Hobbywing Xerun V10 G3 Manual de Usario
Hobbywing
juguetes radiocontrolados
Xerun V10 G3
Lee a continuación 📖 el manual en español para Hobbywing Xerun V10 G3 (1 páginas) en la categoría juguetes radiocontrolados. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/1
02
FEATURES
• It’s a motor specially designed for high-level racing. The RMP of G3 Stock motor is significantly improved, the KV & torque are improved by 16% and 4% respectively, compared with the V10 G2 Stock motor.
• Lightweight. The G3 Modified & Stock motors only weigh 161g & 132g respectively, the weights are reduced by 11% & 21% when comparing with the V10 G2 motors.
• The built-in high precision Hall sensor combined with the high precision and balanced rotor guarantee outstanding linearity of the motor.
• The mechanical timing can be adjusted finely and smoothly; the skid-proof lines on the rear end plate of the motor guarantee stability of the timing after adjustment. For G3 Stock motors (10.5T~25.5T), the timing is
adjustable from 30 degrees to 60 degrees; for Modified motors (3.5T~8.5T), the timing is adjustable from 20 degrees to 50 degrees.
• The motor case is designed to be easy to dismantle for maintenance purposes and for the replacement of common wearing parts.
• The special shell design which makes the stator core expose to the air maximizes cooling. Big holes on the end plates of 10.5T~21.5T motors further help reduce heat; small holes on the end plates of 5.5T~8.5T motors
effectively keep sand or dirt from getting inside and damaging the motor(s).
• The use of high-performance stator core, heat(200 )-resistant wire, heat(200 )-resistant rotor with strong structure, imported high precision and high strength bearings, and copper solder tabs with super current ℃ ℃
endurance guarantees outstanding performance and super durability.
04
INSTALLATION & CONNECTION
• The three output wires (on the ESC) need to be soldered onto the motor, the wires are
differentiated by colors. In general, Blue/Yellow/Orange represents phase A/B/C respectively.
Please note the following points when mounting or connecting the motor.
• The M3 screws with the length (not longer than 8mm) are needed when mounting the
motor onto your vehicle.
• Please pay attention to the relevant marks (on the ESC) when soldering/connecting those
output wires to the motor and make sure that you will strictly follow the wiring order
(between the ESC & the motor) of “A-A, B-B, and C-C”.
• Please ensure the sensor cable is clean and undamaged when you’re using a sensored ESC.
You need to pay attention to the two connectors on the cable when connecting the ESC to
the motor.
• Re-check all the connections between the ESC & the motor and ensure that they are all
correct (as shown in the diagram) before tur ning on the ESC.
Sensor wire Blue power wire (motor phase “A”)
Yellow power wire (motor phase “B”)
Orange power wire (motor phase “C”)
Switch
ESC
Input TH
Channel
(Ch.2)
Receiver
Servo
Battery Positive (Red)Battery Negative (Black)
- + S
1
CAUTIONS
CAUT I ONS
AT T ENT ION
USER MANUAL
V10 G3
05
TIMING ADJUSTMENT
The V10 G3 motors provide a wide range of adjustable mechanical timings, the following are the methods & principles you can follow when adjusting the timing.
• You can adjust the motor timing after unfastening the screw on the rear end plate. Please adjust the timing as needed according to the mark (/white lines)
at the rear end of the motor and fasten the screw after the adjustment.
For obtaining the optimal performance, you can change the output range and characteristic of your power system through adjusting the motor timing.
For the (10.5T~25.5T) Stock motors, the default timing is 40 degrees; for the (3.5T~8.5T) Modified motors, the default timing is 30 degrees.
As shown in the picture, turn the rear end plate clockwise can reduce the timing and turn it counter-clockwise can increase the timing.
• Increasing the timing can increase the motor speed (/RPM), while that also increases the motor temperature and reduces the efficiency. A high(er) timing
usually requires a high(er) ratio.
• Please ensure your ESC is properly programmed before setting the motor timing. For detailed information about ESC programming, please refer to the
user manual of the ESC.
