Lindy 40846 Manual de Usario

Lindy Accesorio para proyector 40846

Lee a continuación 📖 el manual en español para Lindy 40846 (4 páginas) en la categoría Accesorio para proyector. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/4
© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - FIRST EDITION (November 2010)
Modular Projector Brackets
Manual
English
LINDY No. 40846, 40847, 40848 & 40849
www.lindy.com
User Manual
Thank you for purchasing the LINDY modular solution for mounting projectors in your
home, office or AV multimedia setup. Both products are universal and can support
most projectors up to a weight of 11.5Kg. The brackets and poles all have the same
black finish and also have the added benefit of a cable management system built in to
the poles.
This manual will show you how to assemble and adjust both types of bracket using
either the long or short pole. Please take note of the maximum weights supported by
the brackets to avoid any damage to your installation or equipment.
Both the long and short poles attach to the ceiling or wall in the same manner.
40846: 73 to 123cm from the wall/ceiling 31 to 41cm from the wall/ceiling 40847:
Each pole has its own cable management system. Using a conduit up the centre of
the pole you can hide unsightly power and video cables from view.
The diagram below shows how the cable is fed through the pole and can either go up
through the ceiling or out through the side of the cable cover for a tidier appearance.
Assembling the “box” bracket: 40848
The “box” bracket comes with the following pieces:
73
–
123cm
31
–
41cm
User Manual
Note: you will need to adjust the size of the “box” bracket by loosening and
tightening nuts (C) depending on the size of your projector.
Step 1
Attach 2 foam strips (G) to the underside of
the main bracket as shown. This will
protect your projector from scratching
against the metal surfaces. Connect the 4 L
pieces (D) to each corner of the main
bracket using nuts (C), washers (B) and
spanner (H).
Step 2
Attach the foam strip (G) as shown, to
bottom bracket (E). Using nuts (C) and
washers (B), attach the first part of the
bottom bracket (E) to the L piece (D).
Step 3
Attach the last foam strip (G) to the
second bottom bracket (F). Then attach
(F) to the L pieces (D) using the nuts (C)
and washers (B). The remaining nuts and
washers are to connect the two bottom
brackets (E) as shown.
Step 4
After attaching the main bracket to the
pole you can adjust the length of the
pole and lock it with screws (A).
Adjusting the bolt with the spanner (I)
will allow you to tilt and adjust your
projector to fit your requirements.

Especificaciones del producto

Marca: Lindy
Categoría: Accesorio para proyector
Modelo: 40846

¿Necesitas ayuda?

Si necesitas ayuda con Lindy 40846 haz una pregunta a continuación y otros usuarios te responderán


Accesorio para proyector Lindy Manuales

Lindy

Lindy 40846 Manual de Usario

31 Agosto 2024
Lindy

Lindy 40847 Manual de Usario

30 Agosto 2024

Accesorio para proyector Manuales

Últimos Accesorio para proyector Manuales

Barco

Barco R9853370 Manual de Usario

18 Octubre 2024
Barco

Barco R9861400 Manual de Usario

27 Septiembre 2024
Da-Lite

Da-Lite Project-O-Stand 42068 Manual de Usario

22 Septiembre 2024
My Wall

My Wall HL 41 ML Manual de Usario

17 Septiembre 2024
Speaka

Speaka SP-PWM-200 Manual de Usario

17 Septiembre 2024
Speaka

Speaka SP-PWM-100 Manual de Usario

17 Septiembre 2024
Speaka

Speaka PRB-1 Manual de Usario

17 Septiembre 2024
Roadinger

Roadinger UP-4 QCL Manual de Usario

17 Septiembre 2024
Panasonic

Panasonic ET-D3LEW300 Manual de Usario

17 Septiembre 2024
Unicol

Unicol PGG Manual de Usario

17 Septiembre 2024