Hoymiles HMT-1800-6T Manual de Usario

Hoymiles cargador de bateria HMT-1800-6T

Lee a continuación 📖 el manual en español para Hoymiles HMT-1800-6T (2 páginas) en la categoría cargador de bateria. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

2. Installation Steps

1. Accessories

Step 1. Plan and install the Microinverter

All accessories above are not included in the package and should be purchased separately.

Note:

1. Install the microinverter and all DC connections under the PV module to avoid direct sunlight, rain exposure, snow buildup, UV, etc.

2. Leave at least 2 cm of space around the microinverter enclosure to ensure ventilation and heat dissipation.

3. Mounting torque of the 8 mm screw should be 9 N·m. Please do not over-torque.

The order of Step 1 and Step 2 can be reversed according to your planned needs.

Item Description

A 3P-AC Trunk End Cap

B 3P-AC Trunk Connector

C 3P-AC Trunk Port Disconnect Tool

D 3P-AC Trunk Connector Unlock Tool

E 3P-AC Trunk Port Cap

DC Extension Cable,1m

3P-AC Trunk Cable, 12/10 AWG Cable

- Use the 3P-AC Trunk Connector Unlock Tool

to unlock the connector upper cover.

1 ) Disassemble the AC Trunk Connector and remove the cable.

2 ) Install the 3P-AC Trunk End Cap at one side of 3P-AC Trunk Cable (The end of 3P-AC Trunk Cable)

3 ) Install AC end cable on the other side of 3P-AC Trunk Cable (connected to the distribution box)

- Loosen the three screws with screwdriver.

Untighten the cap and remove the cable.

*Note:

HMT-2250/1800-6T Quick Installation Guide

A ) Mark the position of each microinverter on the rail, according to the PV module layout.

Step 2. Plan and Build the 3P-AC Trunk Cable

B ) Fix the screw on the rail.

C ) Hang the microinverter on the

screws, and tighten the screws. The silver

cover side of the microinverter should be

facing the panel.

- Insert the 3P-AC Trunk End Cap and screw

the cap back to port, then tighten the cap.

- Unlock the port upper cover, loosen the screws

with screwdriver and remove the extra cable.

(Skip this step if there is no cable at this side.)

- Plug the upper cover back to the Trunk

connector.

5.5±0.5N·m

Mounting Torque : 9 N·m

click

B C D E F GHA

M8*25 screws (Prepared by the installer)

3P-AC Trunk Cable is used to connect the microinverter to distribution box.

A ) Determine how many microinverters you plan to install on each AC branch and prepare AC Trunk Connectors

accordingly.

B ) Take out segments of AC Trunk Cable as you need to make AC branch.

Step 5. Connect PV Modules

Step 6. Energize the System

A ) Mount the PV modules above the

microinverter.

B ) Connect the PV modules’ DC cables to the

DC input side of the microinverter.

Note:

1. Tightening torque of the cap: 5.5±0.5 N·m. Please do not over-torque.

2. Torque of locking screw: 0.4±0.1 N·m.

3. Do not damage the sealing ring in the 3P-AC Trunk Connector during disassembly and assembly.

Step 4. Create an Installation Map

A ) Peel the removable serial number label from

each microinverter.

B ) Affix the serial number label to the respective

location on the installation map (please refer

to the appendix).

Note:

1. Make sure that the 3P-AC Trunk Connectors are kept away from any water-channeling surface.

2. In case you need to remove the microinverter AC cable from 3P-AC Trunk Connector, please use

the 3P-AC Trunk Port Disconnect Tool and insert the tool into the side of AC Sub Connector to

complete the removal.

Product information is subject to change without notice. (Please download reference manuals at www.hoymiles.com).

C ) Repeat the above steps to make all the 3P-AC Trunk Cables you need, then lay out the cable on the rail in the suitable

position so that the microinverters can be connected to the Trunk connectors.

Step 3. Complete the AC Connection

Note: Please use DC extension cables.

- Prepare a segment of AC cable with suitable

lengthto connect to the distribution box, with

stripping requirements fulfilled.

- Insert the cable into the cap in a way that

theL1, L2, L3, PE and N lines are in correspond-

ing slots.

- Tighten the screws: and tighten the cap back

to the port.

- Plug the upper cover back to the Trunk

connector.

B ) Connect the AC end cable to the distribution box, and wire it to the local grid network.

A) Turn on the AC breaker for the branch circuit.

B) Turn on the main AC breaker for the house. Your

system will start to generate power in about two

minutes.

Step 7. Set up Monitoring System

Please refer to the DTU User Manual or DTU Quick Install Guide,

and Quick Installation Guide for S-miles Cloud to install the DTU

and set up monitoring system.

D ) Attach the 3P-AC Trunk Cable to the

mounting rail and fix the cable with tie wraps.

A ) Push the AC Sub Connector from

microinverter to the 3P-AC Trunk Connector

until it clicks.

C ) Please plug the 3P-AC Trunk Port Cap in

any vacant AC Trunk Port to make it water and

dust-proof.

5.5±0.5N·m

0.4±0.1N·m

click

8±1mm

70±5mm

To _ sheet _____

Sheet_____of_____

Ho ym ile s Micro invert e r In st all at ion Map

Please Make N for North

2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

COLUMN

ROW

AP040228 V1.3

Customer Information: DTU Serial Number

Azimuth:

Tilt:

Panel type:

Especificaciones del producto

Marca:	Hoymiles
Categoría:	cargador de bateria
Modelo:	HMT-1800-6T

¿Necesitas ayuda?

Si necesitas ayuda con Hoymiles HMT-1800-6T haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

cargador de bateria Hoymiles Manuales

Hoymiles HMT-1800-6T Manual de Usario

14 Septiembre 2024

Hoymiles HMT-2250-6T Manual de Usario

14 Septiembre 2024

Hoymiles HMS-1600 Manual de Usario

13 Septiembre 2024

Hoymiles HMS-1800 Manual de Usario

13 Septiembre 2024

Hoymiles HYS-4.6LV-EUG1 Manual de Usario

13 Septiembre 2024

cargador de bateria Manuales

Últimos cargador de bateria Manuales

Nitecore UHX1 PRO Manual de Usario

27 Octubre 2024

Nitecore EMR05 TAC Manual de Usario

26 Octubre 2024

Bosch GAA12V-21N Manual de Usario

24 Octubre 2024

Panasonic CF-VCB331 Manual de Usario

24 Octubre 2024

Ryobi One+ RC18627 Manual de Usario

21 Octubre 2024

Alecto BL-179 Manual de Usario

19 Octubre 2024

Graupner Ultramat 12 Manual de Usario

16 Octubre 2024

Graupner ULTRA DUO PLUS 30 Manual de Usario

16 Octubre 2024

MSW S-CHARGER-20A.2 Manual de Usario

15 Octubre 2024

MSW S-CHARGER-10A.2 Manual de Usario

15 Octubre 2024