• After the timing adjustment, please ensure that your motor will not get overheat after running a whole pack (i.e. LiPo). You can get the information about
the motor temperature via a infra-red temperature gun or the LCD program & a laptop (with the Hobbywing USB Link APP installed) or the WiFi module &
smart phone (with the Hobbywing WiFi Link App installed). If the temperature is too high, please let the motor cool down first and then test again. If the
OPTIONS
09
Notes:
• The KV value is measured when no load is applied to the motor, the motor timing is set to the value by default and the ESC timing is set to Zero. The default timing for the 3.5T~8.5T
motors is 30 degrees, and the default timing for the 10.5T~25.5T motors is 40 degrees.
• Never allow the motor to get overheat, because high temperatures may affect its performance. Please let the motor cool down before using it again in case that it gets too hot.
• The input current corresponding to the maximum output power can be instructive for load configuration & ESC selection, we strongly suggest not allowing the load to be higher tha
the input current corresponding to the maximum output power.
03
SPECIFICATIONS
RECOMMENDED FDR
06
3.5T 4.5T 5.5T 6T 6.5T
7.4 1：
6.6 1：
35mm
10.0 1：
10.2 1：
12.6 1：
7T
7.3 1：
6.4 1：
36mm
9.5 1：
9.7 1：
12 1：
Modified
TC (Small Track)
TC (Big Track)
1/12th TC
2WD Off-road
4WD Off-road
4WD Truck
8.2 1：
7.5 1：
29mm
7.8 1：
7.0 1：
32mm
10.8 1：
11.8 1：
13.5 1：
7.6 1：
6.8 1：
34mm
10.5 1：
11.0 1：
13 1：
25mm
7.5T
7.2 1：
6.2 1：
36mm
9.1 1：
9.3 1：
11.5 1：
8T
7.1 1：
6.1 1：
37mm
8.7 1：
8.9 1：
11 1：
8.5T
7.0 1：
6.0 1：
38mm
8.25 1：
8.5 1：
10.4 1：
N/A
N/A
10.5T
5.5 1：
5.0 1：
42mm
8.0 1：
8.0 1：
9.0 1：
STOCK
TC (Small Track)
TC (Big Track)
1/12th TC
2WD Off-road
4WD Off-road
4WD Truck
13.5T
4.7 1：
4.0 1：
51mm
7.0 1：
7.0 1：
8.0 1：
17.5T
4.0 1：
3.5 1：
66mm
6.0 1：
6.0 1：
7.0 1：
21.5T
3.5 1：
3.0 1：
66mm
5.5 1：
5.5 1：
6.5 1：
25.5T
3.2 1：
2.7 1：
66mm
5.2 1：
5.2 1：
6.2 1：
Table
One
Table
Two
Thanks for purchasing Hobbywing XERUN V10 G3 motor. This sensored brushless power
system is very powerful, any improper usage can be dangerous and may damage the product
and related devices. Please take your time and read through the following instructions before
you start using the motor. We have the right to modify the product design, appearance,
features and usage requirements without notification. We, Hobbywing, are only responsible
for our product cost and nothing else are result of using our product.
PARTS LIST
08
The V10 G3 motor contains the following parts:
Front End Plate x 1Pcs
Rotor x 1Pcs
Stator x 1Pcs
Sensor Module x 1Pcs
Short Screws (M2.50) x 1Pcs
Long Screws (M2.50 x 45mm) x 3Pcs
Sensor Wires (80mm, 200mm) x 2PcsRear End Plate x 1Pcs
30401106
30401102
30401116
30401107
30401117
30401109
30401118
30401110
30401119
30401111
30401112
30401103
30401104
30401105
30401113
9450
7340
6500
5900
5500
5120
4800
4420
4200
3970
4500
3710
2830
2250
1500
0.0018
0.0029
0.0035
0.0041
0.0048
0.0056
0.0065
0.0074
0.0089
0.0097
0.0158
0.0251
0.0402
0.0645
0.1055
7.7
6.7
5.5
5
4.5
3.9
3.5
3.3
3
2.8
5.5
4.5
3.9
2.8
1.6
462
457
443
426
415
402
364
346
320
298
260
216
152
118
79
126
122
118
115
113
113
106
100
88
84
74
59
42
32
23
3.5T
4.5T
5T
5.5T
6T
6.5T
7T
7.5T
8T
8.5T
10.5T
13.5T
17.5T
21.5T
25.5T
Model
(Turns)
PN
KV
(No-load)
Resistance
( )Ω
1S
LiPos
No-load
Current
(A)
Max.
