K&K Sound Definity System Manual de Usario

K&K Sound No categorizado Definity System

Lee a continuación 📖 el manual en español para K&K Sound Definity System (5 páginas) en la categoría No categorizado. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/5
92798 Cape Arago Hwy, Coos Bay, OR 97420 | 541-888-3517 | Toll Free 1-800-867-6863 | www.kksound.com
D E F IN I T Y S Y S T E M
GENERAL PICKUP INFORMATION
The Definity pickup is a hybrid of a compression
pickup and a soundboard transducer. Its super-thin
and flexible design allows for a variety of
applications especially on instruments with floating
bridges.
The Definity System is paired with the Definity
Preamp, which is optimized for the Definity pickup
and a very important part of the system. The Definity
Preamp features a phase switch, which is particularly
important for this pickup. Please see p. 3 for more
information on the phase switch.
We found the Definity System performs best when
the pickup is installed so that part of it is under
pressure by the floating bridge and part of it is “free
floating” to pick up vibrations like a sound board
pickup.
It is not necessary for the Definity pickup to cover the
entire area of a bridge or bridge foot. As a general
rule, you want to aim for a placement that allows
approximately half of the pickup under a bridge
(compression) and the other half free on the
soundboard. There are some exceptions for
instruments with narrow bridges, like banjos. (More
detailed information on this on p. 4.) But it is a good
strategy for Archtop or Maccaferri/Selmer guitars
and many other floating bridge instruments.
This manual will describe installation techniques and
locations that we have tested to deliver the best
results for a variety of popular floating bridge
instruments.
GENERAL INSTALLATION PROCEDURE
1. Mark the position of the bridge on the
soundboard with tape. Make sure the tape
will not interfere with the position of the
Definity pickup. Then loosen the strings and
move the bridge out of the way to allow
mounting the pickup.
2. Install the Definity pickup so that the bridge
stands on its front portion and the back half
(where the cable exits) sticks on the
soundboard, similar to how it is shown on
one of the photos below.
3. Remove the red release foil on the bottom of
the pickup and stick the transducer in place.
4. Move the bridge back into position and
secure the gray cable of the pickup with tape
so it does not cause noise.
2
92798 Cape Arago Hwy, Coos Bay, OR 97420 | 541-888-3517 | Toll Free 1-800-867-6863 | www.kksound.com
5. The jack can be mounted at a convenient spot
near the endpin of the instrument.
6. Coil up extra cable and secure it, e.g. with
clear tape.
OUTPUT JACK
The Definity pickup comes with a Switchcraft stereo
endpin jack wired in mono. It has a self-adhesive
removable clip attached to it. This jack also allows
for internal mount when the clip is removed. If go
this route, it may require you to temporarily unsolder
the pickup during installation. Please consult a
skilled technician if you choose this option.
Too remove the clip please use a slot screwdriver to
open the snap tab (see photo). Then remove the
black electrical tape that is wound around the jack.
This tape only builds up the diameter of the jack to
match the clip.
INTERNAL JACK INSTALLATION
1. For internal mount only, skip this section if
you are using the clip.
2. Drill or widen the endpin hole to 1/2" using
protective tape to cover the area around the
hole. This helps to prevent chips and
scratches.
3. Unscrew the endpin jack's strap mount knob.
4. Take off the nut and washer.
5. Find out the thickness of your end block and
set the nut on the cap accordingly (see
picture below). Once in place, screw the cap
in as far as it goes.
6. Insert the jack from the inside into the endpin
hole. Tip: a chopstick or something similar
helps to get a hold of the jack and pull it
through the hole.
7. Attach outside washer and nut and tighten.
Use a small Allen wrench or similar in the
small front holes of the jack to hold on while
tightening the nut. Attach the end knob and
tighten by hand.
Important: Make sure that the strap knob screws in
ALL THE WAY over the outer threaded part of the
jack, so that a tiny portion of the thread is exposed
when the strap-knob is tightened. If you don’t do this,
you might experience insufficient signal transmission
and sound cutting in and out.
THE DEFINITY PREAMP
Open the lid of the box (it just pulls off – it snaps back
on) to get access to the battery compartment and to
the adjustment options inside the preamp.
Install a 9-volt battery in the battery compartment.
There are midrange and treble trim-potentiometers
(trim-pots) that can be adjusted with a small
screwdriver. When the little white arrow in the center
of the trimmer is in the 12 o’ clock position, the
setting is flat with no cut or boost. Turning the pots
counterclockwise cuts frequencies, and turning
clockwise boosts frequencies. Mids are centered at
1250Hz (X- -wide band Q) and treble are at 8000Hz
(high shelf).
On the battery side of the circuit board is a phase
(toggle) switch with a small white tab. It has a big
effect on feedback control and on overall tone. There
is a detailed description of the effect on the phase
setting below. Move the white tab left or right (2
positions) and listen. There will be one setting that
sounds better with less feedback.
3
92798 Cape Arago Hwy, Coos Bay, OR 97420 | 541-888-3517 | Toll Free 1-800-867-6863 | www.kksound.com
CONNECTION TO AMPLIFIER
Use a regular guitar cable (not supplied) to connect
the output-jack of the pickup with the input of the
preamp. Connect the output of the preamp to an
amplifier with a regular mono guitar cord. Please
note that a stereo cable will NOT switch on the
preamp.
USING THE PHASE SWITCH
The Definity Preamp has a miniature phase switch
mounted on the battery side of the circuit board. It is
a sliding switch (a small white tab) that you can slide
to the left and right with your finger or with a small
screwdriver. There are only two settings.
The Pure XLR Preamp has a push-release phase
switch on the back.
Phase switches are usually marketed as a feedback
controlling device, but they accomplish more than
just that. A phase switch inverts the amplified sound
wave so that it does not interfere with the original,
un-amplified sound coming from your instrument.
Every acoustic instrument projects sound waves into
the air at a certain phase when it is played
unplugged. For optimal sound amplification, the
phase that is projected from the amplified speaker
source needs to be "in phase" with the acoustic
instrument's own acoustically generated sound
waves.
The problem is that amplification systems, effect
units, or any electronic audio device may or may not
invert the phase of the incoming signal. The
manufacturers do not specify. An out-of-phase
problem is indicated by early feedback and
somewhat tinny, unbalanced sound. This may be
tolerable in some tone ranges and quite noticeable
in others, even resulting in sound cancellations on
some notes.
By toggling the phase switch back and forth on the
Definity Preamp or pushing/releasing it on the Pure
XLR Preamp, you will notice fuller, warmer, and
nicely balanced tone with less feedback in one
setting. This is the correct phase switch setting. Keep
in mind that it may be different with different
amplification systems.
DEFINITY PRO WITH PURE XLR PREAMP
The Pure XLR Preamp operates on 12–48 volt
Phantom Power or 9-volt battery. The LED light on
the front-panel indicates if phantom power is present.
In order to save battery life it will not light when the
unit is running on battery power.
With phantom power, the battery will not be drained
as long as the phantom power provides more than
10 volt.
FRONT:
BACK:
CHANGING THE BATTERY
To insert and change the battery, open the 2 screws
on the sides of the unit, remove the lid, connect a
new 9-volt battery to the battery clip and place it in
the marked compartment.
The unit is delivered without a battery.
UNPLUG THE INPUT CABLE IN ORDER TO SWITCH
OFF THE BATTERY!
ADJUSTABLE GAIN CONTROL
Gain and volume both have an effect on the output
volume of the preamp, but they accomplish different
tasks.
The gain (also called input gain or sensitivity control)
is located at the INPUT of the circuit. It sets the
amount of pre-amplification before the signal enters
the EQ section, DI etc. The volume control is located
at the OUTPUT (the very end of the circuit) and
simply allows you to adjust the volume.

