Meliconi SPEEDY 2 COMBO Manual de Usario

Meliconi Mando a distancia SPEEDY 2 COMBO

Lee a continuación 📖 el manual en español para Meliconi SPEEDY 2 COMBO (4 páginas) en la categoría Mando a distancia. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

This universal remote control has the essential functions for the simplified use of an analogue or a digital

television combined with a satellite or terrestrial decoder - without having to switch between one appliance and

another. The dark blue buttons transmit the commands to the decoder while the light blue buttons control the

functions that correspond to the TV. If used with a digital TV, all the buttons control the same appliance.

BUTTON AND FUNCTION USE

FITTING THE BATTERIES

Before programming and using the remote control, fit the batteries.

The remote control requires 2 new 1.5 V AAA/LR03 alkaline batteries. Insert the batteries as shown:

• The batteries must be changed once a year.

• Replace the batteries if the indicator light on the remote control starts to

flash during use. The batteries are low.

• This remote control has a permanent memory and does not lose the

programmed codes when the batteries are removed.

• Make a note of the code for your appliances on the adhesive label found

inside the battery cover. This note will be handy if you have to reprogram

your remote control.

Warning: do not expose the remote control to sources of excessive heat

Keep your Instructions Booklet for future reference.

To select the next programme.

Interrupts and restores the TV audio.

To reduce the TV's audio volume.

Numeric keypad.

Indicator light.

Button to exit the Teletext

and return to normal viewing.

TV ON button which is occasionally

needed to turn the TV on

To increase the TV's audio volume.

To select an external input

terminal to the TV.

Button to access the Teletext.

To select the previous programme.

ON/OFF to turn OFF the TV

and in some cases to turn it ON.

Thank you for choosing MELICONI.

OFF to turn the decoder off (STB).

HOW TO PROGRAMME THE REMOTE CONTROL

- - Turn on the TV and select a programme.

- Simultaneously hold down the and buttons for 5 seconds until the upper indicator light starts to flash

indicating that the remote control is in the programming state.

- Release the buttons and enter the code 0001 within 12 seconds. The indicator light begins flashing more

quickly, indicating that the remote control is ready for the search.

- Point the remote control towards the TV. Press and slowly release the button several times, stopping when

the appliance goes off (you may need to press the button a few dozen times).

- When the appliance goes off, press the button to confirm. Three long flashes indicate that the

operation has been completed successfully.

To command your appliances, you must programme your Speedy 2 COMBO as described in the next

paragraph. For those who can connect to the internet website www.meliconi.com, you will find interactive

instructions for a faster and easier programming of your remote control.

PREPARE FOR USE

Read these instructions carefully before programming your remote control!

- Turn on the appliance and select a programme.

- Simultaneously hold down the and buttons for 5 seconds until the upper indicator light starts to flash

indicating that the remote control is in the programming state.

- Release the buttons and enter the code 0001 within 12 seconds. The indicator light begins flashing more

quickly, indicating that the remote control is ready for the search.

- Point the remote control towards the appliance. Press and slowly release the button several times,

stopping when the appliance goes off (you may need to press the button a few dozen times).

- When the appliance goes off, press the button to confirm. Three long flashes indicate that the

operation has been completed successfully.

- Turn on the TV and select a programme.

- Turn on the TV and select a programme and buttons for 5 seconds until the upper indicator light

starts to flash indicating that the remote control is in the programming state.

- buttons for 5 seconds until the upper indicator light starts to flash indicating that the remote control is in the

programming state.

- Point the remote control towards the appliance. Press and slowly release the button several times,

stopping when the appliance goes off (you may need to press the button a few dozen times).

- When the appliance goes off, press the button to confirm. Three long flashes indicate that the

operation has been completed successfully.

If you have an analogue TV and an external decoder, follow procedure A and then procedure B. Follow procedure

C if you have a digital TV.

Additional check

Check that some of the other buttons, corresponding to those on your original remote control, work correctly.

If the commands function incorrectly or erratically, you have probably entered a code for a similar but different

remote control. In this case, repeat the search procedure starting from point 3.

ANALOGUE TV PROGRAMMING

DECODER PROGRAMMING

DIGITAL TV PROGRAMMING

Remember to always make a note of the 4-digit codes for your appliances on the inside of the battery cover

when the code search and saving are finished. The codes will be required if the remote control needs to be

re-programmed following accidental deletion.

To find the code for your remote control:

1. Simultaneously press and hold for 5 seconds the buttons corresponding to the appliance for which you

would like to enter the code: and for the analogue TV, and for the decoder, or and

for the digital TV, until the indicator light starts to flash indicating that the remote control is in the

programming state.

2. Upon release insert the code number you noted beforehand. Three flashes indicate that the code has been

memorized correctly. If not, try the code entry procedure again starting from point 1.

PROGRAMMED CODE NOTING

RE-PROGRAMMING YOUR REMOTE CONTROL BY ENTERING THE CODE NOTED DOWN

1. Simultaneously hold down the and buttons for 5 seconds (if you want to know the codes for the

analogue or digital TV), or and (if you want to know the code for the decoder), until the indicator

light starts to flash indicating that the remote control is in the programming state.

2. Release the buttons and press and release the button within 8 seconds.

3. After a short pause, the indicator light produces four series of flashes with a space between them,

corresponding to the code you are looking for. Count the number of flashes; each series of flashes

corresponds to one figure in the code. 10 flashes correspond to 0. For example, the code 1306 corresponds

to:

= 1

= 3

= 0

= 6

4. Make a note of the code on the adhesive label inside the battery cover for quick and easy consultation.

Identify and take note of the code which you have discovered

following the code noting procedure

(see “PROGRAMMED CODE NOTING” section).

NOTE: The indicator light flashes more quickly during the search operation.

The indicator light stops flashing and the remote control exits the programming mode in the following

cases:

• if no buttons are pressed for 12 seconds

• if the end of the code search list has been reached. In this case, consult the website

www.meliconi.com.

Especificaciones del producto

Marca:	Meliconi
Categoría:	Mando a distancia
Modelo:	SPEEDY 2 COMBO
Color del producto:	Zwart
Peso.:	1540 g
Altura (mín.):	305 mm
Altura (máx.):	1655 mm
Capacidad máxima de peso:	5 kg
Destinado a:	Digitaal/filmcamera
diámetro de jerga:	25 mm
Montaje:	3/8"