Meliconi Goal Plus Manual de Usario

Meliconi Mando a distancia Goal Plus

Lee a continuación 📖 el manual en español para Meliconi Goal Plus (1 páginas) en la categoría Mando a distancia. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/1
1. Make sure that the TV is ON.
2. Hold down the and
keys simultaneously until the light indicator at the top starts to fl ash
indicating that the remote control is in programming mode.
3. Press key four times then point the remote control at the appliance.
Press and release the key slowly several times.
STOP when your TV goes OFF.
4. When your TV is OFF, press the and keys simultaneously. When
you release the keys, three fl ashes indicate that the search operation
has been completed correctly.
Additional check
Check that all 7 keys are operating correctly.
If the commands work incorrectly or erratically,
you have probably entered a code for a similar
but different remote control.
In this case, repeat the search
procedure from point 2 until
all keys respond correctly to
the commands sent.
If you have any queries about :Speedy Goal Plus
• read this booklet carefully – this will help you to solve
almost all problems
• consult our Internet site to www.meliconi.com
answer all your queries more easily and quickly.
WARRANTY: 2 years
The warranty ceases to be valid if the product
is tampered with or used incorrectly.
Remote control model Speedy Goal Plus
Purchase date___________________
Identify and take note of the TV code which you have searched for,
following the code noting procedure
(see “PROGRAMMED CODE NOTING” section).
PROGRAMMED CODE NOTING
When you have programmed Speedy Goal Plus
Meliconi, note down the code on the label
in the battery compartment cover.
To fi nd the code for your remote control:
1. Hold down the and keys simultaneously
until the light indicator at the top starts to fl ash
indicating that the remote control is searching for
the code.
2. Release the keys and, within 12 seconds,
press and simultaneously.
3. Release and and pay attention to the
fl ashing of the LED: a long fl ash corresponds to a +
while a short fl ash corresponds to a - .
Note the sequence of the
9 fl ashes
and note them
down on the label in the battery compartment cover,
from left to right.
RE-PROGRAMMING YOUR REMOTE CONTROL BY
ENTERING THE CODE NOTED DOWN
If the remote control is no longer programmed because it has
been left without batteries for a long time or has fl at batteries, you
can re-program it quickly as follows:
1. Hold down the and keys simultaneously until the light
indicator at the top starts to fl ash indicating that the remote control is
programming.
2. Release the keys and, within 12 seconds, using the
and keys, enter the nine-sign code which you noted down
before. At the end,
three fl ashes
indicate that the code has been saved
correctly. If not, try the code entry procedure again from .point 1
USING YOUR REMOTE CONTROL
Once you have programmed , you can turn ON your Speedy Goal Plus
TV in three ways:
• Press or .
• Press .
• Press and simultaneously: this sends the code for programme 1.
To return to programme 1 directly, press and simultaneously.
TROUBLESHOOTING
PROBLEM
1.
The TV does not
respond and the
light indicator does
not light up when
you press a key.
2.
The TV does not
respond but the
light indicator does
light up.
3.
The TV does
not respond and
the light indicator
fl ashes.
4.
Not all remote
control commands
are working
correcting.
5.
The and
keys do not select
the programmes.
SOLUTION
1. Check that the
batteries are fi tted
correctly. If neces-
sary, replace them
with 2 new 1.5 V
AAA/LR03 alkaline
batteries.
2. Check that the
batteries are new
and that the remote
control is pointing
at the appliance
without any ob-
stacles in the way.
If required, reset
the remote control
code by repeating
the programming
procedure.
3. Batteries are low.
Replace them.
4. You may have
used the wrong
code. Reset the
remote control
code, following
the programming
procedure.
5. The original
remote control may
not have had this
function. In this
case, set the code
(press ) 9 times
as described in the
PROGRAMMING
YOUR REMOTE
CONTROL section
above.
INFO LINE
Agent’s stamp
NOTE: DURING THE SEARCH OPERATION, THE LIGHT INDICATOR FLASHES MORE QUICKLY. THE LIGHT INDICATOR
STOPS FLASHING AND YOUR REMOTE CONTROL LEAVES PROGRAMMING MODE IN THE FOLLOWING CASES:
• if no keys are pressed for 12 seconds • if you press keys other than those indicated
• if the code search list is completed. In this case, visit www.meliconi.com
Thank you
for choosing Meliconi.
This simplifi ed universal remote control contains all the main functions of most
TV remote controls on the market.
Insert the batteries and program your remote control before using it.
The remote control
requires 2 new AAA/LR03
alkaline batteries.
Insert the batteries
as shown:
FITTING THE BATTERIES
• Batteries must be changed once a year.
• Change the batteries if the light indicator starts to fl ash during use. The
batteries are low.
• When removing batteries, insert the new ones within 5 minutes or you may
have to reprogram your remote control.
• Make a note of the code for your TV on the adhesive label supplied inside
the battery compartment cover. This note will be handy if you have to
reprogram your remote control.
To use the remote control with your appliances, you must fi rst program Speedy Goal Plus as described below.
You can also visit our Internet site www.meliconi.com to have access to interactive instructions for easier and faster
remote control programming.
PROGRAMMING YOUR REMOTE CONTROL
Keep your Instructions Booklet for future reference.
USING THE KEYS AND FUNCTIONS
Control the
volume using +.
Control the
volume using -.
To select an
external terminal.
Mute key.
To select the next
programme or to turn
ON your TV.
Press them together
to turn ON your TV
on . programme 1
To select the previous
programme or
to turn ON your TV.
ON/OFF to turn OFF
your TV and,
in some cases,
to turn ON your TV.
SET-UP
Read these instructions carefully before programming your remote control!
IF YOU DO NOT HAVE THE PROGRAMME SELECTION KEYS ON YOUR
ORIGINAL REMOTE CONTROL
If your remote control does not have the programme selection keys
(e.g. / , +/-, CH+/-..etc) once you have programmed
Speedy Goal Plus, you can still select the programmes from 0 to 9, as
follows:
• Hold down the and keys simultaneously until the light
indicator starts to fl ash indicating that the remote control is
in programming mode.
• Release the keys and press within 12 9 times
seconds.
Three fl ashes
indicate that the operation has
been completed correctly.
• Make sure you can change programmes
from 0 to 9 using the and keys.
If not, repeat the search operation,
starting from point 2.

