Kenwood XM65R Manual de Usario

Kenwood Vocero XM65R

Lee a continuación 📖 el manual en español para Kenwood XM65R (6 páginas) en la categoría Vocero. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/6
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from your new power amplier.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the
model and serial numbers whenever you call upon your KENWOOD dealer for information or service on the product.
Model XM65F Serial number
Model XM65R Serial number
© 2023 JVCKENWOOD Corporation
XM65F
XM65R
6.5” COAXIAL SPEAKERS DESIGNED AND ENGINEERED TO CONNECT
AND MOUNT TO HARLEY-DAVIDSON® RUSHMORE PLATFORM
TOURING MODEL MOTORCYCLES
INSTRUCTION MANUAL
JVCKENWOOD Corporation
US Residents Only
Register Online
Register your KENWOOD product at https://registerkenwood.us.jvckenwood.com/
Contents
Section 1: XM65F Front Speaker Installation Instructions in FLH (Batwing) Models....2
Section 2: XM65F Road Glide Specific Front Speaker Installation Instructions.............4
Section 3: XM65R Rear Speaker Installation Instructions..................................................4
Warranty Info...............................................................................................................................5
KENWOOD XM65F and XM65R speakers will work best when powered by
an amplier. They have an impedance of 2 ohm and will cause damage if
wired directly to the built-in power of a non-2 ohm stable radio.
2
Section 1 - XM65F Front Speaker Installation
Instructions in FLH (Batwing) Models
Installation procedure
1. With your ignition switch in the “OFF” position, remove your outer fairing/headlamp
assembly and set it aside. Refer to a service manual if you need help with this. NOTE:
Placing a towel on the front fender can help prevent scratches or “dings” from dropped
tools or fasteners, etc.
2. Speaker Cabinet Removal: On the brake side speaker cabinet, carefully remove the
cable going into the power port/cigarette lighter assembly. If your bike has the CB module
(mounted “sideways” on the clutch side cabinet), undo the antenna cable and main
harness. The CB module will stay attached to the clutch side cabinet when removed. Undo
the speaker wire plugs going into each cabinet (pink & pink with black stripe wires).
Safety precautionsSafety precautions
CAUTION
To avoid the risk o f human injury or propert y
damage, be sure to read and observe the following
safety precautions:
• Consult a professional technician for installing and
connecting the speaker. — Incorrect installation may
lead to trac accidents or malfunctions.
• Avoid installation where the speaker in unstable. —
Make sure that the speaker is stationary and does not
rattle. Displacement of the speaker may cause injury.
• Do not modify the speaker. — Doing so may result in
smoke or re.
• Keep the volume of sound at an optimum level. —
Not being able to hear sounds from your surroundings
can lead to trac accidents.
• In case of abnormality, stop the use and disconnect
the speaker. — If operation is continued, smoke or re
may result. Disconnect the speaker and ask servicing.
• Always wear protective eyewear during installation.
• To prevent short-circuit, keep all wiring away from
moving parts, sharp edges, cut metal, etc.
• When removing or installing the grille, be careful not
to brush the unit with the edge of the grille.
• Do not switch ON power until wiring is completed.
FOR PROPER INSTALLATION AND USE
Please read the instructions carefully before using
this speaker:
• Be careful not to accidentally kick or apply any sort of
strong impact to the speaker.
• To prevent damaging the speaker, turn o the power
of the amplier before connecting it to the speaker.
• Do not use the provided parts for other purposes
Otherwise malfunction or re hazard could result.
NOTE
Observe the following cautions to prevent damage
to the speakers:
• You cannot input the same power as “peak power”
continually.
• When the volume is set too high, the sound may be
distorted or abnormal. Reduce the volume promptly in
case of such phenomena.
Section 1 - XM65F Front Speaker Installation Instructions in FLH
(Batwing) Models - Cont.
NOTE: We STRONGLY suggest completing the speaker swap on one side and then moving
to the other side. Figures 1.1 and 1.2 have arrows that point to the factory fasteners that
will be removed to allow the cabinets to come out of the bike. Although the brake side is
shown below, fastener locations are common for both brake and clutch side cabinets.
3. Installing the New Speaker: With the cabinet removed from the bike, undo the 4
screws that hold the factory speaker to the cabinet. Carefully take o each speaker wire
by disconnecting one at a time. Take the KENWOOD speaker and attach the factory
speaker wires, noting they will only go on one way. Using the factory screws, attach the
KENWOOD speaker to the cabinet. The factory speaker grille can be left in or replaced
with the supplied metal mesh grille using the 3 factory screws on the inside of the fairing.
In the KENWOOD grille, you will see two holes and one “keyhole” where the screws go
through and into the fairing. The keyhole in the KENWOOD grille needs to be oriented so
it is closest to the radio on each side for proper tment. Using the factory grilles will cause
a slight reduction in high-frequency volume. With the grilles in place and the speaker
properly attached to the speaker cabinet, the cabinet can be re-installed.
Repeat Step 3 for the second cabinet. Plug the factory speaker wires back into the
cabinet’s speaker wires and your speakers will be ready to test. Make sure to plug the
power cable back into the power port/cigarette lighter assembly on the brake side. If your
bike has the CB module, make sure to re-install the antenna cable and main harness. Then,
re-install your fairing and windshield.
3
Figure 1.1 - Side view of
brake side cabinet
Figure 1.2 - Back view of
brake side cabinet

Especificaciones del producto

Marca: Kenwood
Categoría: Vocero
Modelo: XM65R

¿Necesitas ayuda?

Si necesitas ayuda con Kenwood XM65R haz una pregunta a continuación y otros usuarios te responderán


Vocero Kenwood Manuales

Kenwood

Kenwood KFC-X1720P Manual de Usario

30 Septiembre 2024
Kenwood

Kenwood Excelon XR-1703HR Manual de Usario

15 Septiembre 2024
Kenwood

Kenwood KFC-WPS1000F Manual de Usario

14 Septiembre 2024
Kenwood

Kenwood Excelon KFC-X174 Manual de Usario

14 Septiembre 2024
Kenwood

Kenwood Excelon XR-1701P Manual de Usario

13 Septiembre 2024
Kenwood

Kenwood KFC-1653MRB Manual de Usario

13 Septiembre 2024
Kenwood

Kenwood KS-5200HT Manual de Usario

13 Septiembre 2024
Kenwood

Kenwood KFC-C6866S Manual de Usario

11 Septiembre 2024
Kenwood

Kenwood KFC-P509PS Manual de Usario

2 Septiembre 2024
Kenwood

Kenwood XM50F Manual de Usario

2 Septiembre 2024

Vocero Manuales

Últimos Vocero Manuales

Continental Edison

Continental Edison CELED53HP20V2B4 Manual de Usario

27 Octubre 2024
Canton

Canton Vento 830.2 Manual de Usario

27 Octubre 2024
Jamo

Jamo S7-25C Manual de Usario

27 Octubre 2024
Bowers Wilkins

Bowers Wilkins 707 S2 Manual de Usario

27 Octubre 2024
Monacor

Monacor GLS-301/GR Manual de Usario

27 Octubre 2024
Monitor Audio

Monitor Audio Silver C150 Manual de Usario

26 Octubre 2024
FBT

FBT MITUS 210M Manual de Usario

26 Octubre 2024
CyberData Systems

CyberData Systems SIP 011398 Manual de Usario

26 Octubre 2024
Lamax

Lamax PartyGo1 Play Manual de Usario

26 Octubre 2024
IKEA

IKEA SYMFONISK 405.847.50 Manual de Usario

26 Octubre 2024