Kent Jindabyne Manual de Usario

Kent Calentador Jindabyne

Lee a continuación 📖 el manual en español para Kent Jindabyne (12 páginas) en la categoría Calentador. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/12

Tested and approved to Australian Standards

AS/NZS 2918 and AS/NZS 4013/4012.

Prior to installation check with your state and local

authorities regarding any specific regulations that

may apply.

Please keep these instructions for future

reference.

Burn hardwood only.

COVERS MODELS - JINDABYNE (STD FIRE BOX)

COUNTRY CLASSIC (STD FIRE BOX)

SOMERSET (SLIM LINE FIRE BOX)

Owners Manual

Wood Heaters

For All

FIRST THINGS FIRST...

Congratulations on your purchase of a quality Kent wood heater. This product is designed according to strict

environmental, quality and safety standards and should give you years of trouble free home heating.

Read these instructions carefully to get the most out of your heater and to ensure safe and satisfactory heater

performance. In particular, we would like to draw your attention to these warnings.

Be careful of what you burn:

Protect yourself and your family

from burns:

Use only dry, well seasoned hardwood.

Do not use coal or briquettes.

Do not burn garbage in the firebox as garbage

can cause a dangerous soot build up and

increase the amount of smoke your heater

produces.

Do not burn chemically treated timber as the

poisonous gases given off could damage your

stove.

CAUTION: THE USE OF SOME TYPES OF

PRESERVATIVE-TREATED WOOD AS

FUEL CAN BE HAZARDOUS.

Do not place any types of builders board eg

fibro, cement sheeting (or any other materials

not specified and tested by the manufacturer)

inside the firebox.

The exterior surfaces of the heater will

become hot during operation. For protection

of children, the elderly or infirm, provide a

firescreen to prevent contact with the

appliance in operation.

To protect against injury from burns, use

caution when operating the appliance. In

particular, when loading the firebox, provide

adequate protection for your hands.

WARNING: DO NOT USE FLAMMABLE

LIQUIDS OR AEROSOLS TO START OR

REKINDLE THE FIRE.

WARNING: OPEN AIR CONTROL BEFORE

OPENING FIRING DOOR.

Use your heater according to these

instructions:

The heater can get very hot, so

watch obvious fire hazards:

CAUTION: THIS APPLIANCE SHOULD BE

MAINTAINED AND OPERATED AT ALL

TIMES IN ACCORDANCE WITH THESE

INSTRUCTIONS.

DO NOT BURN WITH DOOR OPEN.

WARNING: ANY MODIFICATION OF THE

APPLIANCE THAT HAS NOT BEEN

APPROVED IN WRITING BY THE TESTING

A U T H O R I T Y I S C O N S I D E R E D A S

BREACHING AS/NZS 4013.

WARNING: DO NOT STORE FUEL WITHIN

HEATER INSTALLATION CLEARANCES.

CAUTION: THIS APPLIANCE SHOULD NOT

BE OPERATED WITH A CRACKED GLASS.

Do not throw logs into the firebox. Always

place logs carefully.

Load logs with ends pointing to the front of the

heater. This will help prevent logs rolling

forward.

Do not overfire (allow firebox to glow red) as

this could damage your firebox.

Always leave a minimum of 25mm (1) of ash

in the bottom of the firebox. Never empty it

completely.

The appliance or flue system should not be

modified in any way without the written

approval of the manufacturer.

Do not place clothing or other combustible

materials on top of the heater.

Do not store flammable liquids near the

heater.

Do not store fuel close to the stove.

*WARNING: DO NOT USE FLAMMABLE

LIQUIDS OR AEROSOLS OR PLACE

THESE IN THE VICINITY OF THIS

APPLIANCE WHEN IT IS OPERATING.

Exclusion of Liability

Whilst every care has been taken in formulating these instructions, no responsibility whatsoever will attach to

and/or claim lie against, the manufacturer and/or the distributor of the heater as a result of any failure to follow

the whole or any part of the instructions and/or as a result of incorrect information herein and/or any omission

here from.

ASSEMBLING YOUR NEW HEATER

There are a number of heaters in the Kent range. The heaters are mounted on columns, which require some

assembly. All heaters will require

firebrick and baffle plate assembly.

Convection models are supplied with fans, which will need to be assembled.

Column Assembly

There are a few different column styles. Some do

not require screws: you assemble the column by

inserting the tags located at either end of the front

and rear panels. Push the front and rear panels

down to lock tags into position. The column can

be further secured if you wish by fitting self

tapping screws into the holes provided between

the tags (screws not provided).

Other side panels have nuts and screws

provided for you to screw the panels together.

If your heater comes with a fan, the side panels

will have two holes at the top for securing the fan.

These must face the rear of the firebox.

Next, fit the aluminium heatshield to the top of the

column, ensuring the

shield locates in the

slots at the top of the

column.

You must now attach

the firebox. Lay the

firebox on its back.

Locate the column

onto the four locating

points on the base of

the heater. Ensure the

side of the column with a 45 mm gap on the

bottom edge goes at the rear of the heater.

Secure the column to the base of the heater with

the four self tapping screws provided.

Now stand the heater and column assembly up

and place into the base.

(For Jindabyne only) Fit the top deflector and

rear heatshield to the rear of the firebox by

pushing the long screws through the holes on the

back firebox panel. Fit

the top deflector first,

then the spacers, rear

heatshield and finally the

n u t s .

Secure

tightly.

Deflector & Heat Shield

Fan Assembly

Fix the fan to the

column using the

f o u r l o c a t i n g

screws provided.

The earth wires on

the fan will need to

be fixed to the

column. Refer to

detail view below.

The fan can be removed

f o r c l e a n i n g b y

unscrewing the locating

screws. Remember to

disconnect the power

supply before touching

the fan.

Firebricks (Standard Firebox)

Standard sized fireboxes use 7 firebricks and a

ceramic base liner in the arrangement shown

below.

Place the base liner down so that it is flush

against the front of the firebox. Place two

firebricks on each side laying down. Place

three firebricks at the back standing upright.

Now place the brick retainer along the back

firebricks so that the lip hangs over the front of

the bricks.

If necessary, push the side bricks towards the

back of the heater so they sit against the brick

retainer. This arrangement prevents the back

bricks from falling forward.

Especificaciones del producto

Marca:	Kent
Categoría:	Calentador
Modelo:	Jindabyne
Color del producto:	Zwart
Peso.:	494 g
Ancho:	13.97 mm
Profundidad:	18.11 mm
Altura:	3.18 mm
Material de la carcasa:	Metaal
Capacidad de almacenamiento interno:	1 GB
red LAN:	Ja
ventilador incorporado:	Nee
Consumo de energía (máx.):	15 W
Certificación:	Regulatory/environmental compliance:\nEMC Class A: FCC, CE, KC, RCM, VCCI
HDCP:	Ja
Número de DisplayPorts:	1
Tipo de procesador:	Ja
Software incluido:	Matrox PowerWall:\nhttps://www.matrox.com/graphics/en/products/video-wall/powerwall/
LAN Ethernet, velocidades de transferencia de datos:	1000 Mbit/s
Tecnología de cableado:	10/100Base-T(X)
Temperatura de almacenamiento:	-40 - 70 °C
Humedad de almacenamiento:	5 - 95 procent
Montaje en bastidor:	Ja
Cantidad de puertos RJ-45:	1
Versión DisplayPort:	1.2
Número de puertos de salida HDMI:	4
Temperatura de funcionamiento (TT):	0 - 45 °C
Humedad relativa de funcionamiento (VV):	20 - 80 procent
Ubicación de la fuente de alimentación:	Extern