Manson NTP-5631 Manual de Usario

Manson cargador de bateria NTP-5631

Lee a continuación 📖 el manual en español para Manson NTP-5631 (4 páginas) en la categoría cargador de bateria. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

NTP- / /5661 SWITCHING MODE POWER SUPPLY 5621 5631

USER MANUAL

Keep this manual in a safe place for quick reference at all times.

This manual contains important safety and operation instructions for correct use of the power

supply. Read through the manual and pay special attention to the markings and labels of this unit

and equipment to be connected.

Pay special attention to these two types of notices used in this manual

WARNING:

Failure to observe this warning may cause injury to persons and damage to power supply

or connected equipment.

CAUTION:

Failure to observe this warning may result in damage to equipment

and Improper functioning of the power supply.

WARNING:

1. Do not use this power supply near water.

2. Do not operate or touch this power supply with wet hands.

3. Do not open the casing of the power supply when it is connected to ac mains.

4. Refer all servicing to qualied service personnel only.

5. Before replacing the AC fuse at AC socket, nd out and clear up the cause rst.

6. Replace the AC fuse with the same type and rating as the original fuse.

7. 5661 The max. output voltage of Model NTP- is 60VDC, avoid touch the metal contact part of the output

terminals.

CAUTION:

1. Use a grounded 3 pin AC source.

2. This unit is for indoor use only.

3. Do not operate or place this unit in a humid, dusty, in direct sunlight location or near any heat source.

4. Before plugging into local AC mains, check with the rating label at the back of the unit.

5. Do not block any ventilation openings of the unit.

6. This unit must be used within the specied rating, regular excessive continuous loading may cause

damage to the power supply.

7. The gauge size of input power cable must be at least 0.75mm

2 and the total length of power cable must

not exceed 3m.

OPERATION ENVIRONMENTAL CONDITION

• -80% R.H. 10

• Maximum relative humidity 80% for temperature up to 31°C decreasing linearly to 50% relative humidity at 40°C.

• Altitude up to 2000m

• Installation category: CAT 2

• Pollution degree: 2

• Mains supply voltage uctuation up to ±10% of the normal voltage

INTRODUCTIONS

This series of 100W Switching Mode Power Supplies with Current Limiting Control is designed with the objectives of

high accuracy, compactness and easy portability. Rotary encoder tuning with MCU are used for voltage and current

control. 4 digit display LCD of voltage and current for high precision.

CONTROLS AND INDICATORS

1. Power Switch

- Turns the power supply on off, when it is on the front display lights up. –

2. AC Input Socket with Fuse

3. Concealed Fuse box (ply open the cover to get to the fuse)

4. Output Voltage Tuning knob. (Quick push the knob to toggle the coarse and ne tuning)

5. Output Current Tuning knob. (Quick push the knob to toggle the coarse and ne tuning)

6. Output On/Off push button

- For Main output: Quick push this button to turn the Main output ON/OFF

- For Main output & Aux outputs: Push and hold this button for 3 seconds to turn the Main and Aux outputs

OFF, quick push this button again to turn them ON

7. n Mai Output Terminal Positive (+) Red color.

8. Main Output Terminal Negative (-) Black color

9. GND Terminal ( ) Green color

- Chassis ground terminal, normally this is to be short to (+) or (-) as required by user.

10. Aux Output 1 USB port (5VDC, 1.8 A)

11. Aux Output 2 USB port (5VDC, 1.8 A)

12. LCD Display panel showing:

- 4 digit voltmeter meter, (CV) constant voltage mode, (CC) constant current mode, , Am

- Output Terminal on/o state

- 2 digit Aux outputs Ammeter

13. Reserved (factory internal use only)

OPERATIONS

Ground Connection

Depending on the application, the power supply output terminals can be grounded in any one of the following

grounding conditions:

Negative ground black (-) negative terminal is shorted with green GND terminal. –

Positive ground red (+) positive terminal is shorted with green GND terminal. –

Floating ground green terminal is not shorted with any of the output terminals. –

Remarks:

When operating this power supply as a oating ground, high impedance leakage can exist between the power supply

circuitry and the chassis ground.

