

Het toestel mag alleen door een elektroinstallateur

worden geïnstalleerd volgens de installatienormen

die van toepassing zijn in het land.

De contactpennen van het product niet vast- of

loskoppelen wanneer het onder spanning staat.

360°-BEWEGINGSMELDER

EE840 Wit

EE841 Zwart

TOEBEHOREN VOOR

HOEKMONTAGE

EE855 Wit

EE856 Zwart

Especificaciones del producto

Marca:	Hager
Categoría:	detector de movimiento
Modelo:	EE840
Color del producto:	Wit
Peso.:	181 g
Ancho:	85 mm
Profundidad:	124 mm
Altura:	24.6 mm
Fuente-de-alimentación:	Batterij/Accu
Capacidad del acumulador/batería:	500 mAh
Bluetooth:	Ja
Puerto USB:	Ja
Batería/Voltaje de la batería:	7.4 V
Resolución-Máxima:	313 x 400 DPI
Conector USB:	Micro-USB Type-A
Otros sistemas de apoyo:	Android, iOS
tecnología de impresión:	ZINK (Zero ink)
Tiempo hasta la primera página (color, normal):	45 s
Consumo medio de energía durante la impresión:	- W
Dimensiones máximas de impresión:	2" x 3" (5x7.6 cm)
Tecnología de batería:	Lithium-Polymeer (LiPo)