K&K Sound Mandolin Twin Fusion Manual de Usario

K&K Sound No categorizado Mandolin Twin Fusion

Lee a continuación 📖 el manual en español para K&K Sound Mandolin Twin Fusion (5 páginas) en la categoría No categorizado. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/5
92798 Cape Arago Hwy, Coos Bay, OR 97420 | 541 888 3517 | Toll Free 800 867 6863 | kksound.com- - - -
M A N D O L IN T W I N F U S IO N
Thank you for choosing the Mandolin Twin Fusion!
This pickup system can easily be installed by the musician. It provides the same great sound as the
fully internal Mandolin Twin System offered by K&K Sound but it does not require any permanent
alteration to your instrument.
INSTALLATION
1. The picture shows the desired locations of the two transducers
inside the mandolin. In some models the two braces will run
differently than shown here.
If a brace does not allow you to place the pickup next to the
exact center (the widest part) of the F hole, just move the pickup
up or down a bit until you find a spot that fits the transducer.
However, move it a little as possible from the position shown.
2. The materials you will need for installation, from left to right:
Scissors, tweezers (if you do not have tweezers handy, a pair of
small needle-nose pliers will work just fine). In the sales
package, locate the bent nail (this is your installation tool), the
putty piece (gray putty on brown/white paper), the double-stick
tape (on brown/white paper), and, of course, the pickup.
92798 Cape Arago Hwy, Coos Bay, OR 97420 | 541 888 3517 | Toll Free 800 867 6863 | kksound.com- - - -
2
3. Apply double stick tape to the golden side of the transducers, it is a very thin film:
We recommend applying two layers of the double stick tape. After the first layer is applied as shown, peel
off the brown protective tape. Repeat the procedure. This helps to reduce the sensitivity towards unwanted
mechanical transmissions and guarantees the most secure adhesion.
4. Put the transducers into the treble side F-hole. If you have a pick-guard, remove it temporarily.
Maneuver the bass side pickup over to the bass side F hole, - and fish it out with tweezers or needle-nose
pliers.
5. Locate the putty piece and form a round ball from it.
92798 Cape Arago Hwy, Coos Bay, OR 97420 | 541 888 3517 | Toll Free 800 867 6863 | kksound.com- - - -
3
6. Stick the putty over the bent nail (your installation tool) onto the
labeled-black side of the pickup. Make sure to hold the pickup so the
cable leads towards the bottom of the mandolin once the pickup is
attached to the soundboard. The putty will temporarily hold the pickup
to the bent nail.
Test if the brace inside the mandolin allows free access to the pickup’s
desired location. By holding on to the nail you can carefully move the
pickup around inside the mandolin and test the fit. Aim for a spot next
to the widest part of the F hole, closest to the bridge.
Once youve established the desired spot make sure the putty still
securely adheres to the pickup. It can be re-shaped and re-positioned if
needed.
7. Remove the brown protective paper from the double stick tape on the
pickup and bring the pickup into position.
8. Use upward pressure on the installation tool to firmly press the pickup
to the soundboard.

Especificaciones del producto

Marca: K&K Sound
Categoría: No categorizado
Modelo: Mandolin Twin Fusion

¿Necesitas ayuda?

Si necesitas ayuda con K&K Sound Mandolin Twin Fusion haz una pregunta a continuación y otros usuarios te responderán




No categorizado K&K Sound Manuales

No categorizado Manuales

Últimos No categorizado Manuales