Especificaciones del producto

Marca: Meliconi
Categoría: Mando a distancia
Modelo: Goal Plus

¿Necesitas ayuda?

Si necesitas ayuda con Meliconi Goal Plus haz una pregunta a continuación y otros usuarios te responderán


Mando a distancia Meliconi Manuales

Meliconi

Meliconi gumbody light facile Manual de Usario

23 Septiembre 2024
Meliconi

Meliconi universal 4 Manual de Usario

22 Septiembre 2024
Meliconi

Meliconi Pratico 2 Manual de Usario

18 Septiembre 2024
Meliconi

Meliconi Personal 2 plus Manual de Usario

10 Septiembre 2024
Meliconi

Meliconi Speedy 2.1 Manual de Usario

2 Septiembre 2024
Meliconi

Meliconi GumBody Light Manual de Usario

2 Septiembre 2024
Meliconi

Meliconi Pratico 2.1 Manual de Usario

2 Septiembre 2024
Meliconi

Meliconi Gumbody Personal 7 plus Manual de Usario

1 Septiembre 2024
Meliconi

Meliconi Gumbody Personal 2 Manual de Usario

1 Septiembre 2024
Meliconi

Meliconi Control TV+ Manual de Usario

1 Septiembre 2024

Mando a distancia Manuales

Últimos Mando a distancia Manuales

Monacor

Monacor DRM-880WP Manual de Usario

27 Octubre 2024
Hama

Hama Spot-Pointer V2 Manual de Usario

26 Octubre 2024
Sony

Sony RM-ED022 Manual de Usario

21 Octubre 2024
Sonos

Sonos Control Manual de Usario

18 Octubre 2024
One For All

One For All URC 7935 Manual de Usario

18 Octubre 2024
Canon

Canon BG-E20 Manual de Usario

12 Octubre 2024
Neewer

Neewer RT112 Manual de Usario

8 Octubre 2024
Neewer

Neewer RT113 Manual de Usario

8 Octubre 2024
Logitech

Logitech Harmony 785 Manual de Usario

8 Octubre 2024
DSC

DSC WS4949 Manual de Usario

8 Octubre 2024