Output
Power
(W)
Current
@Max.
Output
Power (A)
Diameter/
Length
(mm)
Shaft
Diameter/
Length (mm)
Stock
Rotor Weight
（ ）g
Poles
Applications
Φ5-12.1
Φ5-12.3
2
Φ7.3-12.5
-U
Φ7.3-12.3
-U
Φ5-12.5
Ø=35.9mm
(1.41in)
L=51.2mm
(2.01in)
Ø=35.9mm
(1.41in)
L=50.5mm
(1.99in)
Ø=3.17mm
(0.125in)
L=14mm
(0.55in)
35.9/51.2mm
(1.41in/2.01in)
3.17/13
（ ）0.125in/0.51in
Ø=3.17mm
(0.125in)
L=13.3mm
(0.52in)
163 5.75oz（ ）
163 5.75oz（ ）
159 5.60oz（ ）
163 5.75oz（ ）
162 5.71oz（ ）
164 5.78oz（ ）
161 5.68oz（ ）
161 5.68oz（ ）
160 5.64oz（ ）
163 5.75oz（ ）
133 4.69oz（ ）
133 4.69oz（ ）
131 4.62oz（ ）
135 4.76oz（ ）
154 5.43oz（ ）
2S
2-3S
Modified Class of 1/10
th &
1/12th On-road Racing
1/10th Drift, 2WD Off-road Racing
Stock Class of 1/10
th On-road Racing
1/10th Stock Class Racing,
Rock Crawler
Modified Class of 1/10
th
4WD Off-road Racing
1/10th Drift, Stock Class of 1/10
th
On-road Racing
The FDR (Final Drive Ratio) is the ratio between the angular velocities of the pinion gear and the tyres. In simple terms, the number of laps the motor will rotate when the tyres spin one lap.
Different conditions like track type, grip, tyres, temperature, vehicle weight, gearing mode, driving mode influence the performance of your vehicle and have different requirements on the power system, therefore
one FDR can not be applicable for all conditions.
All the values in Table One are the FDRs recommended for vehicles using different G3 Modified motors; all the values in Table Two are the FDRs recommended for vehicles using different G3 Stock motors in the
Blinky mode. If you don’t know how to set the FDR, please refer to the following tables. If no recommended FDR is applicable to your vehicle, please start with a big FDR and then adjust gradually as per the
demand.
Notes:
• For the modified applications (listed above), please do not set the ESC timing to a very high value, because overload may damage your motor. If you have no idea about the timing setting, please start with 0 and
increase the value gradually, and ensure the motor temperature won’t go above 90 (/194 ).℃ ℉
Rotor x1
Stator x1
Sensor module
x1
Short screws x1
M2.50
Long screws x3
M2.50 x 45mm
Rear end plate
x1
Install the rear end plate Install the rotor
Fasten the rear end plate with those long screws Finished product
Install the sensor module
Install the front end plate
1 2 3
4 5 6
07
The XERUN V10 G3 Motor is very strong in construction but also easy to disassemble for maintenance.
We recommend checking the bearings and cleaning the motor periodically..
Please follow the steps (as shown below) to assemble the motor. When disassembling the motor, the sequences are reversed.
ASSEMBLY & DIS-ASSEMBLY
• To avoid short circuits, ensure that all wires and joints must be well insulated before connecting the
motor to related devices.
• Never allow this product or other electronic components to come in contact with water, oil, fuel or
other electro-conductive liquids. If it happens, stop the use of the product immediately and let it
dry carefully.
• Read through the manuals of all power devices and chassis and ensure the power configuration is
rational before using this unit.
• Never apply full throttle if the pinion gear is not mounted on, because (under the no-load
circumstances) high RPMs may get the motor damaged.
• Please connect all the devices carefully, you may not control the vehicle properly or encounter some
unpredictable issues like damaged components if any poor connection exists.
• To avoid possible damage (result from overheat) to the product, please control the soldering time within
5 seconds when soldering the motor wires (a soldering iron with the power of at least 60W is needed).
