Joovy Peg Perego Car Seat Adapter Manual de Usario

Joovy Productos para bebes Peg Perego Car Seat Adapter

Lee a continuación 📖 el manual en español para Joovy Peg Perego Car Seat Adapter (2 páginas) en la categoría Productos para bebes. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

!WARNING

This infant car seat adapter is for use ONLY on the Joovy Zoom Joggers. DO NOT use on other stroller models.

This infant car seat adapter is for use ONLY with the Peg Perego® infant car seat models identied below. DO NOT use other infant car seat

models.

ALWAYS install the infant car seat so that the child is facing toward the rear (handlebar) of the stroller.

ALWAYS position the infant car seat so that it securely snaps into place inside the infant car seat adapter frame.

!WARNING

Before each use, check to make sure all four clamps are secure and all Velcro® straps are fully attached.

Installing/Using the Infant Car Seat Adapter

• UnsnapthevesnapslocatedonBOTHsidesoftheseat.See Figure 1.

• Foldthefabricinsideandunderthestrollerframetubessothatthetubesareclearlyexposedonbothsidesofthestroller.See Figure 2.

• Positionthecanopysoitisopenedhalfway.Reclinetheseattoitsmaximumreclineposition.See Figure 3.

• RemovetheVelcro®strapsfromeachclamp,thenopenallfourclampsontheadapter.

• Placethecarseatadapteronthestrollerframetubessothatthecanopyhingebracketsarebetweentheadapterclamps.See Figure 4.

DO NOT allow any of the seat fabric to be captured by the clamp.

• Closeallfourclampsaroundthestrollerframetubes.See Figure 5. Makesurethatallfourclampsarefullyclosedandnoseatfabricis

capturedbytheclamps.

• InserttheloopendofoneVelcro®strapbetweenoneadapterclampandtheseatfabric.Attachthelooparoundthetabontheclamp.

See Figure 6.

• WraptheVelcro®straptightlyaroundtheclamp.See Figure 7.

• EnsurethatthemiddleloopoftheVelcro®straptsovertheclamptab. See Figure 8.

• ContinuewrappingtightlyuntiltheentirelengthoftheVelcro®strapissecuredtogether.MakesuretheedgesoftheVelcro®strapare

alignedformaximumstrength.See Figure 9.

• RepeatfortheotherthreeclampsandVelcro®straps.

• Closethecanopycompletely.

NOTE: Tomaximizespaceforyourbaby,attachthetwosetsofsnapsfoundontheundersideofthecanopy.See Figure 10.

• PlacethePegPerego®infantcarseat(sothecarseatfacesthehandlebar)intotheadapteruntilthecarseatsnapsintoplace.Pullupon

thecarseattoensureitissecure.See Figure 11.

• Toremovetheinfantcarseat,pullthereleaselever(sameleverusedtoreleasethecarseatfromitsbase)andliftup.

NOTE: strollerfoldswithcarseatadapterinstalled.

Removing the Infant Car Seat Adapter

• Toremovethecarseatadapter,rstpositionthecanopysothatitisopenedhalfway.

• RemoveallfourVelcro®strapsfromtheclamps.

• Openallfourclampsandremovetheadapterfromthestroller.

• ReattachthefourVelcro®strapstotheclampsontheadapterandstoretheadapterforfutureuse.

• WraptheseatfabricoverthestrollerframetubesandreattachthevesnapslocatedonBOTHsidesofthestroller.

Zoom

Peg Perego® Car Seat Adapter

00951

PEG PEREGO® CAR SEAT ADAPTER COMPATABILITY

Peg Perego® Primo Viaggio

Figure 1

Figure 7

Figure 2

Figure 8

Figure 5Figure 4

Figure 11Figure 10

Figure 6

Figure 3

Figure 9

©joovy 2013 • Document Version 091313

Joovy•2919CantonStreet•Dallas,TX75226•(877)456-5049•Fax:(214)761-1774Email:customerservice@joovy.com•Website:www.joovy.com

Especificaciones del producto

Marca:	Joovy
Categoría:	Productos para bebes
Modelo:	Peg Perego Car Seat Adapter
Peso.:	90.71 g
Ancho:	49.022 mm
Profundidad:	95.25 mm
Altura:	17.78 mm
Indicadores LED:	Stroom
Tipo de embalaje:	Doos
Puerto USB:	Ja
Tipo de conector USB:	USB Type-A
Cables suministrados:	USB
Resolución de grabación:	1920 x 1080 Pixels
País de origen:	China
Certificación:	FCC, CE
Formato de señal analógica:	Niet ondersteund
versión USB:	3.2 Gen 1 (3.1 Gen 1)
Certificados de sostenibilidad:	RoHS
Soporta Windows:	Windows 10, Windows 7, Windows 8, Windows 8.1
Tipo de comida:	USB
Número:	1
Temperatura de almacenamiento:	-10 - 70 °C
Interno:	Nee
Soporta el sistema operativo Mac:	Mac OS X 10.10 Yosemite, Mac OS X 10.11 El Capitan, Mac OS X 10.12 Sierra, Mac OS X 10.9 Mavericks
Compatibilidad con Mac:	Ja
Compatible con Linux:	Ja
Guía de Instalación Rápida:	Ja
Interfaz de host:	USB 3.2 Gen 1 (3.1 Gen 1)
Entrada HDMI:	1
Requerimientos mínimos del sistema:	Intel Core i5-3400, NVIDIA GT630 / AMD R9 200, 4 GB RAM
Procesador mínimo:	Intel Core i5-3400
RAM mínima:	4096 MB
Temperatura de funcionamiento (TT):	0 - 40 °C
Humedad relativa de funcionamiento (VV):	10 - 90 procent