Especificaciones del producto

Marca: K&K Sound
Categoría: No categorizado
Modelo: Definity System

¿Necesitas ayuda?

Si necesitas ayuda con K&K Sound Definity System haz una pregunta a continuación y otros usuarios te responderán


No categorizado K&K Sound Manuales

K&K Sound

K&K Sound Trinity Pro Preamp Manual de Usario

12 Septiembre 2024
K&K Sound

K&K Sound Mandolin Twin Fusion Manual de Usario

12 Septiembre 2024
K&K Sound

K&K Sound Definity System Manual de Usario

12 Septiembre 2024
K&K Sound

K&K Sound Big Twin Manual de Usario

12 Septiembre 2024
K&K Sound

K&K Sound Bass Master Rockabilly Plus Manual de Usario

12 Septiembre 2024
K&K Sound

K&K Sound Pure Mini Manual de Usario

12 Septiembre 2024
K&K Sound

K&K Sound Pure Preamp Manual de Usario

12 Septiembre 2024
K&K Sound

K&K Sound Dual-Channel Pro Preamp Manual de Usario

12 Septiembre 2024
K&K Sound

K&K Sound Twin Spot Internal Manual de Usario

12 Septiembre 2024
K&K Sound

K&K Sound Volume Control Manual de Usario

12 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024