Meliconi speedy 110 plus Manual de Usario

Meliconi Mando a distancia speedy 110 plus

Lee a continuación 📖 el manual en español para Meliconi speedy 110 plus (4 páginas) en la categoría Mando a distancia. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/4
5
Thank you for choosing MELICONI.
This simplified universal remote control contains all the main functions of most TV remote controls.
Before programming and using the remote control, fit the batteries.
Keep your Instructions and Code Booklet for future reference.
USING THE KEYS AND FUNCTIONS
FITTING THE BATTERIES
GB
SET-UP
Read these instructions carefully before programming your remote control!
To command your appliances, you must program your Speedy 110 plus as described in
paragraphs Aor Bbelow.
Visit out Internet site www.meliconi.com for interactive instructions for easy and fast remote
control programming.
Before programming and using the remote control, fit the batteries.
The remote control requires 2 new AAA/LR03 alkaline batteries. Insert the batteries as shown.
The batteries must be changed once a year.
Change the batteries if the light indicator starts to flash during use.
The batteries are low.
When you remove the batteries, fit the new ones within 5 minutes or
you may have to reprogram your remote control.
Make a note of the code for your TV on the adhesive label supplied
inside the battery cover. This note will be handy if you have to
reprogram your remote control.
ON/OFF to turn OFF your TV and, in
some cases, to turn ON your TV.
Control the volume using
+
.
To select an external input terminal.
P+ to select the next program or to turn
ON your TV.
Mute key.
Control the volume using
-
.
Teletext keys:
to access Teletext
close Teletext and return to
normal viewing
Teletext page hold function
Number key.
Light indicator.
Key with additional TV functions.
P- to select the previous program
or to turn ON your TV.
6
Identify and take note of the TV code which you have searched for following the code noting procedure
(see “PROGRAMMED CODE NOTING” section).
1. Make sure that your TV is ON.
2. In the list of codes at the end of this booklet, look for your TV brand and make a note of the
corresponding TV code indicated to the side (e.g. Philips 0025). If your TV brand is not listed, apply the
global search described in paragraph B.
3. Hold down the and keys together until the light indicator at the top starts to flash indicating that
the remote control is ready for programming.
4. Release the keys, Within 15 seconds, enter the brand code previously identified (e.g. 0025). The light
indicator flashes more quickly to indicate that the remote control is ready for the search.
5. Point the remote control at the TV. Press and release the key slowly several times. Stop when your TV
goes OFF (you may have to press the key dozens of times).
6. When your TV is off, press the key to confirm.
Three long flashes indicate that the operation has been completed correctly.
Additional check
Check that some of the other functions used on your original remote control are working correctly. If the
commands function incorrectly or erratically, you have probably entered a code for a similar but different
remote control. In this case, repeat the search procedure from point 3.
BRAND SEARCH PROGRAMMING MODE
A
NOTE: during the search operation, the light indicator flashes more quickly. The light indicator
stops flashing and the remote control leaves the programming mode in the following cases:
• if no keys are pressed for 12 seconds
• if the code search list is completed. In this case, switch to programming mode B
This operation may take a few minutes.
1. Make sure that the TV is ON.
2. Hold down the and keys together until the light indicator at the top starts to flash indicating that
the remote control is ready for programming.
3. Release the keys. Within 15 seconds, enter the code 0000.
The light indicator flashes more quickly to indicate that the remote control is ready for the search.
4. Point the remote control at the TV. Press and release the key slowly several times. Stop when your TV
goes OFF (you may have to press the key over a hundred times).
5. When your TV is off, press the key to confirm. Three long flashes indicate that the operation has
been completed correctly.
Additional check
Check that some of the other functions used on your original remote control are working correctly.
If the commands function incorrectly or erratically, you have probably entered a code for a similar but
different remote control.
In this case, repeat the search procedure from point 2.
GLOBAL SEARCH REMOTE CONTROL PROGRAMMING
B
7
Identify and take note of the code which you have searched for following the code noting procedure
(see “PROGRAMMED CODE NOTING” section).
NOTE: during the search operation, the light indicator flashes more quickly. The light indicator
stops flashing and the remote control leaves the programming mode in the following cases:
if no keys are pressed for 12 seconds.
if the code search list is completed. In this case, visit www.meliconi.com
Always write down the 4-digit code for your remote control on the label inside the battery cover
after running the search and saving the code.
This may be useful if you need to reprogram your remote control in the event of accidental
cancellation or when you change used batteries.
To find the code for your remote control:
1. Hold down the and keys together until the light indicator at the top starts to flash indicating that
the remote control is programming.
2. Release the and keys. Then enter the code you noted down previously. Three flashes indicate that
the code has been saved correctly. If not, try the code entry procedure again from point 1.
PROGRAMMED CODE NOTING
1. Hold down the and keys until the light indicator at the top starts to flash.
2. Release the and keys and then press the key.
3. After a few seconds, the light indicator communicates the code you are looking for by flashing the four
numbers separately. Count the number of flashes for each code number. For example, for the code 1306,
the key flashes one, three, ten and six times to give:
= 1
= 3
= 0
= 6
4. Note this code on the label inside the battery cover, for rapid consultation.
RE-PROGRAMMING YOUR REMOTE CONTROL BY ENTERING THE CODE NOTED DOWN

Especificaciones del producto

Marca: Meliconi
Categoría: Mando a distancia
Modelo: speedy 110 plus

¿Necesitas ayuda?

Si necesitas ayuda con Meliconi speedy 110 plus haz una pregunta a continuación y otros usuarios te responderán




Mando a distancia Meliconi Manuales

Mando a distancia Manuales

Últimos Mando a distancia Manuales