Makita LH1040 Manual de Usario
Makita
Zaagmachine
LH1040
Lee a continuación 📖 el manual en español para Makita LH1040 (36 páginas) en la categoría Zaagmachine. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/36
1
i
ENGLISH (Original instructions)
INSTRUCTION MANUAL
DOUBLE INSULATION
IMPORTANT: Read Before Using.
Table Top Miter Saw
LH1040
LH1040F
012649
2
ENGLISH (Original instructions)
SPECIFICATIONS
Model LH1040 / LH1040F
Blade diameter 255 mm -260 mm
Blade body thickness 1.6 mm - 1.8 mm
Riving knife thickness 2.0 mm
Hole diameter
For all countries other than European countries 25.4 mm and 25 mm
For European countries 30 mm
Max. Cutting capacities (H x W) with blade 260 mm in diameter in the miter saw mode
Miter angle
Bevel angle 0° 45°
69 mm x 130 mm
right 69 mm x 85 mm, 93 mm x 67 mm
0° 93 mm x 95 mm
left 69 mm x 85 mm, 93 mm x 67 mm
35 mm x 130 mm
right 35 mm x 91 mm, 49 mm x 67 mm
45° (left) 53 mm x 95 mm
left 35 mm x 65 mm, 49 mm x 42 mm
Max. Cutting capacities at 90°in the table saw (bench saw mode) 40 mm
No load speed (min-1) 4,800
Table size (W x L) 260 mm x 405 mm
Dimensions (L x W x H) 530 mm x 476 mm x 535 mm
Net weight 14.3 kg
Safety class /II
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
END208-6
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
･ Read instruction manual.
･ DOUBLE INSULATION
･ To avoid injury from flying debris, keep
holding the saw head down, after
making cuts, until the blade has come to
a complete stop.
･ When using the tool in the miter saw
mode, secure the top table at the
topmost position so that the saw blade
never protrudes from the top surface of
the top table.
･ Do not place hand or fingers close to the
blade.
･ For your safety, remove the chips, small
pieces, etc. from the table top before
operation.
･ Only for EU countries
Do not dispose of electric equipment
together with household waste material!
In observance of the European Directive,
on Waste Electric and Electronic
Equipment and its implementation in
accordance with national law, electric
equipment that have reached the end of
their life must be collected separately
and returned to an environmentally
compatible recycling facility.
ENE060-1
Intended use
The tool is intended for accurate straight cutting and
(only when used as a miter saw on the lower table) miter
cutting in wood.
ENF002-2
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
ENG905-1
Noise
The typical A-weighted noise level determined according
to EN61029:
3
Sound pressure level (L
pA) : 93 dB (A)
Sound power level (L
WA) : 107 dB (A)
Uncertainty (K) : 3 dB (A)
Wear ear protection
ENG900-1
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN61029:
Vibration emission (ah) : 2.5 m/s2 or less
Uncertainty (K) : 1.5 m/s2
ENG901-1
• The declared vibration emission value has been
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
ENH003-14
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
Table Top Miter Saw
Model No./ Type: LH1040, LH1040F
are of series production and
Conforms to the following European Directives:
2006/42/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN61029
The technical documentation is kept by:
Makita International Europe Ltd.
Technical Department,
Michigan Drive, Tongwell,
Milton Keynes, Bucks MK15 8JD, England
11.2.2010
000230
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, 446-8502, JAPAN
ENA001-2
SAFETY INSTRUCTIONS
WARNING! When using electric tools, basic safety
precautions, including the following, should always
be followed to reduce the risk of fire, electric shock
and personal injury. Read all these instructions
before operating this product and save these
instructions.
For safe operations:
1. Keep work area clean.
Cluttered areas and benches invite injuries.
2. Consider work area environment.
Do not expose power tools to rain. Do not use
power tools in damp or wet locations. Keep work
area well lit. Do not use power tools where there is
risk to cause fire or explosion.
3. Guard against electric shock.
Avoid body contact with earthed or grounded
surfaces (e.g. pipes, radiators, ranges,
refrigerators).
4. Keep children away.
Do not let visitors touch the tool or extension cord.
All visitors should be kept away from work area.
5. Store idle tools.
When not in use, tools should be stored in a dry,
high or locked up place, out of reach of children.
