Hobart 6801 Manual de Usario

Hobart máquina de aserrar 6801

Lee a continuación 📖 el manual en español para Hobart 6801 (12 páginas) en la categoría máquina de aserrar. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/12
FORM 34405 Rev. C (August 2011)
MODEL 6801 MEAT SAW
MODEL
6801 ML-134094
PREVIOUS MODELS COVERED BY THIS MANUAL:
6801 ML-104948
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
937 332-3000
www.hobartcorp.com
– 2 –
Installation, Operation, and Care of
MODEL 6801 MEAT SAW
SAVE THESE INSTRUCTIONS
GENERAL
The 6801 Meat Saw is rugged, durable, and easy to clean. The saw is equipped with a water resistant
3 HP electric motor and direct gear drive transmission. The carriage (Fig. 1) has stainless steel ball
bearings providing easy travel and dependability. The shaped front edge of the carriage is comfortable to
the operator's body even when leaned on during movement. The carriage lock is standard.
Table, carriage, pulleys, guides, and wiper assemblies can be quickly removed without tools for ease of
cleaning. Moving parts are enclosed but accessible. The blade is guarded above and below the cutting
zone. The pusher plate is provided to eliminate the need of handling items close to the blade; it can ride
on the right "anged-end" of the carriage so you keep your hands away from the cutting edge of the blade.
For electrical specications above 250 volts, a transformer provides a 115 volt control circuit voltage.
Thermal overload protection is an option.
One long-life blade is furnished with each saw as standard equipment. This blade cannot be re-sharpened;
replacement blades are available through your local Hobart Service Ofce.
© HOBART, 1995, 2000
PL-41385-1
UPPER PULLEY COVER (SST)
COLUMN GUARD
GAUGE PL EAT
TABLE (RIGHT)
GAUGE PL E HANDLEAT
LOCK LEVER
LOWER COVER (SCRAP N)PA
LEGS
FEET
CARRIAGE LOCK
CARRI EAG
TABLE (LEFT) SAW BLADE
UPPER GUIDE AND GUARD
SWITCH KNOB
Fig. 1
– 3 –
INSTALLATION
UNPACKING AND ASSEMBLY
Immediately after unpacking the meat saw, check for possible shipping damage. If the meat saw is found
to be damaged, save the packaging material and contact the carrier within 15 days of delivery.
Prior to installation, test the electrical service to make sure it agrees with the specications on the machine
data plate located on the column.
Packed in a packet attached to the table compartment are the pusher plate and the gauge plate handle.
Place the pusher plate in its storage location under the carriage support (Fig. 2). Assemble the gauge
plate handle to the gauge plate support by screwing the stud into the threaded hole (Fig. 3).
LEVELING
Place the saw in its operating location. Using a spirit level, level the meat saw front-to-back and side-to-
side by turning the threaded feet in or out.
PL-52107
Hand Knob
Upper Guide
and Guard
PL-41386-1
HAND KNOB
CARRIAGE
SUPPORT
SAW BLADE
CARRI EAG
PUSHER PL EAT
PL-41387-1
GAUGE PL E HANDLEAT
Fig. 2 Fig. 3
Fig. 4
Disconnect the electrical power to the machine and follow lockout / tagout
procedures.
SAW BLADE
The saw blade must be installed so the teeth point to the right and
down (Fig. 4).
UPPER GUIDE AND GUARD ASSEMBLY
When the saw is off, the hand knob (Fig. 4) can be used to raise or lower
the upper guide and guard assembly so the cutting zone is only as high
as necessary for the piece being cut. The hand knob is not loosened
during raising or lowering — it should remain tightly secure.

Especificaciones del producto

Marca: Hobart
Categoría: máquina de aserrar
Modelo: 6801

¿Necesitas ayuda?

Si necesitas ayuda con Hobart 6801 haz una pregunta a continuación y otros usuarios te responderán


máquina de aserrar Hobart Manuales

Hobart

Hobart 6801 Manual de Usario

5 Septiembre 2024
Hobart

Hobart 6614 Manual de Usario

5 Septiembre 2024

máquina de aserrar Manuales

Últimos máquina de aserrar Manuales

Hikoki

Hikoki C 6BU3 Manual de Usario

27 Octubre 2024
Dedra

Dedra DED7060 Manual de Usario

27 Octubre 2024
Einhell

Einhell KGS 190 Manual de Usario

27 Octubre 2024
Sun Joe

Sun Joe SWJ599E Manual de Usario

27 Octubre 2024
McCulloch

McCulloch CSE1935S Manual de Usario

27 Octubre 2024
Hikoki

Hikoki C10FSB Manual de Usario

27 Octubre 2024
Metabo

Metabo STA 18 LTX 150 BL Manual de Usario

26 Octubre 2024
Craftsman

Craftsman 917.377662 Manual de Usario

26 Octubre 2024
Maruyama

Maruyama MCV51 Manual de Usario

26 Octubre 2024
Powerplus

Powerplus POWX53300T Manual de Usario

22 Octubre 2024