Miiego MiiPARTY GO Manual de Usario

Miiego Auriculares MiiPARTY GO

Lee a continuación 📖 el manual en español para Miiego MiiPARTY GO (20 páginas) en la categoría Auriculares. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/20
Quick Start Guide
ENG
DK
NOR
SE
1 - 2
3 - 4
5 - 6
7 - 8
FR
-
1
211
-
1
09
DE
- 1413
LN
EST
- 7115
MiiPARTY GO
WIRELESS PORTABLE SPEAKER
ENG
18
2
3
5
9
10
11
12
13
4
7
6
SPECIFICATIONS
CARE, MAINTENANCE, SAFETY
1
This device contains a lithium accumulator.
Improper use can cause erheating and fire. ov
Any modification of the product may have consequences for safety, warranty
and proper functioning. Keep out of reach for children and animals. Product
storage and working temperature: from -5 celsius degrees to +40. Do not
expose the product to direct sunlight, heat or naked flames as it may cause
damage or explosion. Do not use the product if a part is damaged or defective.
Replace a damaged or defective device immediately. Disconnect the product
from the electrical outlet and other equipment if problems occur. Do not
charge when the product is wet. Do not leave a battery on prolonged charge
when not in use. Do not dismantle, open or shred batteries. Do not drop the
product and avoid bumping. This product may only be serviced by a qualified
technician for maintenance to reduce the risk of electric shock etc.
BT v5.0. Rechargeable 2700 mAh Li-ion battery. Full charging time: 3.5 hours.
Battery playing time: 4 hours per charge (depends on volume level). IPX4.
BT Frequency range: 2.402-2.480 MHz. Freq. Response: 70 Hz-20 KHz.
Charging input power: 5V DC/1A or 2A. RMS audio output: 30W.
Output Peak Power: 60W. Impedance: 4Ω.
Volume up / Next song
TF card slot
Charging Port
AUX IN / Reset Port
Powerbank / USB port
Wired Microphone Port
button: Power On/ Off. Pairing.
Mode (BT/ AUX/ USB/ TF). Long press: TWS.
Battery indicator - 5 LED lights
Bass (Standard/ Bass)
Lights control-button
Volume down / Previous song
Play / Pause
6
1 2 3 4 5
7 8
MIC USB
13 12 11 10 9
ENG
2
Pairing your MiiPARTY GO Wireless speaker
Charging the MiiPARTY GO speaker
Next time charging
Turning Your MiiPARTY GO On and Off
Pairing and connecting 2 x MiiPARTY GO speakers with TWS
1: Make sure the speaker is charged and turned OFF.
2: Press and hold the button for 2 seconds.
3: Activate BT on your phone or other device and search for BT devices and
select: MiiPARTY GO.
The speaker will remember your phone/device and automatically reconnect
the next time you turn it on.
An unpaired speaker will automatically turn off after 6 minutes.
Use a 5V/1A or 2A USB adapter for charging.
During charging the 5 LED battery indicator lights will flash one by one. When
fully charged the lights will stay on permanently.
Full charging time is around 3.5 hours with 2A and 7 hours with 1A.
When the first battery LED indicator light is flashing every 5 seconds, the
battery status is low and needs charging.
You will then also hear a battery warning tone every 120 seconds.
TWS only works when connecting two MiiPARTY GOs by MIIEGO together. ®
1: Turn on both speakers (BT mode). Make sure they are unconnected.
2: Press and hold button 2 (mode) on one speaker for 3 seconds. The product
emits a tone to indicate entering TWS-pairing mode.
3: Activate BT on your audio source and connect with the speaker.
ON: Press and hold the Button for 2 seconds until a tone is heard.
OFF: Press the Button once and a tone is heard.

Especificaciones del producto

Marca: Miiego
Categoría: Auriculares
Modelo: MiiPARTY GO

¿Necesitas ayuda?

Si necesitas ayuda con Miiego MiiPARTY GO haz una pregunta a continuación y otros usuarios te responderán




Auriculares Miiego Manuales

Auriculares Manuales

Últimos Auriculares Manuales