6. Do not force the tool.
It will do the job better and safer at the rate for
which it was intended.
7. Use the right tool.
Do not force small tools or attachments to do the
job of a heavy duty tool. Do not use tools for
purposes not intended; for example, do not use
circular saws to cut tree limbs or logs.
8. Dress properly.
Do not wear loose clothing or jewellery, they can
be caught in moving parts. Rubber gloves and
non-skid footwear are recommended when
working outdoors. Wear protecting hair covering to
contain long hair.
9. Use safety glasses and hearing protection.
Also use face or dust mask if the cutting operation
is dusty.
Especificaciones del producto
| Marca: | Makita |
| Categoría: | Zaagmachine |
| Modelo: | LH1040 |
¿Necesitas ayuda?
Si necesitas ayuda con Makita LH1040 haz una pregunta a continuación y otros usuarios te responderán
Zaagmachine Makita Manuales
4 Octubre 2024
2 Octubre 2024
2 Octubre 2024
30 Septiembre 2024
30 Septiembre 2024
28 Septiembre 2024
24 Septiembre 2024
21 Septiembre 2024
27 Agosto 2024
23 Agosto 2024
Zaagmachine Manuales
- Zaagmachine Bosch
- Zaagmachine AEG
- Zaagmachine DeWalt
- Zaagmachine Ford
- Zaagmachine Silverline
- Zaagmachine Brennenstuhl
- Zaagmachine Ferm
- Zaagmachine Clarke
- Zaagmachine Ozito
- Zaagmachine Gude
- Zaagmachine Hitachi
- Zaagmachine Black And Decker
- Zaagmachine Vonroc
- Zaagmachine Remington
- Zaagmachine ACG
- Zaagmachine Stanley
- Zaagmachine Skil
- Zaagmachine Hyundai
- Zaagmachine Hilti
- Zaagmachine Ryobi
- Zaagmachine Florabest
- Zaagmachine Festool
- Zaagmachine Metabo
- Zaagmachine Parkside
- Zaagmachine Worx
- Zaagmachine Meec Tools
- Zaagmachine Milwaukee
- Zaagmachine Hikoki
- Zaagmachine Sun Joe
- Zaagmachine Dremel
- Zaagmachine Sovereign
- Zaagmachine Tacklife
- Zaagmachine Einhell
- Zaagmachine Baumr-AG
- Zaagmachine Husqvarna
- Zaagmachine Craftsman
- Zaagmachine Power Craft
- Zaagmachine Powerplus
- Zaagmachine Stiga
- Zaagmachine Porter-Cable
- Zaagmachine Cotech
- Zaagmachine Genesis
- Zaagmachine Trotec
- Zaagmachine Texas
- Zaagmachine Spear & Jackson
- Zaagmachine Scheppach
- Zaagmachine Atika
- Zaagmachine McCulloch
- Zaagmachine Matrix
- Zaagmachine Stihl
- Zaagmachine Dolmar
- Zaagmachine Flex
- Zaagmachine Zipper
- Zaagmachine Mafell
- Zaagmachine Fieldmann
- Zaagmachine Max
- Zaagmachine Solo
- Zaagmachine Cocraft
- Zaagmachine MTM
- Zaagmachine Herkules
- Zaagmachine Meister Craft
- Zaagmachine Toolcraft
- Zaagmachine RIDGID
- Zaagmachine Batavia
- Zaagmachine Proxxon
- Zaagmachine Gardenline
- Zaagmachine Holzmann
- Zaagmachine Fein
- Zaagmachine Oregon Scientific
- Zaagmachine Elu
- Zaagmachine Triton
- Zaagmachine BGU
- Zaagmachine Wolfcraft
- Zaagmachine Dedra
- Zaagmachine Verto
- Zaagmachine Anova
- Zaagmachine Rikon
- Zaagmachine Elektra Beckum
- Zaagmachine Toolson
- Zaagmachine Jonsered
- Zaagmachine Ultranatura
- Zaagmachine Maxbear
- Zaagmachine Stalco
Últimos Zaagmachine Manuales
3 Octubre 2024
3 Octubre 2024
3 Octubre 2024
3 Octubre 2024
2 Octubre 2024
2 Octubre 2024
2 Octubre 2024
2 Octubre 2024
2 Octubre 2024
30 Septiembre 2024