• Stop immediate usage once the casing of the motor exceeds 100 /212 as high temperature ℃ ℉
may damage the motor and cause the rotor to demagnetize. Hobbywing recommends activating
the “Motor Thermal Protection” (of the ESC).
PNOptional Part Part Name Description
30820018
30820017
30820019
30820020
30820400
Applications (/Motors)
10.5T-21.5T
3.5T-8.5T
3.5T-8.5T
3.5T-8.5T
25.5T
XERUN-V10-G3-Rotor-D7.3*D12.5*t24.1
XERUN-V10-G3-Rotor-D5*D12.3*t24.1
XERUN-V10-G3-Rotor-D5*D12.1*t24.1
XERUN-V10-G3-Rotor-D5*D12.5*t24.1
XERUN-V10-G3-Rotor-D7.3*D12.3*t25.2
It’s the standard rotor for the (10.5T~21.5T) Stock motors; with this rotor,
torque & RPM of your motor won’t be bad.
With this rotor, your motor will have the better accelerating and braking linearity and high RPM.
With this rotor, your motor will have the better accelerating and braking linearity and be smoother
during the high-speed operation. It’s specially applicable for the track with intermediate/low grip.
It’s the standard rotor for the 5.5T~8.5T motors.
It’s a rotor specially designed for the 25.5T motor.
Rotor
Especificaciones del producto
| Marca: | Hobbywing |
| Categoría: | juguetes radiocontrolados |
| Modelo: | Xerun V10 G3 |
¿Necesitas ayuda?
Si necesitas ayuda con Hobbywing Xerun V10 G3 haz una pregunta a continuación y otros usuarios te responderán
juguetes radiocontrolados Hobbywing Manuales
25 Septiembre 2024
25 Septiembre 2024
25 Septiembre 2024
25 Septiembre 2024
25 Septiembre 2024
25 Septiembre 2024
25 Septiembre 2024
25 Septiembre 2024
25 Septiembre 2024
17 Septiembre 2024
juguetes radiocontrolados Manuales
- juguetes radiocontrolados ACME
- juguetes radiocontrolados Absima
- juguetes radiocontrolados Spektrum
- juguetes radiocontrolados Chicco
- juguetes radiocontrolados Carson
- juguetes radiocontrolados Amewi
- juguetes radiocontrolados Proline
- juguetes radiocontrolados Biltema
- juguetes radiocontrolados TacTic
- juguetes radiocontrolados Little Tikes
- juguetes radiocontrolados Revell
- juguetes radiocontrolados Futaba
- juguetes radiocontrolados Tamiya
- juguetes radiocontrolados Traxxas
- juguetes radiocontrolados ARRMA
- juguetes radiocontrolados Carrera
- juguetes radiocontrolados Graupner
- juguetes radiocontrolados Blade
- juguetes radiocontrolados JETI
- juguetes radiocontrolados Ninco
- juguetes radiocontrolados Multiplex
- juguetes radiocontrolados SAB
- juguetes radiocontrolados Ripmax
- juguetes radiocontrolados Maverick
- juguetes radiocontrolados Reely
- juguetes radiocontrolados Robbe
- juguetes radiocontrolados Lenoxx
- juguetes radiocontrolados Axial
- juguetes radiocontrolados FMS
- juguetes radiocontrolados E-flite
- juguetes radiocontrolados Flyzone
- juguetes radiocontrolados FrSky
- juguetes radiocontrolados WLtoys
- juguetes radiocontrolados Jada
- juguetes radiocontrolados HPI Racing
- juguetes radiocontrolados Kyosho
- juguetes radiocontrolados PowerBox Systems
- juguetes radiocontrolados Losi
- juguetes radiocontrolados Hobby Zone
- juguetes radiocontrolados JR
- juguetes radiocontrolados RC4WD
- juguetes radiocontrolados Sky Rider
- juguetes radiocontrolados DF-Models
- juguetes radiocontrolados ROCHOBBY
Últimos juguetes radiocontrolados Manuales
27 Octubre 2024
27 Octubre 2024
26 Octubre 2024
26 Octubre 2024
19 Octubre 2024
15 Octubre 2024
8 Octubre 2024
4 Octubre 2024
3 Octubre 2024
3 Octubre 2024