Basic Mode of Operation

This power supply is designed to operate as a constant voltage source or as a constant current source. Automatic

crossover to either mode of operation occurs when the load condition changes as following:

Constant Voltage (CV), Automatic crossover & Constant Current (CC)

The power supply functions as a constant voltage source (CV) as long as the load current is less than the preset

current limiting value. When the load current is equal to or greater than the preset current limiting value, the power

supply will automatically cross over to the constant current mode, voltage will drop, (CC) will show on the LCD display

panel and it will operate as a constant current source.

When the load current drops below the preset current limiting value, the supply returns to constant voltage (CV) mode.

Set the Output Voltage and Presetting Current Limiting Value (CC)

Turning the voltage or current knob to set your desired values.

Quick pushes on the knobs will move the decimal place for fast tuning.

Turn the knob when the desired number column is ashing otherwise you need to repeat quick pushes again.

One quick push on the current knob to see the preset current limiting value.

Connection and Operation Procedure

1. After checking with the rating label plug in to AC mains.

2. Switch on the power supply and the LCD display should be on at the same time.

3. The (CV) icon should be shown on the display.

4. Turn to current volume knob (6) to maximum clockwise if you do not require lower Current limiting value, otherwise do the

preset the (CC) limiting procedure.

5. Set your desired output voltage and then turn o the output terminal by push button (7).

6. Connect to your load positive to positive and negative to negative.

7. Turn on the output terminal again and check if display shows (CV).

8. If display shows (CC), either your preset current limiting value is too low or your load requires more voltage and current. You

need to re-access the voltage and current requirement of your load and increase the voltage or current accordingly until (CV)

appears.

Tracking Output Over Voltage Protection (OVP)

This is to protect the connected load in the event that the output voltage control circuit malfunctions, the maximum

output voltage will not exceed 30% of the adjusted voltage value at the time of the operation.

Over Temperature Protection

When the temperature inside the power supply becomes higher than a pre-determined value, the output voltage and

current of the power supply will automatically decrease to zero to prevent damage to power supply. When the

temperature inside the power supply returns to normal then the power supply will automatically return to operation

again.

Especificaciones del producto

Marca:	Manson
Categoría:	cargador de bateria
Modelo:	NTP-5631
Color del producto:	Wit
Indicadores LED:	Ja
Capacidad del acumulador/batería:	280 mAh
Tipo de embalaje:	Doos
factor vorm:	Rechtshandig
Tipo de fuente de energía:	Batterij/Accu
Material:	Kunststof
Soporta Windows:	Ja
Diseño ergonomico:	Ja
Uso recomendado:	Universeel
Iluminar desde el fondo:	Nee
Número de botones:	6
Conexión:	RF Draadloos
Fuente de carga:	Micro-USB B
Teclado numérico:	Ja
Recargable:	Ja
Incluye ratón:	Ja
Dispositivo señalador:	Nee
Teclas de Windows:	Ja
Compatible con Linux:	Ja
Teclado estilo isla:	Ja
Color de superficie:	Monochromatisch
Tipo de desplazamiento:	Wiel
Resolución de movimiento:	1600 DPI
Diseño del teclado:	QWERTY
Receptor suministrado:	Ja
tipo de botones:	Drukknoppen
Tecnología de detección de movimiento:	Optisch
Desplazarse:	Ja
Soporte de la muñeca:	Nee
Direcciones de desplazamiento:	Horizontaal
Tipo de receptor:	Micro-ontvanger
Interruptor de tecla del teclado:	Membraan keyswitch
Tamaño del teclado:	Volledige grootte (100%)
Teclado de estilo:	Recht
Dimensiones del teclado (AnxPrxAl):	430 x 125 x 15 mm
Peso del teclado:	478 g
Número-de-productos-incluidos:	2 stuk(s)
Altura del teclado ajustable:	Ja
Lenguaje del teclado:	Spaans
Dimensiones del ratón (AnxPrxAl):	106 x 68 x 38 mm
Teclas multimedia:	Ja
Tipo de batería del teclado:	Ingebouwde accu
Peso del ratón:	90 g
Perfil de tecla del teclado de computadora:	Low-profile