Mackie 1604-VLZ Manual de Usario

Mackie consola de mezclas 1604-VLZ

Lee a continuación 📖 el manual en español para Mackie 1604-VLZ (1 páginas) en la categoría consola de mezclas. Esta guía fue útil para 11 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/1

Ribbon cable plate

Remove screws (2 each side)

(use t attach bracket o pod)o t

Ribbon cable

Jacks

8x32 screws

supplied with this kit

(2 each side)

Re-install

two rear

rubber feet

VLZ4 and VLZ3: Remove

and replace these three

screws with the M3.5x6mm

silver screws (supplied

with this kit). VLZ Pro:

Remove and re-install

these three screws only!

16220 Wo Reod- d Road NE • Woodinville • WA • 98072 • USA

Phone: 425.487.4333 • Toll-free: 800.898.3211

Fax: 425.487.4337 • www.720trees.com

Part No. 820 6--03 00 . Rev E 07/13

Like us

Watch our dang videos

The RotoPod is a bracket/rack combination that enables

the 1604VLZ4, 1604-VLZ3, 1604-VLZ PRO or 1604VLZ

to be rotated onto the same plane as the main controls;

in other words, face up. By installing the RotoPod, you

are converting the mixer from a 10-rackspace mixer with

rear-facing jacks to a 10W-rackspace configuration with

front-facing jacks. This leaves room to pass cables and

connectors through in rack-mount applications. This

setup is also great for tabletop applications when you

want instant, in-your-face access to inputs and outputs.

Parts

RotoPod Kit Contents – Part No. 090-050-90:

1 RotoPod Bracket – Part No. 550-178-00

1 RotoPod Rack Rail (marked “L”) – Part No. 550-179-00

1 RotoPod Rack Rail (marked “R”) – Part No. 550-180-00

4 #8-32 x 1/4 Black Screws – Part No. 700-004-00

6 M3.5 x 0.6 x 6 mm Silver Screws – Part No. 0020991-06

2 Rubber Feet – Part No. 750-001-00

1 Installation Instruction Sheet – Part No. 820-036-00

Tools

Required Tools (not included):

Phillips screwdriver

RotoPod Installation

1. Turn off the mixer and disconnect the power cable.

2. Flip the mixer over onto a soft, dry surface. Using the

Phillips screwdriver, remove the four screws from the

ribbon cable plate, as shown below. Be sure to store the

ribbon cable plate somewhere safe, as you may decide

to use it again one day.

3. Remove the four biggest screws

from the mixer, two from

each side. Be careful not

to pull the pod too far

away from the mixer,

as the cables are still attached!

4. Now turn the mixer back over

so you’re looking at the top again.

Rotate the pod 90˚

so the jacks are

facing up, as well.

5. Set the mixer and pod onto the

RotoPod Bracket so that the

tabs of the Rotopod fit

into the slots on the

bottoms of both the

mixer and the pod.

6. Put the four #8-32 black

screws into the bottom

of the RotoPod Bracket

and tighten them up.

7. Take off the short rack rails

(if previously installed) and

replace them with the new,

long rack rails. [“L” on the

left side of the mixer and

“R” on the right side of

the mixer].

1604VLZ4, -1604 VLZ3, -1604 VLZ PRO and 1604VLZ RotoPod Insta atll ion

Especificaciones del producto

Marca:	Mackie
Categoría:	consola de mezclas
Modelo:	1604-VLZ
Color del producto:	Wit
Peso.:	46 g
Ancho:	71 mm
Profundidad:	37 mm
Altura:	71 mm
Peso del embalaje:	119.1 g
Ancho del embalaje:	122 mm
Empaquetadura en profundidad:	112 mm
Altura del embalaje:	48 mm
Amable:	Wandmontage
Manual de usuario:	Ja
Código de seguridad internacional (IP):	IP20
Tecnología de conectividad:	Draadloos
Interfaz:	IR Draadloos
Frecuencia:	868.3 MHz
Número de canales:	2 kanalen
Tensión de funcionamiento:	230 V
Temperatura de funcionamiento (TT):	5 - 35 °C