HQ EL-PIR70 Manual de Usario

HQ detector de movimiento EL-PIR70

Lee a continuación 📖 el manual en español para HQ EL-PIR70 (66 páginas) en la categoría detector de movimiento. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/66

EL-PIR70

Radar motion sensor

This sensor is an active motion detector. The integrated HF sensor emits high-

frequency electro-magnetic wave (5.8GHz) and receives their echo. The sensor

detects the change in echo from even the slightest movement in the light’s detection

zone. A microprocessor then triggers the “switch light ON” command. Detection is

possible through doors, panes of glass or thin walls.

Detection zones for ceiling mounting

1) Minimum reach 1m dia.

2) Maximum reach 8m dia.

Detection zones for wall mounting

3) Minimum reach 1m dia.

4) Maximum reach 8m dia.

Important: persons or objects moving towards

the light are detected best!

Installation procedures

1. Take down the top cover by turning it anti-clockwise (see g.1), and then tighten off

the two screws xing middle cover (see g. 2);

2. Hold base against the wall and mark drill holes, paying attention to any existing

wiring in the wall;

3. Drill the holes, insert wall plugs (6mm dia);

4. Put the power wire and load wire through the base holes;

5. Screw the base into place (see g. 3);

6. Connect the mains power supply and the load wire to the connection terminal

according to connection-wire mark.

7. Close the middle cover (see g. 3) and adjust knob to setting;

8. Fit glass shade and turn it clockwise (see g. 3).

g 1 g 2 g 3

Technical specications

power supply: 220-240VAC

power frequency: 50/60Hz

Installation sit: indoors, wall/ceiling mounting

HF system: 5.8GHz CW radar, ISM band

transmission power: <10mW

rated load:1200W: 220-240VAC

detection angle: 360°, 160°

reach:1-8m (dia.), adjustable

time setting: 5sec to 15min

light control: 2~2000LUX

Connection illumination

connect N,L with power; connect N, L’ with load

Reach setting (sensitivity)

Reach is the term used to describe the diameter of

the more or less circular detection zone produced

on the ground after mounting the sensor at a height

of 2.5m, turn the reach control fully anticlockwise

to select minimum reach (approx.1 m dia), and fully

clockwise to select maximum reach (approx. 8m dia).

Time setting

The light can be set to stay ON for any period of time between approx. 5sec

(turn fully anticlockwise) and a maximum of 15min (turn fully clockwise).

Any movement detected before this time elapse will re-start the timer. It is

recommended to select the shortest time for adjusting the detection zone

and for performing the walk test.

NOTE: after the light switches OFF, it takes approx. 1sec before it is able to start

detecting movement again. The light will only switch on in response to movement

once this period has elapsed.

Light-control setting

The chosen light response threshold can be innitely from approx. 2-

2000lux. Turn it fully anti-clockwise to select dusk- to-dawn operation at

about 2 lux. Turn it fully clockwise to select daylight operation at about

2000lux. The knob must be turned fully clockwise when adjusting the

detection zone and performing the walk test in daylight.

1-8 dia

5sec~15min

2~2000LUX

Especificaciones del producto

Marca:	HQ
Categoría:	detector de movimiento
Modelo:	EL-PIR70
Color del producto:	Black, Blue, Grey
Peso.:	252 g
Ancho:	73 mm
Profundidad:	113.5 mm
Altura:	159 mm
Amable:	Draagbare streepjescodelezer
Indicadores LED:	Ja
Tiempo de carga:	4.5 uur
Capacidad del acumulador/batería:	2200 mAh
Tecnología de conectividad:	Bedraad en draadloos
Tipo de fuente de energía:	Battery, DC
Cables suministrados:	RS-232, USB
Señal de advertencia:	Ja
Número soportado de baterías/baterías:	1
Certificación:	FCC Part15 Class B, CE EMC Class B
versión USB:	2.0
Estación base de peso:	150 g
Tipo de sensor de imagen:	CMOS
Voltaje de entrada:	100 - 240 V
Rango de conexión:	30 m
Temperatura de almacenamiento:	-20 - 70 °C
Estación de carga:	Ja
Frecuencia:	50/60 Hz
Longitud de onda:	625 nm
Códigos de barras compatibles (1D):	Codabar, Code 11, Code 128, Code 39, Code 93, EAN-13, EAN-8, GS1 DataBar Expanded, GS1-128 (UCC/EAN-128), ITF-14, Interleaved 2 of 5, MSI, Plessey, U.P.C.
Interfaces estándar:	USB, RS-232, Zigbee
tipo de escáner:	1D/2D
Máx. escaneado:	752 x 480 mm
Dimensiones de la estación base:	82.5 x 195 x 47 mm
Temperatura de funcionamiento (TT):	-20 - 50 °C
Humedad relativa de funcionamiento (VV):	5 - 93 procent
Tecnología de batería:	Lithium-Ion (Li-Ion)
Tipo de Batería:	Ingebouwde accu
Rincón de lectura de propuestas:	-55 - 55 °
Admite códigos de barras 2D (matriciales y apilados):	Data Matrix, PDF417, QR Code
Niveles de luz (luz solar directa):	0 - 100000 Lux
Número de lecturas por implementación:	15000
Rincón de lectura de guiñada:	0 - 360 °
Rincón de lectura inclinable:	-55 - 55 °
conexión de ordenador:	RS-232/USB
Resolución del escáner:	5 mm